lkml.org 
[lkml]   [2021]   [Jun]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 14/16] firmware: arm_scmi: Add virtio transport
On Fri, 11 Jun 2021 17:59:35 +0100
Cristian Marussi <cristian.marussi@arm.com> wrote:

> From: Igor Skalkin <igor.skalkin@opensynergy.com>
>
> This transport enables accessing an SCMI platform as a virtio device.
>
> Implement an SCMI virtio driver according to the virtio SCMI device spec
> [1]. Virtio device id 32 has been reserved for the SCMI device [2].
>
> The virtio transport has one Tx channel (virtio cmdq, A2P channel) and
> at most one Rx channel (virtio eventq, P2A channel).
>
> The following feature bit defined in [1] is not implemented:
> VIRTIO_SCMI_F_SHARED_MEMORY.
>
> After the preparatory patches, this implements the virtio transport as
> paraphrased:
>
> Only support a single arm-scmi device (which is consistent with the SCMI
> spec). scmi-virtio init is called from arm-scmi module init. During the
> arm-scmi probing, link to the first probed scmi-virtio device. Defer
> arm-scmi probing if no scmi-virtio device is bound yet.
>
> For simplicity, restrict the number of messages which can be pending
> simultaneously according to the virtqueue capacity. (The virtqueue sizes
> are negotiated with the virtio device.)
>
> As soon as Rx channel message buffers are allocated or have been read
> out by the arm-scmi driver, feed them to the virtio device.
>
> Since some virtio devices may not have the short response time exhibited
> by SCMI platforms using other transports, set a generous response
> timeout.
>
> Limitations:
>
> - Polling is not supported.
>
> - The timeout for delayed responses has not been adjusted.
>
> [1] https://github.com/oasis-tcs/virtio-spec/blob/master/virtio-scmi.tex
> [2] https://www.oasis-open.org/committees/ballot.php?id=3496
>
> [ Peter: Adapted patch for submission to upstream. ]
>
> Co-developed-by: Peter Hilber <peter.hilber@opensynergy.com>
> Signed-off-by: Igor Skalkin <igor.skalkin@opensynergy.com>
> Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>

A few drive by comments inline.

