lkml.org 
[lkml]   [2021]   [Apr]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH] net: phy: fix PHY possibly unwork after MDIO bus resume back
Date
On 06.04.2021 12:07, Joakim Zhang wrote:
>
>> -----Original Message-----
>> From: Heiner Kallweit <hkallweit1@gmail.com>
>> Sent: 2021年4月6日 14:29
>> To: Joakim Zhang <qiangqing.zhang@nxp.com>; christian.melki@t2data.com;
>> andrew@lunn.ch; linux@armlinux.org.uk; davem@davemloft.net;
>> kuba@kernel.org
>> Cc: netdev@vger.kernel.org; linux-kernel@vger.kernel.org; dl-linux-imx
>> <linux-imx@nxp.com>
>> Subject: Re: [PATCH] net: phy: fix PHY possibly unwork after MDIO bus resume
>> back
>>
>> On 06.04.2021 04:07, Joakim Zhang wrote:
>>>
>>> Hi Heiner,
>>>
>>>> -----Original Message-----
>>>> From: Heiner Kallweit <hkallweit1@gmail.com>
>>>> Sent: 2021年4月5日 20:10
>>>> To: christian.melki@t2data.com; Joakim Zhang
>>>> <qiangqing.zhang@nxp.com>; andrew@lunn.ch; linux@armlinux.org.uk;
>>>> davem@davemloft.net; kuba@kernel.org
>>>> Cc: netdev@vger.kernel.org; linux-kernel@vger.kernel.org;
>>>> dl-linux-imx <linux-imx@nxp.com>
>>>> Subject: Re: [PATCH] net: phy: fix PHY possibly unwork after MDIO bus
>>>> resume back
>>>>
>>>> On 05.04.2021 10:43, Christian Melki wrote:
>>>>> On 4/5/21 12:48 AM, Heiner Kallweit wrote:
>>>>>> On 04.04.2021 16:09, Heiner Kallweit wrote:
>>>>>>> On 04.04.2021 12:07, Joakim Zhang wrote:
>>>>>>>> commit 4c0d2e96ba055 ("net: phy: consider that suspend2ram may
>>>>>>>> cut off PHY power") invokes phy_init_hw() when MDIO bus resume,
>>>>>>>> it will soft reset PHY if PHY driver implements soft_reset callback.
>>>>>>>> commit 764d31cacfe4 ("net: phy: micrel: set soft_reset callback
>>>>>>>> to genphy_soft_reset for KSZ8081") adds soft_reset for KSZ8081.
>>>>>>>> After these two patches, I found i.MX6UL 14x14 EVK which
>>>>>>>> connected to KSZ8081RNB doesn't work any more when system
>> resume
>>>>>>>> back, MAC
>>>> driver is fec_main.c.
>>>>>>>>
>>>>>>>> It's obvious that initializing PHY hardware when MDIO bus resume
>>>>>>>> back would introduce some regression when PHY implements
>>>>>>>> soft_reset. When I
>>>>>>>
>>>>>>> Why is this obvious? Please elaborate on why a soft reset should
>>>>>>> break something.
>>>>>>>
>>>>>>>> am debugging, I found PHY works fine if MAC doesn't support
>>>>>>>> suspend/resume or phy_stop()/phy_start() doesn't been called
>>>>>>>> during suspend/resume. This let me realize, PHY state machine
>>>>>>>> phy_state_machine() could do something breaks the PHY.
>>>>>>>>
>>>>>>>> As we known, MAC resume first and then MDIO bus resume when
>>>>>>>> system resume back from suspend. When MAC resume, usually it will
>>>>>>>> invoke
>>>>>>>> phy_start() where to change PHY state to PHY_UP, then trigger the
>>>>>>>> stat> machine to run now. In phy_state_machine(), it will
>>>>>>>> start/config auto-nego, then change PHY state to PHY_NOLINK, what
>>>>>>>> to next is periodically check PHY link status. When MDIO bus
>>>>>>>> resume, it will initialize PHY hardware, including soft_reset,
>>>>>>>> what would soft_reset affect seems various from different PHYs.
>>>>>>>> For KSZ8081RNB, when it in PHY_NOLINK state and then perform a
>>>>>>>> soft reset,
>>>> it will never complete auto-nego.
>>>>>>>
>>>>>>> Why? That would need to be checked in detail. Maybe chip errata
>>>>>>> documentation provides a hint.
>>>>>>>
>>>>>>
>>>>>> The KSZ8081 spec says the following about bit BMCR_PDOWN:
>>>>>>
