lkml.org 
[lkml]   [2021]   [May]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 1/3] ARM: dts: aspeed: ast2600evb: Add sdhci node and gpio regulator for A2 evb.
The 05/24/2021 10:46, Joel Stanley wrote:
> On Mon, 24 May 2021 at 02:35, Steven Lee <steven_lee@aspeedtech.com> wrote:
> >
> > The 05/21/2021 09:25, Joel Stanley wrote:
> > > Hi Steven,
> > >
> > > On Thu, 20 May 2021 at 10:16, Steven Lee <steven_lee@aspeedtech.com> wrote:
> > > >
> > > > AST2600 A2(or newer) EVB has gpio regulators for toggling signal voltage
> > > > between 3.3v and 1.8v, the patch adds sdhci node and gpio regulator in the
> > > > new dts file and adds commment for describing the reference design.
> > >
> > > spelling: comment
> > >
> >
> > Thanks, will correct the typo.
> >
> > > I need you to justify the separate dts for the A2 EVB.
> > >
> > > What would happen if this device tree was loaded on to an A1 or A0?
> > >
> >
> > Since the clock default value(SCU210) of A1 and A0 are different to A2,
> > the following error would happen if A2 device tree was loaded on A1/A0.
> >
> > ```
> > [ 133.179825] mmc1: Reset 0x4 never completed.
> > [ 133.184599] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
> > [ 133.191786] mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00000002
> > [ 133.198972] mmc1: sdhci: Blk size: 0x00007008 | Blk cnt: 0x00000001
> > [ 133.206158] mmc1: sdhci: Argument: 0x00000c00 | Trn mode: 0x00000013
> > [ 133.213343] mmc1: sdhci: Present: 0x01f70001 | Host ctl: 0x00000011
> > [ 133.220528] mmc1: sdhci: Power: 0x0000000f | Blk gap: 0x00000000
> > [ 133.227713] mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x00008007
> > [ 133.234898] mmc1: sdhci: Timeout: 0x0000000b | Int stat: 0x00000000
> > [ 133.242083] mmc1: sdhci: Int enab: 0x00ff0083 | Sig enab: 0x00ff0083
> > [ 133.249268] mmc1: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000
> > [ 133.256453] mmc1: sdhci: Caps: 0x07f80080 | Caps_1: 0x00000007
> > [ 133.263638] mmc1: sdhci: Cmd: 0x0000341a | Max curr: 0x001f0f08
> > [ 133.270824] mmc1: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0x01dd7f7f
> > [ 133.278009] mmc1: sdhci: Resp[2]: 0x325b5900 | Resp[3]: 0x00400e00
> > [ 133.285193] mmc1: sdhci: Host ctl2: 0x00000000
> > [ 133.290148] mmc1: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0xbe041200
> > [ 133.297332] mmc1: sdhci: ============================================
> >
> > ```
> >
> > Besides, A1/A0 EVBs don't have regulator, vmmc and vqmmc should be
> > removed from sdhci node of A1/A0 dts.
> >
> > > Would this device tree be used for the A3 (and any future revision?)
> > >
> >
> > Yes, A3 can use the A2 dts.
> >
> > > An alternative proposal: we modify the ast2600-evb.dts to support the
> > > A2 (which I assume would also support the A3).
> > >
> > > If we need a separate board file for the A0 and A1 EVB, we add a new
> > > one that supports these earlier revisions. Or we decide to only
> > > support the latest revision in mainline.
> > >
> >
> > In this patch, I add a new dts to support A2 sdhci, and include the
> > original dts since the other settings can be loaded on A2.
> > Do you mean creating a new file(e.g. aspeed-ast2600-evb-a1.dts) for A1,
> > and modifying the original aspeed-ast2600-evb.dts for supporting A2?
>
> Yes, that would be my suggestion. The aspeed-ast2600-evb-a1.dts could
> include the aspeed-ast2600-evb.dts.
>

Thanks for the prompt reply, I will add aspeed-ast2600-evb-a1.dts for
A1 and A0.

> > If we decide to only support the latest version in mainline, users
> > should mark vmmc and vqmmc as comment and modify clk-phase manually
> > for supporting A1.
>
> If you believe there will be users of the A1 for some time, then I
> think it makes sense to support both A1 and future boards in mainline.
>
> Cheers,
>
> Joel

\
 
 \ /
  Last update: 2021-05-24 05:03    [W:0.816 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site