J
> ---
> MAINTAINERS | 1 +
> drivers/firmware/Kconfig | 12 +
> drivers/firmware/arm_scmi/Makefile | 1 +
> drivers/firmware/arm_scmi/common.h | 3 +
> drivers/firmware/arm_scmi/driver.c | 3 +
> drivers/firmware/arm_scmi/virtio.c | 523 +++++++++++++++++++++++++++++
> include/uapi/linux/virtio_ids.h | 1 +
> include/uapi/linux/virtio_scmi.h | 25 ++
> 8 files changed, 569 insertions(+)
> create mode 100644 drivers/firmware/arm_scmi/virtio.c
> create mode 100644 include/uapi/linux/virtio_scmi.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index f408cf2d2781..e1b27ed11060 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -17878,6 +17878,7 @@ F: drivers/regulator/scmi-regulator.c
> F: drivers/reset/reset-scmi.c
> F: include/linux/sc[mp]i_protocol.h
> F: include/trace/events/scmi.h
> +F: include/uapi/linux/virtio_scmi.h
>
> SYSTEM RESET/SHUTDOWN DRIVERS
> M: Sebastian Reichel <sre@kernel.org>
> diff --git a/drivers/firmware/Kconfig b/drivers/firmware/Kconfig
> index e74d25065d07..2c37d5af66ad 100644
> --- a/drivers/firmware/Kconfig
> +++ b/drivers/firmware/Kconfig
> @@ -39,6 +39,18 @@ config ARM_SCMI_HAVE_MSG
> This declares whether a message passing based transport for SCMI is
> available.
>
> +# This config option includes the dependencies of ARM_SCMI_PROTOCOL so that
> +# this config doesn't show up when SCMI wouldn't be available.
> +config VIRTIO_SCMI
> + bool "Virtio transport for SCMI"
> + select ARM_SCMI_HAVE_MSG
> + depends on VIRTIO && (ARM || ARM64 || COMPILE_TEST)
> + help
> + This enables the virtio based transport for SCMI.
> +
> + If you want to use the ARM SCMI protocol between the virtio guest and
> + a host providing a virtio SCMI device, answer Y.
> +
> config ARM_SCMI_POWER_DOMAIN
> tristate "SCMI power domain driver"
> depends on ARM_SCMI_PROTOCOL || (COMPILE_TEST && OF)
> diff --git a/drivers/firmware/arm_scmi/Makefile b/drivers/firmware/arm_scmi/Makefile
> index f6b4acb8abdb..db1787606fb2 100644
> --- a/drivers/firmware/arm_scmi/Makefile
> +++ b/drivers/firmware/arm_scmi/Makefile
> @@ -5,6 +5,7 @@ scmi-transport-$(CONFIG_ARM_SCMI_HAVE_SHMEM) = shmem.o
> scmi-transport-$(CONFIG_MAILBOX) += mailbox.o
> scmi-transport-$(CONFIG_HAVE_ARM_SMCCC_DISCOVERY) += smc.o
> scmi-transport-$(CONFIG_ARM_SCMI_HAVE_MSG) += msg.o
> +scmi-transport-$(CONFIG_VIRTIO_SCMI) += virtio.o
> scmi-protocols-y = base.o clock.o perf.o power.o reset.o sensors.o system.o voltage.o
> scmi-module-objs := $(scmi-bus-y) $(scmi-driver-y) $(scmi-protocols-y) \
> $(scmi-transport-y)
> diff --git a/drivers/firmware/arm_scmi/common.h b/drivers/firmware/arm_scmi/common.h
> index fa4075336580..c143a449d278 100644
> --- a/drivers/firmware/arm_scmi/common.h
> +++ b/drivers/firmware/arm_scmi/common.h
> @@ -390,6 +390,9 @@ extern const struct scmi_desc scmi_mailbox_desc;
> #ifdef CONFIG_HAVE_ARM_SMCCC_DISCOVERY
> extern const struct scmi_desc scmi_smc_desc;
> #endif
> +#ifdef CONFIG_VIRTIO_SCMI
> +extern const struct scmi_desc scmi_virtio_desc;
> +#endif
>
> int scmi_set_transport_info(struct device *dev, void *transport_info);
> void *scmi_get_transport_info(struct device *dev);
> diff --git a/drivers/firmware/arm_scmi/driver.c b/drivers/firmware/arm_scmi/driver.c
> index bb2de15554a9..ccc7dd49261e 100644
> --- a/drivers/firmware/arm_scmi/driver.c
> +++ b/drivers/firmware/arm_scmi/driver.c
> @@ -1954,6 +1954,9 @@ static const struct of_device_id scmi_of_match[] = {
> #endif
> #ifdef CONFIG_HAVE_ARM_SMCCC_DISCOVERY
> { .compatible = "arm,scmi-smc", .data = &scmi_smc_desc},
> +#endif
> +#ifdef CONFIG_VIRTIO_SCMI
> + { .compatible = "arm,scmi-virtio", .data = &scmi_virtio_desc},
> #endif
> { /* Sentinel */ },
> };
> diff --git a/drivers/firmware/arm_scmi/virtio.c b/drivers/firmware/arm_scmi/virtio.c
> new file mode 100644
> index 000000000000..20972adf6dc7
> --- /dev/null
> +++ b/drivers/firmware/arm_scmi/virtio.c
> @@ -0,0 +1,523 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Virtio Transport driver for Arm System Control and Management Interface
> + * (SCMI).
> + *
> + * Copyright (C) 2020 OpenSynergy.
> + */
> +
> +/**
> + * DOC: Theory of Operation
> + *
> + * The scmi-virtio transport implements a driver for the virtio SCMI device.
> + *
> + * There is one Tx channel (virtio cmdq, A2P channel) and at most one Rx
> + * channel (virtio eventq, P2A channel). Each channel is implemented through a
> + * virtqueue. Access to each virtqueue is protected by spinlocks.
> + */
> +
> +#include <linux/errno.h>

> +#include <linux/of.h>
> +#include <linux/of_platform.h>
Why either of these?

perhaps
mod_devicetable.h is appropriate.

