lkml.org 
[lkml]   [2021]   [Jun]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH V3] arm64: dts: qcom: sc7280: Add nodes for eMMC and SD card
From
Date
Hi,


> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> index 3900cfc..8b159d1 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> @@ -11,6 +11,7 @@
> #include <dt-bindings/iio/qcom,spmi-adc7-pmr735b.h>
> #include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h>
> #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
> +#include <dt-bindings/gpio/gpio.h>
> #include "sc7280.dtsi"
> #include "pm7325.dtsi"
> #include "pmr735a.dtsi"
> @@ -272,6 +273,36 @@
> status = "okay";
> };
>
> +&sdhc_1 {
> + status = "okay";
> +
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&sdc1_clk &sdc1_cmd &sdc1_data &sdc1_rclk>;
> + pinctrl-1 = <&sdc1_clk_sleep &sdc1_cmd_sleep &sdc1_data_sleep &sdc1_rclk_sleep>;

Please condense these pins into a since sdc1_on_state/sdc1_off_state (check sdc1_state_on in [1])



> +
> + non-removable;
> + no-sd;
> + no-sdio;
> +
> + vmmc-supply = <&vreg_l7b_2p9>;
> + vqmmc-supply = <&vreg_l19b_1p8>;
> +
> +};
> +
> +&sdhc_2 {
> + status = "okay";
> +
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_cd>;
> + pinctrl-1 = <&sdc2_clk_sleep &sdc2_cmd_sleep &sdc2_data_sleep>;

Ditto



> +&tlmm {
> + sdc1_clk: sdc1-clk {
> + pins = "sdc1_clk";
> + bias-disable;
> + drive-strength = <16>;
> + };
> +
> + sdc1_cmd: sdc1-cmd {
> + pins = "sdc1_cmd";
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> +
> + sdc1_data: sdc1-data {
> + pins = "sdc1_data";
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> + sdc1_rclk: sdc1-rclk {
> + pins = "sdc1_rclk";
> + bias-pull-down;
> + };
> +
> + sdc2_clk: sdc2-clk {
> + pins = "sdc2_clk";
> + bias-disable;
> + drive-strength = <16>;
> + };
> +
> + sdc2_cmd: sdc2-cmd {
> + pins = "sdc2_cmd";
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> +
> + sdc2_data: sdc2-data {
> + pins = "sdc2_data";
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> +
> + sd_cd: sd-cd {

Please make it sdc2 to keep things coherent.



> + pins = "gpio91";
> + bias-pull-up;
> + };
> +
> +};

Why are you defining on_state pins in the device dt and sleep state in the SoC one?

Most devices share a common config for these, often coming from MTP or QRD boards

and it makes little to no sense to define these separately every time, because if you hit the

rare case of needing to make a change against that, it's probably just drive-strength.



> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index 0b6f119..eab6f7b 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -24,6 +24,11 @@
>
> chosen { };
>
> + aliases {
> + mmc1 = &sdhc_1;
> + mmc2 = &sdhc_2;
> + };

This is board specific. Something might have a SDIO Wi-Fi card on it.



> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> + mmc-hs400-enhanced-strobe;

These properties should probably be in the device DT, unless the SoC controller

can only support these speeds and only at 1.8v



[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/commit/?h=for-next&id=35a4a8b6e9b133cf3a7d059ad4cf0e24cb4bd029


Konrad

\
 
 \ /
  Last update: 2021-06-09 22:47    [W:0.484 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site