>>>>>> If software reset (Register 0.15) is used to exit power-down mode
>>>>>> (Register 0.11 = 1), two software reset writes (Register 0.15 = 1)
>>>>>> are required. The first write clears power-down mode; the second
>>>>>> write resets the chip and re-latches the pin strapping pin values.
>>>>>>
>>>>>> Maybe this causes the issue you see and genphy_soft_reset() isn't
>>>>>> appropriate for this PHY. Please re-test with the KSZ8081 soft
>>>>>> reset following the spec comment.
>>>>>>
>>>>>
>>>>> Interesting. Never expected that behavior.
>>>>> Thanks for catching it. Skimmed through the datasheets/erratas.
>>>>> This is what I found (micrel.c):
>>>>>
>>>>> 10/100:
>>>>> 8001 - Unaffected?
>>>>> 8021/8031 - Double reset after PDOWN.
>>>>> 8041 - Errata. PDOWN broken. Recommended do not use. Unclear if
>>>>> reset solves the issue since errata says no error after reset but is
>>>>> also claiming that only toggling PDOWN (may) or power will help.
>>>>> 8051 - Double reset after PDOWN.
>>>>> 8061 - Double reset after PDOWN.
>>>>> 8081 - Double reset after PDOWN.
>>>>> 8091 - Double reset after PDOWN.
>>>>>
>>>>> 10/100/1000:
>>>>> Nothing in gigabit afaics.
>>>>>
>>>>> Switches:
>>>>> 8862 - Not affected?
>>>>> 8863 - Errata. PDOWN broken. Reset will not help. Workaround exists.
>>>>> 8864 - Not affected?
>>>>> 8873 - Errata. PDOWN broken. Reset will not help. Workaround exists.
>>>>> 9477 - Errata. PDOWN broken. Will randomly cause link failure on
>>>>> adjacent links. Do not use.
>>>>>
>>>>> This certainly explains a lot.
>>>>>
>>>>>>>>
>>>>>>>> This patch changes PHY state to PHY_UP when MDIO bus resume back,
>>>>>>>> it should be reasonable after PHY hardware re-initialized. Also
>>>>>>>> give state machine a chance to start/config auto-nego again.
>>>>>>>>
>>>>>>>
>>>>>>> If the MAC driver calls phy_stop() on suspend, then
>>>>>>> phydev->suspended is true and mdio_bus_phy_may_suspend() returns
>>>>>>> false. As a consequence
>>>>>>> phydev->suspended_by_mdio_bus is false and mdio_bus_phy_resume()
>>>>>>> skips the PHY hw initialization.
>>>>>>> Please also note that mdio_bus_phy_suspend() calls
>>>>>>> phy_stop_machine() that sets the state to PHY_UP.
>>>>>>>
>>>>>>
>>>>>> Forgot that MDIO bus suspend is done before MAC driver suspend.
>>>>>> Therefore disregard this part for now.
>>>>>>
>>>>>>> Having said that the current argumentation isn't convincing. I'm
>>>>>>> not aware of such issues on other systems, therefore it's likely
>>>>>>> that something is system-dependent.
>>>>>>>
>>>>>>> Please check the exact call sequence on your system, maybe it
>>>>>>> provides a hint.
>>>>>>>
>>>>>>>> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
>>>>>>>> ---
>>>>>>>> drivers/net/phy/phy_device.c | 7 +++++++
>>>>>>>> 1 file changed, 7 insertions(+)
>>>>>>>>
>>>>>>>> diff --git a/drivers/net/phy/phy_device.c
>>>>>>>> b/drivers/net/phy/phy_device.c index cc38e326405a..312a6f662481
>>>>>>>> 100644
>>>>>>>> --- a/drivers/net/phy/phy_device.c
>>>>>>>> +++ b/drivers/net/phy/phy_device.c
>>>>>>>> @@ -306,6 +306,13 @@ static __maybe_unused int
>>>> mdio_bus_phy_resume(struct device *dev)
>>>>>>>> ret = phy_resume(phydev);
>>>>>>>> if (ret < 0)
>>>>>>>> return ret;
>>>>>>>> +
>>>>>>>> + /* PHY state could be changed to PHY_NOLINK from MAC controller
>>>> resume
>>>>>>>> + * rounte with phy_start(), here change to PHY_UP after
>>>> re-initializing
>>>>>>>> + * PHY hardware, let PHY state machine to start/config