> +#include <linux/platform_device.h>
> +#include <linux/module.h>
> +#include <linux/slab.h>
> +#include <linux/virtio.h>
> +#include <linux/virtio_config.h>
> +#include <uapi/linux/virtio_ids.h>
> +#include <uapi/linux/virtio_scmi.h>
> +
> +#include "common.h"
> +
> +#define VIRTIO_SCMI_MAX_MSG_SIZE 128 /* Value may be increased. */
> +#define VIRTIO_SCMI_MAX_PDU_SIZE \
> + (VIRTIO_SCMI_MAX_MSG_SIZE + SCMI_MSG_MAX_PROT_OVERHEAD)
> +#define DESCRIPTORS_PER_TX_MSG 2
> +
> +/**
> + * struct scmi_vio_channel - Transport channel information
> + *
> + * @lock: Protects access to all members except ready.
> + * @ready_lock: Protects access to ready. If required, it must be taken before
> + * lock.
> + * @vqueue: Associated virtqueue
> + * @cinfo: SCMI Tx or Rx channel
> + * @free_list: List of unused scmi_vio_msg, maintained for Tx channels only
> + * @is_rx: Whether channel is an Rx channel
> + * @ready: Whether transport user is ready to hear about channel
> + */
> +struct scmi_vio_channel {
> + spinlock_t lock;
> + spinlock_t ready_lock;
> + struct virtqueue *vqueue;
> + struct scmi_chan_info *cinfo;
> + struct list_head free_list;
> + u8 is_rx;
> + u8 ready;
> +};
> +
> +/**
> + * struct scmi_vio_msg - Transport PDU information
> + *
> + * @request: SDU used for commands
> + * @input: SDU used for (delayed) responses and notifications
> + * @list: List which scmi_vio_msg may be part of
> + * @rx_len: Input SDU size in bytes, once input has been received
> + */
> +struct scmi_vio_msg {
> + struct scmi_msg_payld *request;
> + struct scmi_msg_payld *input;
> + struct list_head list;
> + unsigned int rx_len;
> +};
> +
> +static bool scmi_vio_have_vq_rx(struct virtio_device *vdev)
> +{
> + return virtio_has_feature(vdev, VIRTIO_SCMI_F_P2A_CHANNELS);
> +}
> +
> +static int scmi_vio_feed_vq_rx(struct scmi_vio_channel *vioch,
> + struct scmi_vio_msg *msg)
> +{
> + struct scatterlist sg_in;
> + int rc;
> + unsigned long flags;
> +
> + sg_init_one(&sg_in, msg->input, VIRTIO_SCMI_MAX_PDU_SIZE);
> +
> + spin_lock_irqsave(&vioch->lock, flags);
> +
> + rc = virtqueue_add_inbuf(vioch->vqueue, &sg_in, 1, msg, GFP_ATOMIC);
> + if (rc)
> + dev_err_once(vioch->cinfo->dev,
> + "%s() failed to add to virtqueue (%d)\n", __func__,
> + rc);
> + else
> + virtqueue_kick(vioch->vqueue);
> +
> + spin_unlock_irqrestore(&vioch->lock, flags);
> +
> + return rc;
> +}
> +
> +static void scmi_vio_complete_cb(struct virtqueue *vqueue)
> +{
> + unsigned long ready_flags;
> + unsigned long flags;
> + unsigned int length;
> + struct scmi_vio_channel *vioch;
> + struct scmi_vio_msg *msg;
> + bool cb_enabled = true;
> +
> + if (WARN_ON_ONCE(!vqueue->vdev->priv))
> + return;
> + vioch = &((struct scmi_vio_channel *)vqueue->vdev->priv)[vqueue->index];
> +
> + for (;;) {
> + spin_lock_irqsave(&vioch->ready_lock, ready_flags);
> +
> + if (!vioch->ready) {
> + if (!cb_enabled)
> + (void)virtqueue_enable_cb(vqueue);
> + goto unlock_ready_out;
> + }
> +
> + spin_lock_irqsave(&vioch->lock, flags);
> + if (cb_enabled) {
> + virtqueue_disable_cb(vqueue);
> + cb_enabled = false;
> + }
> + msg = virtqueue_get_buf(vqueue, &length);
> + if (!msg) {
> + if (virtqueue_enable_cb(vqueue))
> + goto unlock_out;
> + else

Drop the else as it doesn't add readability as far as I can see.

