lkml.org 
[lkml]   [2021]   [Feb]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 2/2] usb: misc: usb5744: Add support for USB hub controller
Date


On 2/9/21 11:03 AM, Greg Kroah-Hartman wrote:
> On Tue, Feb 09, 2021 at 10:53:20AM +0100, Michal Simek wrote:
>> From: Piyush Mehta <piyush.mehta@xilinx.com>
>>
>> This patch adds a USB GPIO based hub reset for USB5744 hub. This usb5744
>> driver trigger hub reset signal after soft reset or core Reset. The HUB
>> needs to be resetted after completion of phy initialization. After the
>> toggling of gpio, hub configure using i2c usb attached command.
>>
>> USB5744 hub can be used without any I2C connection, is handled by a
>> simple platform device driver.
>>
>> As part of the reset, sets the direction of the pin to output before
>> toggling the pin. Delay of millisecond is added in between low and
>> high to meet the setup and hold time requirement of the reset.
>>
>> Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
>> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
>> ---
>>
>> MAINTAINERS | 1 +
>> drivers/usb/misc/Kconfig | 9 +++
>> drivers/usb/misc/Makefile | 1 +
>> drivers/usb/misc/usb5744.c | 115 +++++++++++++++++++++++++++++++++++++
>> 4 files changed, 126 insertions(+)
>> create mode 100644 drivers/usb/misc/usb5744.c
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 7439471b5d37..56d1fcdd24f6 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -2706,6 +2706,7 @@ F: drivers/edac/synopsys_edac.c
>> F: drivers/i2c/busses/i2c-cadence.c
>> F: drivers/i2c/busses/i2c-xiic.c
>> F: drivers/mmc/host/sdhci-of-arasan.c
>> +F: drivers/usb/misc/usb5744.c
>> N: zynq
>> N: xilinx
>>
>> diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig
>> index 8f1144359012..30335b5c4f88 100644
>> --- a/drivers/usb/misc/Kconfig
>> +++ b/drivers/usb/misc/Kconfig
>> @@ -242,6 +242,15 @@ config USB_HUB_USB251XB
>> parameters may be set in devicetree or platform data.
>> Say Y or M here if you need to configure such a device via SMBus.
>>
>> +config USB_USB5744
>> + tristate "Microchip USB5744 Hub driver"
>> + depends on I2C
>> + depends on GPIOLIB
>> + help
>> + This option enables support for Microchip USB5744 Hub. This driver
>> + optionally reset the hub using gpio pin and configure hub via i2c if
>> + connected.
>> +
>> config USB_HSIC_USB3503
>> tristate "USB3503 HSIC to USB20 Driver"
>> depends on I2C
>> diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile
>> index 5f4e598573ab..5920146a506a 100644
>> --- a/drivers/usb/misc/Makefile
>> +++ b/drivers/usb/misc/Makefile
>> @@ -25,6 +25,7 @@ obj-$(CONFIG_USB_USS720) += uss720.o
>> obj-$(CONFIG_USB_SEVSEG) += usbsevseg.o
>> obj-$(CONFIG_USB_YUREX) += yurex.o
>> obj-$(CONFIG_USB_HUB_USB251XB) += usb251xb.o
>> +obj-$(CONFIG_USB_USB5744) += usb5744.o
>
> Can you follow the convention of the config options we have already, and
> make this USB_HUB_USB5744 please?

Sure.

>
>> obj-$(CONFIG_USB_HSIC_USB3503) += usb3503.o
>> obj-$(CONFIG_USB_HSIC_USB4604) += usb4604.o
>
> And then put it in sorted order :)

Do you want me to sort the whole Makefile and Kconfig as separate patch?
It is pretty much unsorted now.

And any other problem with the driver itself?

Thanks,
Michal

\
 
 \ /
  Last update: 2021-02-09 11:27    [W:2.470 / U:0.024 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site