lkml.org 
[lkml]   [2021]   [Jun]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 2/5] soc: qcom: geni: Add support for gpi dma
Date
GPI DMA is one of the DMA modes supported on geni, this adds support to
enable that mode

Also do better documentation of the enum geni_se_xfer_mode.

Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
drivers/soc/qcom/qcom-geni-se.c | 29 ++++++++++++++++++++++++++++-
include/linux/qcom-geni-se.h | 15 ++++++++++++++-
2 files changed, 42 insertions(+), 2 deletions(-)

diff --git a/drivers/soc/qcom/qcom-geni-se.c b/drivers/soc/qcom/qcom-geni-se.c
index fe666ea0c487..7d649d2cf31e 100644
--- a/drivers/soc/qcom/qcom-geni-se.c
+++ b/drivers/soc/qcom/qcom-geni-se.c
@@ -321,6 +321,30 @@ static void geni_se_select_dma_mode(struct geni_se *se)
writel_relaxed(val, se->base + SE_GENI_DMA_MODE_EN);
}

+static void geni_se_select_gpi_mode(struct geni_se *se)
+{
+ u32 val;
+
+ geni_se_irq_clear(se);
+
+ writel(0, se->base + SE_IRQ_EN);
+
+ val = readl(se->base + SE_GENI_S_IRQ_EN);
+ val &= ~S_CMD_DONE_EN;
+ writel(val, se->base + SE_GENI_S_IRQ_EN);
+
+ val = readl(se->base + SE_GENI_M_IRQ_EN);
+ val &= ~(M_CMD_DONE_EN | M_TX_FIFO_WATERMARK_EN |
+ M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN);
+ writel(val, se->base + SE_GENI_M_IRQ_EN);
+
+ writel(GENI_DMA_MODE_EN, se->base + SE_GENI_DMA_MODE_EN);
+
+ val = readl(se->base + SE_GSI_EVENT_EN);
+ val |= (DMA_RX_EVENT_EN | DMA_TX_EVENT_EN | GENI_M_EVENT_EN | GENI_S_EVENT_EN);
+ writel(val, se->base + SE_GSI_EVENT_EN);
+}
+
/**
* geni_se_select_mode() - Select the serial engine transfer mode
* @se: Pointer to the concerned serial engine.
@@ -328,7 +352,7 @@ static void geni_se_select_dma_mode(struct geni_se *se)
*/
void geni_se_select_mode(struct geni_se *se, enum geni_se_xfer_mode mode)
{
- WARN_ON(mode != GENI_SE_FIFO && mode != GENI_SE_DMA);
+ WARN_ON(mode != GENI_SE_FIFO && mode != GENI_SE_DMA && mode != GENI_GPI_DMA);

switch (mode) {
case GENI_SE_FIFO:
@@ -337,6 +361,9 @@ void geni_se_select_mode(struct geni_se *se, enum geni_se_xfer_mode mode)
case GENI_SE_DMA:
geni_se_select_dma_mode(se);
break;
+ case GENI_GPI_DMA:
+ geni_se_select_gpi_mode(se);
+ break;
case GENI_SE_INVALID:
default:
break;
diff --git a/include/linux/qcom-geni-se.h b/include/linux/qcom-geni-se.h
index 5114e2144b17..f5672785c0c4 100644
--- a/include/linux/qcom-geni-se.h
+++ b/include/linux/qcom-geni-se.h
@@ -8,11 +8,24 @@

#include <linux/interconnect.h>

-/* Transfer mode supported by GENI Serial Engines */
+/**
+ * enum geni_se_xfer_mode: Transfer modes supported by Serial Engines
+ *
+ * @GENI_SE_INVALID: Invalid mode
+ * @GENI_SE_FIFO: FIFO mode. Data is transferred with SE FIFO
+ * by programmed IO method
+ * @GENI_SE_DMA: Serial Engine DMA mode. Data is transferred
+ * with SE by DMAengine internal to SE
+ * @GENI_GPI_DMA: GPI DMA mode. Data is transferred using a DMAengine
+ * configured by a firmware residing on a GSI engine. This DMA name is
+ * interchangeably used as GSI or GPI which seem to imply the same DMAengine
+ */
+
enum geni_se_xfer_mode {
GENI_SE_INVALID,
GENI_SE_FIFO,
GENI_SE_DMA,
+ GENI_GPI_DMA,
};

/* Protocols supported by GENI Serial Engines */
--
2.31.1
\
 
 \ /
  Last update: 2021-06-25 07:23    [W:5.697 / U:0.300 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site