>>>>>>>> +auto-nego
>>>> again.
>>>>>>>> + */
>>>>>>>> + phydev->state = PHY_UP;
>>>>>>>> +
>>>>>>>> no_resume:
>>>>>>>> if (phydev->attached_dev && phydev->adjust_link)
>>>>>>>> phy_start_machine(phydev);
>>>>>>>>
>>>>>>>
>>>>>>
>>>>>
>>>>
>>>> This is a quick draft of the modified soft reset for KSZ8081.
>>>> Some tests would be appreciated.
>>>>
>>>
>>> I test this patch at my side, unfortunately, it still can't work.
>>>
>>> I have not found what soft reset would affect in 8081 spec, is there
>>> ang common Description for different PHYs?
>>>
>>
>> You can check the clause 22 spec: 802.3 22.2.4.1.1
>>
>> Apart from that you can check BMCR value and which modes your PHY
>> advertises after a soft reset. If the PHY indeed wouldn't restart aneg after a
>> soft reset, then it would be the only one with this behavior I know. And I'd
>> wonder why there aren't more such reports.
>
> Hi Heiner,
>
> We have reasons to believe it is a weird behavior of KSZ8081. I have another two PHYs at my side, AR8031 and RTL8211FD,
> they can work fine if soft_reset implemented.
>
> As commit message described, phy_start() would change PHY state to PHY_UP finally to PHY_NOLINK when MAC resume.
> After MDIO bus resume back, it will periodically check link status. I did below code change to dump all PHY registers.
>
> --- a/drivers/net/phy/phy.c
> +++ b/drivers/net/phy/phy.c
> @@ -35,7 +35,7 @@
> #include <net/genetlink.h>
> #include <net/sock.h>
>
> -#define PHY_STATE_TIME HZ
> +#define PHY_STATE_TIME (10 * HZ)
>
> #define PHY_STATE_STR(_state) \
> case PHY_##_state: \
> @@ -738,6 +738,28 @@ static int phy_check_link_status(struct phy_device *phydev)
> if (err)
> return err;
>
> + printk("offset 0x00 data = %0x\n", phy_read(phydev, 0x00));
> + printk("offset 0x01 data = %0x\n", phy_read(phydev, 0x01));
> + printk("offset 0x02 data = %0x\n", phy_read(phydev, 0x02));
> + printk("offset 0x03 data = %0x\n", phy_read(phydev, 0x03));
> + printk("offset 0x04 data = %0x\n", phy_read(phydev, 0x04));
> + printk("offset 0x05 data = %0x\n", phy_read(phydev, 0x05));
> + printk("offset 0x06 data = %0x\n", phy_read(phydev, 0x06));
> + printk("offset 0x07 data = %0x\n", phy_read(phydev, 0x07));
> + printk("offset 0x08 data = %0x\n", phy_read(phydev, 0x08));
> + printk("offset 0x09 data = %0x\n", phy_read(phydev, 0x09));
> + printk("offset 0x10 data = %0x\n", phy_read(phydev, 0x10));
> + printk("offset 0x11 data = %0x\n", phy_read(phydev, 0x11));
> + printk("offset 0x15 data = %0x\n", phy_read(phydev, 0x15));
> + printk("offset 0x16 data = %0x\n", phy_read(phydev, 0x16));
> + printk("offset 0x17 data = %0x\n", phy_read(phydev, 0x17));
> + printk("offset 0x18 data = %0x\n", phy_read(phydev, 0x18));
> + printk("offset 0x1b data = %0x\n", phy_read(phydev, 0x1b));
> + printk("offset 0x1c data = %0x\n", phy_read(phydev, 0x1c));
> + printk("offset 0x1d data = %0x\n", phy_read(phydev, 0x1d));
> + printk("offset 0x1e data = %0x\n", phy_read(phydev, 0x1e));
> + printk("offset 0x1f data = %0x\n", phy_read(phydev, 0x1f));
> + printk("\n\n");
> if (phydev->link && phydev->state != PHY_RUNNING) {
> phy_check_downshift(phydev);
> phydev->state = PHY_RUNNING;
>
> After MDIO bus resume back, results as below:
>
> [ 119.545383] offset 0x00 data = 1100
> [ 119.549237] offset 0x01 data = 7849
> [ 119.563125] offset 0x02 data = 22
> [ 119.566810] offset 0x03 data = 1560
> [ 119.570597] offset 0x04 data = 85e1
> [ 119.588016] offset 0x05 data = 0
