lkml.org 
[lkml]   [2021]   [Mar]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 4/4] ARM: dts: Fix-up EMMC2 controller's frequency
From
Date
Am 26.03.21 um 17:17 schrieb Nicolas Saenz Julienne:
> On Thu, 2021-03-25 at 20:11 +0100, Stefan Wahren wrote:
>> Am 24.03.21 um 16:34 schrieb Nicolas Saenz Julienne:
>>> Hi Stefan,
>>>
>>> On Wed, 2021-03-24 at 16:16 +0100, Stefan Wahren wrote:
>>>> Hi Nicolas,
>>>>
>>>> Am 22.03.21 um 19:58 schrieb Nicolas Saenz Julienne:
>>>>> From: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
>>>>>
>>>>> Force emmc2's frequency to 150MHz as the default 100MHz (set by FW)
>>>>> seems to interfere with the VPU clock when setup at frequencies bigger
>>>>> than 500MHz (a pretty common case). This ends up causing unwarranted
>>>>> SDHCI CMD hangs when no SD card is present.
>>>>>
>>>>> Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
>>>>> ---
>>>>>  arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 6 ++++++
>>>>>  1 file changed, 6 insertions(+)
>>>>>
>>>>> diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
>>>>> index 3b4ab947492a..9aa8408d9960 100644
>>>>> --- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
>>>>> +++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
>>>>> @@ -257,6 +257,12 @@ &emmc2 {
>>>>>   vqmmc-supply = <&sd_io_1v8_reg>;
>>>>>   vmmc-supply = <&sd_vcc_reg>;
>>>>>   broken-cd;
>>>>> + /*
>>>>> + * Force the frequency to 150MHz as the default 100MHz seems to
>>>>> + * interfere with the VPU clock when setup at frequencies bigger than
>>>>> + * 500MHz, causing unwarranted CMD hangs.
>>>>> + */
>>>>> + clock-frequency = <150000000>;
>>>> i don't want to bike-shed here, but is there any chance to solve this in
>>>> clk-bcm2835 in a less hacky way?
>>> What do you have in mind?
>> Sorry, nothing specific.
>>> All I can think of is adding some kind of heuristic to the clock's prepare()
>>> callback. That said, I don't feel it would be a better solution than this.
>> Based on my limited knowledge and an old SD card specification, all
>> possibly connected devices could have different frequencies. So my
>> concern here is, that in case we limit the frequency to a specific value
>> we could break things just to suppress a warning.
> SDHCI should be able to handle up to 233MHz IIRC, and there are divisors
> available, it depends on the implementation but the worst kind provide /2^n.
> Not perfect, but good enough for things to work.
>
> Now, I've been having a deeper look into how clocks are handled, and found two
> new clues:
>
> - First of all RPi4's sdhci-iproc needs SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
> that is, the controller isn't properly identifying the clock frequency fed
> into it, and defaults to saying it's configured at 100MHz. I'm not an SDHCI
> expert, so it's possible changing frequencies also needs a special operation
> to recalculate this variable. But this was making all internal calculations
> wrong when paired with this series.
>
> - With this flag set SDHCI's core now properly calculates divisor values based
> on whatever clock frequency I set in DT. And guess what, the issue reappears
> even when running on 150MHz. It turns out, as I had some debugging enabled,
> the issue only happens when the controller is configured at 100KHz (that
> only happens while running the card detect thread).
>
> So, I can now do this (note that for card detection try to communicate with the
> card starting at 400KHz down to 100KHz in 100KHz steps):
>
> ----->8-----
>
> diff --git a/drivers/mmc/host/sdhci-iproc.c b/drivers/mmc/host/sdhci-iproc.c
> index 536c382e2486..e5a5de63f347 100644
> --- a/drivers/mmc/host/sdhci-iproc.c
> +++ b/drivers/mmc/host/sdhci-iproc.c
> @@ -173,6 +173,11 @@ static unsigned int sdhci_iproc_get_max_clock(struct sdhci_host *host)
> return pltfm_host->clock;
> }
>
> +static unsigned int sdhci_iproc_bcm2711_get_min_clock(struct sdhci_host *host)
> +{
> + return 200000;
> +}
> +
> static const struct sdhci_ops sdhci_iproc_ops = {
> .set_clock = sdhci_set_clock,
> .get_max_clock = sdhci_iproc_get_max_clock,
> @@ -271,13 +276,15 @@ static const struct sdhci_ops sdhci_iproc_bcm2711_ops = {
> .set_clock = sdhci_set_clock,
> .set_power = sdhci_set_power_and_bus_voltage,
> .get_max_clock = sdhci_iproc_get_max_clock,
> + .get_min_clock = sdhci_iproc_bcm2711_get_min_clock,
> .set_bus_width = sdhci_set_bus_width,
> .reset = sdhci_reset,
> .set_uhs_signaling = sdhci_set_uhs_signaling,
> };
>
> ----->8-----
>
> Which is rather nicer than what this series introduces. But I can't still
> explain why configuring the controller at 100KHz is causing the hangs (while
> having the core clock setup at 500MHz), and I'm not sure if excluding 100KHz
> from the polling frequency list is going to break support for older SD cards.

Thanks for your investigations. Yes, this looks much cleaner to me.

>
> Regards,
> Nicolas
>
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

\
 
 \ /
  Last update: 2021-03-26 17:44    [W:0.095 / U:0.836 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site