> + cb_enabled = true;
> + }
> + spin_unlock_irqrestore(&vioch->lock, flags);
> +
> + if (msg) {
> + msg->rx_len = length;
> +
> + /*
> + * Hold the ready_lock during the callback to avoid
> + * races when the arm-scmi driver is unbinding while
> + * the virtio device is not quiesced yet.
> + */
> + scmi_rx_callback(vioch->cinfo,
> + msg_read_header(msg->input), msg);
> + }
> + spin_unlock_irqrestore(&vioch->ready_lock, ready_flags);
> + }
> +
> +unlock_out:
> + spin_unlock_irqrestore(&vioch->lock, flags);
> +unlock_ready_out:
> + spin_unlock_irqrestore(&vioch->ready_lock, ready_flags);
> +}
> +
> +static const char *const scmi_vio_vqueue_names[] = { "tx", "rx" };
> +
> +static vq_callback_t *scmi_vio_complete_callbacks[] = {
> + scmi_vio_complete_cb,
> + scmi_vio_complete_cb
> +};
> +
> +static unsigned int virtio_get_max_msg(bool tx,
> + struct scmi_chan_info *base_cinfo)
> +{
> + struct scmi_vio_channel *vioch = base_cinfo->transport_info;
> + unsigned int ret;
> +
> + ret = virtqueue_get_vring_size(vioch->vqueue);
> +
> + /* Tx messages need multiple descriptors. */
> + if (tx)
> + ret /= DESCRIPTORS_PER_TX_MSG;
> +
> + if (ret > MSG_TOKEN_MAX) {
> + dev_info_once(
> + base_cinfo->dev,
> + "Only %ld messages can be pending simultaneously, while the %s virtqueue could hold %d\n",
> + MSG_TOKEN_MAX, tx ? "tx" : "rx", ret);
> + ret = MSG_TOKEN_MAX;
> + }
> +
> + return ret;
> +}
> +
> +static int scmi_vio_match_any_dev(struct device *dev, const void *data)
> +{
> + return 1;
> +}
> +
> +static struct virtio_driver virtio_scmi_driver; /* Forward declaration */
> +
> +static int virtio_link_supplier(struct device *dev)
> +{
> + struct device *vdev = driver_find_device(
> + &virtio_scmi_driver.driver, NULL, NULL, scmi_vio_match_any_dev);
> +
> + if (!vdev) {
> + dev_notice_once(
> + dev,
> + "Deferring probe after not finding a bound scmi-virtio device\n");
> + return -EPROBE_DEFER;
> + }
> +
> + /* Add device link for remove order and sysfs link. */
> + if (!device_link_add(dev, vdev, DL_FLAG_AUTOREMOVE_CONSUMER)) {
> + put_device(vdev);
> + dev_err(dev, "Adding link to supplier virtio device failed\n");
> + return -ECANCELED;
> + }
> +
> + put_device(vdev);
> + return scmi_set_transport_info(dev, dev_to_virtio(vdev));
> +}
> +
> +static bool virtio_chan_available(struct device *dev, int idx)