> [ 119.592891] offset 0x06 data = 4
> [ 119.596452] offset 0x07 data = 2001
> [ 119.600233] offset 0x08 data = 0
> [ 119.617864] offset 0x09 data = 0
> [ 119.625990] offset 0x10 data = 0
> [ 119.629576] offset 0x11 data = 0
> [ 119.642735] offset 0x15 data = 0
> [ 119.646332] offset 0x16 data = 202
> [ 119.650030] offset 0x17 data = 5c02
> [ 119.668054] offset 0x18 data = 801
> [ 119.672997] offset 0x1b data = 0
> [ 119.676565] offset 0x1c data = 0
> [ 119.680084] offset 0x1d data = 0
> [ 119.698031] offset 0x1e data = 20
> [ 119.706246] offset 0x1f data = 8190
> [ 119.709984]
> [ 119.709984]
> [ 120.182120] offset 0x00 data = 100
> [ 120.185894] offset 0x01 data = 784d
> [ 120.189681] offset 0x02 data = 22
> [ 120.206319] offset 0x03 data = 1560
> [ 120.210171] offset 0x04 data = 8061
> [ 120.225353] offset 0x05 data = 0
> [ 120.228948] offset 0x06 data = 4
> [ 120.242936] offset 0x07 data = 2001
> [ 120.246792] offset 0x08 data = 0
> [ 120.250313] offset 0x09 data = 0
> [ 120.266748] offset 0x10 data = 0
> [ 120.270335] offset 0x11 data = 0
> [ 120.284167] offset 0x15 data = 0
> [ 120.287760] offset 0x16 data = 202
> [ 120.301031] offset 0x17 data = 3c02
> [ 120.313209] offset 0x18 data = 801
> [ 120.316983] offset 0x1b data = 0
> [ 120.320513] offset 0x1c data = 1
> [ 120.336589] offset 0x1d data = 0
> [ 120.340184] offset 0x1e data = 115
> [ 120.355357] offset 0x1f data = 8190
> [ 120.359112]
> [ 120.359112]
> [ 129.785396] offset 0x00 data = 1100
> [ 129.789252] offset 0x01 data = 7849
> [ 129.809951] offset 0x02 data = 22
> [ 129.815018] offset 0x03 data = 1560
> [ 129.818845] offset 0x04 data = 85e1
> [ 129.835808] offset 0x05 data = 0
> [ 129.839398] offset 0x06 data = 4
> [ 129.854514] offset 0x07 data = 2001
> [ 129.858371] offset 0x08 data = 0
> [ 129.873357] offset 0x09 data = 0
> [ 129.876954] offset 0x10 data = 0
> [ 129.880472] offset 0x11 data = 0
> [ 129.896450] offset 0x15 data = 0
> [ 129.900038] offset 0x16 data = 202
> [ 129.915041] offset 0x17 data = 5c02
> [ 129.918889] offset 0x18 data = 801
> [ 129.932735] offset 0x1b data = 0
> [ 129.946830] offset 0x1c data = 0
> [ 129.950424] offset 0x1d data = 0
> [ 129.964585] offset 0x1e data = 0
> [ 129.968192] offset 0x1f data = 8190
> [ 129.972938]
> [ 129.972938]
> [ 130.425125] offset 0x00 data = 100
> [ 130.428889] offset 0x01 data = 784d
> [ 130.442671] offset 0x02 data = 22
> [ 130.446360] offset 0x03 data = 1560
> [ 130.450142] offset 0x04 data = 8061
> [ 130.467207] offset 0x05 data = 0
> [ 130.470789] offset 0x06 data = 4
> [ 130.485071] offset 0x07 data = 2001
> [ 130.488934] offset 0x08 data = 0
> [ 130.504320] offset 0x09 data = 0
> [ 130.507911] offset 0x10 data = 0
> [ 130.520950] offset 0x11 data = 0
> [ 130.532865] offset 0x15 data = 0
> [ 130.536461] offset 0x16 data = 202
> [ 130.540156] offset 0x17 data = 3c02
> [ 130.557218] offset 0x18 data = 801
> [ 130.560987] offset 0x1b data = 0
> [ 130.575158] offset 0x1c data = 1
> [ 130.578754] offset 0x1d data = 0
> [ 130.593543] offset 0x1e data = 115
> [ 130.597312] offset 0x1f data = 8190
>
> We can see that BMCR and BMSR changes from 0x1100,0x7849 to 0x100,0x784d (BMCR[12] bit and BMSR[2]), and loop it.
> Above process is auto-nego enabled, link is down, auto-nego is disabled, link is up. And auto-nego complete bit is always 0.
>
> PHY seems become unstable if soft reset after start/config auto-nego. I also want to fix it in micrel driver, but failed.
>

