lkml.org 
[lkml]   [2021]   [Jul]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 6/7] spi: stm32h7: don't wait for EOT and flush fifo on disable
Date
In nominal cases, disable is called as part of the unprepare_message,
after receiving a EOT and after receiving all data so it doesn't
make sense to check for EOT and empty the FIFO.
Moreover, at the end of the disable, the SPI is disable (SPE) leading
to clear of all internal FIFO, leaving the IP in a known status.

Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
---
drivers/spi/spi-stm32.c | 24 ++----------------------
1 file changed, 2 insertions(+), 22 deletions(-)

diff --git a/drivers/spi/spi-stm32.c b/drivers/spi/spi-stm32.c
index c2144e3c57eb..535f4bebc010 100644
--- a/drivers/spi/spi-stm32.c
+++ b/drivers/spi/spi-stm32.c
@@ -677,13 +677,12 @@ static void stm32f4_spi_disable(struct stm32_spi *spi)
* stm32h7_spi_disable - Disable SPI controller
* @spi: pointer to the spi controller data structure
*
- * RX-Fifo is flushed when SPI controller is disabled. To prevent any data
- * loss, use stm32_spi_read_rxfifo to read the remaining bytes in RX-Fifo.
+ * RX-Fifo is flushed when SPI controller is disabled.
*/
static void stm32h7_spi_disable(struct stm32_spi *spi)
{
unsigned long flags;
- u32 cr1, sr;
+ u32 cr1;

dev_dbg(spi->dev, "disable controller\n");

@@ -696,25 +695,6 @@ static void stm32h7_spi_disable(struct stm32_spi *spi)
return;
}

- /* Wait on EOT or suspend the flow */
- if (readl_relaxed_poll_timeout_atomic(spi->base + STM32H7_SPI_SR,
- sr, !(sr & STM32H7_SPI_SR_EOT),
- 10, 100000) < 0) {
- if (cr1 & STM32H7_SPI_CR1_CSTART) {
- writel_relaxed(cr1 | STM32H7_SPI_CR1_CSUSP,
- spi->base + STM32H7_SPI_CR1);
- if (readl_relaxed_poll_timeout_atomic(
- spi->base + STM32H7_SPI_SR,
- sr, !(sr & STM32H7_SPI_SR_SUSP),
- 10, 100000) < 0)
- dev_warn(spi->dev,
- "Suspend request timeout\n");
- }
- }
-
- if (!spi->cur_usedma && spi->rx_buf && (spi->rx_len > 0))
- stm32h7_spi_read_rxfifo(spi);
-
if (spi->cur_usedma && spi->dma_tx)
dmaengine_terminate_all(spi->dma_tx);
if (spi->cur_usedma && spi->dma_rx)
--
2.25.1
\
 
 \ /
  Last update: 2021-07-07 10:32    [W:0.121 / U:0.292 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site