> +{
> + struct virtio_device *vdev;
> +
> + /* scmi-virtio doesn't support per-protocol channels */
> + if (is_scmi_protocol_device(dev))
> + return false;
> +
> + vdev = scmi_get_transport_info(dev);
> + if (!vdev)
> + return false;
> +
> + switch (idx) {
> + case VIRTIO_SCMI_VQ_TX:
> + return true;
> + case VIRTIO_SCMI_VQ_RX:
> + return scmi_vio_have_vq_rx(vdev);
> + default:
> + return false;
> + }
> +}
> +
> +static int virtio_chan_setup(struct scmi_chan_info *cinfo, struct device *dev,
> + bool tx)
> +{
> + unsigned long flags;
> + struct virtio_device *vdev;
> + struct scmi_vio_channel *vioch;
> + int index = tx ? VIRTIO_SCMI_VQ_TX : VIRTIO_SCMI_VQ_RX;
> + int max_msg;
> + int i;
> +
> + if (!virtio_chan_available(dev, index))
> + return -ENODEV;
> +
> + vdev = scmi_get_transport_info(dev);
> + vioch = &((struct scmi_vio_channel *)vdev->priv)[index];
> +
> + spin_lock_irqsave(&vioch->lock, flags);
> + cinfo->transport_info = vioch;
> + vioch->cinfo = cinfo;
> + spin_unlock_irqrestore(&vioch->lock, flags);
> +
> + max_msg = virtio_get_max_msg(tx, cinfo);
> +
> + for (i = 0; i < max_msg; i++) {
> + struct scmi_vio_msg *msg;
> +
> + msg = devm_kzalloc(cinfo->dev, sizeof(*msg), GFP_KERNEL);
> + if (!msg)
> + return -ENOMEM;
> +
> + if (tx) {
> + msg->request = devm_kzalloc(cinfo->dev,
> + VIRTIO_SCMI_MAX_PDU_SIZE,
> + GFP_KERNEL);
> + if (!msg->request)
> + return -ENOMEM;
> + }
> +
> + msg->input = devm_kzalloc(cinfo->dev, VIRTIO_SCMI_MAX_PDU_SIZE,
> + GFP_KERNEL);
> + if (!msg->input)
> + return -ENOMEM;
> +
> + if (tx) {
> + spin_lock_irqsave(&vioch->lock, flags);
> + list_add_tail(&msg->list, &vioch->free_list);
> + spin_unlock_irqrestore(&vioch->lock, flags);
> + } else {
> + scmi_vio_feed_vq_rx(vioch, msg);
> + }
> + }
> +
> + spin_lock_irqsave(&vioch->ready_lock, flags);
> + vioch->ready = true;
> + spin_unlock_irqrestore(&vioch->ready_lock, flags);
> +
> + return 0;
> +}
> +
> +static int virtio_chan_free(int id, void *p, void *data)
> +{
> + unsigned long flags;
> + struct scmi_chan_info *cinfo = p;
> + struct scmi_vio_channel *vioch = cinfo->transport_info;
> +
> + spin_lock_irqsave(&vioch->ready_lock, flags);
> + vioch->ready = false;
> + spin_unlock_irqrestore(&vioch->ready_lock, flags);
> +
> + scmi_free_channel(cinfo, data, id);