Waiting for ANEG_COMPLETE to be set wouldn't be a good option. Aneg may never
complete for different reasons, e.g. no physical link. And even if we use a
timeout this may add unwanted delays.

> Do you have any other insights that can help me further locate the issue? Thanks.
>

I think current MAC/PHY PM handling isn't perfect. Often we have the following
scenario:

*suspend*
1. PHY is suspended (mdio_bus_phy_suspend)
2. MAC suspend callback (typically involving phy_stop())

*resume*
1. MAC resume callback (typically involving phy_start())
2. PHY is resumed (mdio_bus_phy_resume), incl. calling phy_init_hw()

Calling phy_init_hw() after phy_start() doesn't look right.
It seems to work in most cases, but there's a certain risk
that phy_init_hw() overwrites something, e.g. the advertised
modes.
I think we have two valid scenarios:

1. phylib PM callbacks are used, then the MAC driver shouldn't
touch the PHY in its PM callbacks, especially not call
phy_stop/phy_start.

2. MAC PM callbacks take care also of the PHY. Then I think we would
need a flag at the phy_device telling it to make the PHY PM
callbacks a no-op.

Andrew, Russell: What do you think?

> Best Regards,
> Joakim Zhang
>
> [...]
>
Heiner

\
 
 \ /
  Last update: 2021-04-06 13:43    [W:0.824 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site