lkml.org 
[lkml]   [2021]   [Jun]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 6/8] arm64: dts: qcom: pmm8155au_1: Add base dts file
Date
Add base DTS file for pmm8155au_1 along with GPIOs, power-on, rtc and vadc
nodes.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: bhupesh.linux@gmail.com
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
---
arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi | 134 ++++++++++++++++++++++
1 file changed, 134 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi

diff --git a/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi b/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi
new file mode 100644
index 000000000000..2392c742021d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+
+/ {
+ thermal-zones {
+ pmm8155au-1-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pmm8155au_1_temp>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+
+ trip2 {
+ temperature = <145000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+ };
+};
+
+&spmi_bus {
+ pmm8155au_1_0: pmic@0 {
+ compatible = "qcom,pmm8155au-1", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pon: power-on@800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x0800>;
+ pwrkey {
+ compatible = "qcom,pm8941-pwrkey";
+ interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_POWER>;
+
+ status = "disabled";
+ };
+ };
+
+ pmm8155au_1_temp: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+ io-channels = <&pmm8155au_1_adc ADC5_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmm8155au_1_adc: adc@3100 {
+ compatible = "qcom,spmi-adc5";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ die-temp@6 {
+ reg = <ADC5_DIE_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ label = "die_temp";
+ };
+ };
+
+ pmm8155au_1_adc_tm: adc-tm@3500 {
+ compatible = "qcom,spmi-adc-tm5";
+ reg = <0x3500>;
+ interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+ #thermal-sensor-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ pmm8155au_1_rtc: rtc@6000 {
+ compatible = "qcom,pm8941-rtc";
+ reg = <0x6000>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+
+ status = "disabled";
+ };
+
+ pmm8155au_1_gpios: gpio@c000 {
+ compatible = "qcom,pmm8155au-1-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmic@1 {
+ compatible = "qcom,pmm8155au-1", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
--
2.31.1
\
 
 \ /
  Last update: 2021-06-07 13:42    [W:0.203 / U:0.128 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site