Blank line here would be nice + consistent.

> + return 0;
> +}
> +
> +static int virtio_send_message(struct scmi_chan_info *cinfo,
> + struct scmi_xfer *xfer)
> +{
> + struct scmi_vio_channel *vioch = cinfo->transport_info;
> + struct scatterlist sg_out;
> + struct scatterlist sg_in;
> + struct scatterlist *sgs[DESCRIPTORS_PER_TX_MSG] = { &sg_out, &sg_in };
> + unsigned long flags;
> + int rc;
> + struct scmi_vio_msg *msg;
> +
> + /*
> + * TODO: For now, we don't support polling. But it should not be
> + * difficult to add support.
> + */
> + if (xfer->hdr.poll_completion)
> + return -EINVAL;
> +
> + spin_lock_irqsave(&vioch->lock, flags);
> +
> + if (list_empty(&vioch->free_list)) {
> + spin_unlock_irqrestore(&vioch->lock, flags);
> + return -EBUSY;
> + }
> +
> + msg = list_first_entry(&vioch->free_list, typeof(*msg), list);
> + list_del(&msg->list);
> +
> + msg_tx_prepare(msg->request, xfer);
> +
> + sg_init_one(&sg_out, msg->request, msg_command_size(xfer));
> + sg_init_one(&sg_in, msg->input, msg_response_size(xfer));
> +
> + rc = virtqueue_add_sgs(vioch->vqueue, sgs, 1, 1, msg, GFP_ATOMIC);
> + if (rc) {
> + list_add(&msg->list, &vioch->free_list);
> + dev_err_once(vioch->cinfo->dev,
> + "%s() failed to add to virtqueue (%d)\n", __func__,
> + rc);
> + } else {
> + virtqueue_kick(vioch->vqueue);
> + }
> +
> + spin_unlock_irqrestore(&vioch->lock, flags);
> +
> + return rc;
> +}
> +
> +static void virtio_fetch_response(struct scmi_chan_info *cinfo,
> + struct scmi_xfer *xfer, void *msg_handle)
> +{
> + struct scmi_vio_msg *msg = msg_handle;
> + struct scmi_vio_channel *vioch = cinfo->transport_info;
> +
> + if (!msg) {
> + dev_dbg_once(&vioch->vqueue->vdev->dev,
> + "Ignoring %s() call with NULL msg_handle\n",
> + __func__);
> + return;
> + }
> +
> + msg_fetch_response(msg->input, msg->rx_len, xfer);
> +}
> +
> +static void virtio_fetch_notification(struct scmi_chan_info *cinfo,
> + size_t max_len, struct scmi_xfer *xfer,
> + void *msg_handle)
> +{
> + struct scmi_vio_msg *msg = msg_handle;
> + struct scmi_vio_channel *vioch = cinfo->transport_info;
> +
> + if (!msg) {
> + dev_dbg_once(&vioch->vqueue->vdev->dev,
> + "Ignoring %s() call with NULL msg_handle\n",
> + __func__);
> + return;
> + }
> +
> + msg_fetch_notification(msg->input, msg->rx_len, max_len, xfer);
> +}
> +
> +static void dummy_clear_channel(struct scmi_chan_info *cinfo)
> +{
> +}
> +
> +static bool dummy_poll_done(struct scmi_chan_info *cinfo,
> + struct scmi_xfer *xfer)
> +{
> + return false;
> +}
> +
> +static void virtio_drop_message(struct scmi_chan_info *cinfo, void *msg_handle)
> +{
> + unsigned long flags;
> + struct scmi_vio_channel *vioch = cinfo->transport_info;
> + struct scmi_vio_msg *msg = msg_handle;
> +
> + if (!msg) {
> + dev_dbg_once(&vioch->vqueue->vdev->dev,
> + "Ignoring %s() call with NULL msg_handle\n",
> + __func__);
> + return;
> + }
> +
> + if (vioch->is_rx) {
> + scmi_vio_feed_vq_rx(vioch, msg);
> + } else {
> + spin_lock_irqsave(&vioch->lock, flags);
> + list_add(&msg->list, &vioch->free_list);
> + spin_unlock_irqrestore(&vioch->lock, flags);
> + }
> +}
> +
> +static const struct scmi_transport_ops scmi_virtio_ops = {
> + .link_supplier = virtio_link_supplier,
> + .chan_available = virtio_chan_available,
> + .chan_setup = virtio_chan_setup,
> + .chan_free = virtio_chan_free,
> + .get_max_msg = virtio_get_max_msg,
> + .send_message = virtio_send_message,
> + .fetch_response = virtio_fetch_response,
> + .fetch_notification = virtio_fetch_notification,
> + .clear_channel = dummy_clear_channel,
> + .poll_done = dummy_poll_done,
> + .drop_message = virtio_drop_message,
> +};
> +
> +static int scmi_vio_probe(struct virtio_device *vdev)
> +{
> + struct device *dev = &vdev->dev;
> + struct scmi_vio_channel *channels;
> + bool have_vq_rx;
> + int vq_cnt;
> + int i;
> + int ret;
> + struct virtqueue *vqs[VIRTIO_SCMI_VQ_MAX_CNT];
> +
> + have_vq_rx = scmi_vio_have_vq_rx(vdev);
> + vq_cnt = have_vq_rx ? VIRTIO_SCMI_VQ_MAX_CNT : 1;
> +
> + channels = devm_kcalloc(dev, vq_cnt, sizeof(*channels), GFP_KERNEL);
> + if (!channels)
> + return -ENOMEM;
> +
> + if (have_vq_rx)
> + channels[VIRTIO_SCMI_VQ_RX].is_rx = true;
> +
> + ret = virtio_find_vqs(vdev, vq_cnt, vqs, scmi_vio_complete_callbacks,
> + scmi_vio_vqueue_names, NULL);
> + if (ret) {
> + dev_err(dev, "Failed to get %d virtqueue(s)\n", vq_cnt);
> + return ret;
> + }
> + dev_info(dev, "Found %d virtqueue(s)\n", vq_cnt);

Rather noisy given I assume there are plenty of other ways to se this
succeeded (i.e. probe succeeded)

> +
> + for (i = 0; i < vq_cnt; i++) {
> + spin_lock_init(&channels[i].lock);
> + spin_lock_init(&channels[i].ready_lock);
> + INIT_LIST_HEAD(&channels[i].free_list);
> + channels[i].vqueue = vqs[i];
> + }
> +
> + vdev->priv = channels;
> +
> + return 0;
> +}
> +
> +static void scmi_vio_remove(struct virtio_device *vdev)
> +{
> + vdev->config->reset(vdev);
> + vdev->config->del_vqs(vdev);
> +}
> +
> +static unsigned int features[] = {
> + VIRTIO_SCMI_F_P2A_CHANNELS,
> +};
> +
> +static const struct virtio_device_id id_table[] = {
> + { VIRTIO_ID_SCMI, VIRTIO_DEV_ANY_ID },
> + { 0 }
> +};
> +
> +static struct virtio_driver virtio_scmi_driver = {
> + .driver.name = "scmi-virtio",
> + .driver.owner = THIS_MODULE,
> + .feature_table = features,
> + .feature_table_size = ARRAY_SIZE(features),
> + .id_table = id_table,
> + .probe = scmi_vio_probe,
> + .remove = scmi_vio_remove,
> +};
> +
> +static int __init virtio_scmi_init(void)
> +{
> + return register_virtio_driver(&virtio_scmi_driver);
> +}
> +
> +static void __exit virtio_scmi_exit(void)
> +{
> + unregister_virtio_driver(&virtio_scmi_driver);
> +}

module_virtio_driver() ?

> +
> +const struct scmi_desc scmi_virtio_desc = {
> + .init = virtio_scmi_init,
> + .exit = virtio_scmi_exit,
> + .ops = &scmi_virtio_ops,
> + .max_rx_timeout_ms = 60000, /* for non-realtime virtio devices */
> + .max_msg = 0, /* overridden by virtio_get_max_msg() */
> + .max_msg_size = VIRTIO_SCMI_MAX_MSG_SIZE,
> +};
> diff --git a/include/uapi/linux/virtio_ids.h b/include/uapi/linux/virtio_ids.h
> index 4fe842c3a3a9..ead8178efffa 100644
> --- a/include/uapi/linux/virtio_ids.h
> +++ b/include/uapi/linux/virtio_ids.h
> @@ -55,6 +55,7 @@
> #define VIRTIO_ID_FS 26 /* virtio filesystem */
> #define VIRTIO_ID_PMEM 27 /* virtio pmem */
> #define VIRTIO_ID_MAC80211_HWSIM 29 /* virtio mac80211-hwsim */
> +#define VIRTIO_ID_SCMI 32 /* virtio SCMI */
> #define VIRTIO_ID_BT 40 /* virtio bluetooth */
>
> #endif /* _LINUX_VIRTIO_IDS_H */
> diff --git a/include/uapi/linux/virtio_scmi.h b/include/uapi/linux/virtio_scmi.h
> new file mode 100644
> index 000000000000..732b01504c35
> --- /dev/null
> +++ b/include/uapi/linux/virtio_scmi.h
> @@ -0,0 +1,25 @@
> +/* SPDX-License-Identifier: ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) */
> +/*
> + * Copyright (C) 2020 OpenSynergy GmbH
> + */
> +
> +#ifndef _UAPI_LINUX_VIRTIO_SCMI_H
> +#define _UAPI_LINUX_VIRTIO_SCMI_H
> +
> +#include <linux/virtio_types.h>
> +
> +/* Feature bits */

Drop comment for things that aren't here?

> +
> +/* Device implements some SCMI notifications, or delayed responses. */
> +#define VIRTIO_SCMI_F_P2A_CHANNELS 0
> +
> +/* Device implements any SCMI statistics shared memory region */
> +#define VIRTIO_SCMI_F_SHARED_MEMORY 1
> +
> +/* Virtqueues */
> +
> +#define VIRTIO_SCMI_VQ_TX 0 /* cmdq */
> +#define VIRTIO_SCMI_VQ_RX 1 /* eventq */
> +#define VIRTIO_SCMI_VQ_MAX_CNT 2
> +
> +#endif /* _UAPI_LINUX_VIRTIO_SCMI_H */

\
 
 \ /
  Last update: 2021-06-14 16:25    [W:1.727 / U:0.236 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site