lkml.org 
[lkml]   [2021]   [Feb]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject[PATCH v3 00/15] introduce a generic IOCTL interface for RPMsg channels management
Date
This series restructures the RPMsg char driver to decorrelate the control part and to
create a generic RPMsg ioctl interface compatible with other RPMsg services.

The V3 is based on the guideline proposed by Mathieu Poirier to keep as much as possible
the legacy implementation of the rpmsg_char used by the GLINK and SMD platforms.


Objectives of the series:
- Allow to create a service from Linux user application:
- with a specific name
- with or without name service announcement.
- Allow to probe the same service by receiving either a NS announcement from the remote firmware
or a Linux user application request.
- Use these services independently of the RPMsg transport implementation (e.g be able to use
RPMSg char with the RPMsg virtio bus).

Steps in the series:
- Extract the control part of the char dev and create the rpmsg_ctrl.c file (patches 1 to 5)
- Enable the use of the chardev with the virtio backend (patches 6 to 10)
- Introduce the RPMSG_CREATE_DEV_IOCTL IOCTL to instantiate RPMsg devices (patch 11)
The application can then create or release a channel by specifying:
- the name service of the device to instantiate.
- the source address.
- the destination address.
- Instantiate the /dev/rpmsg interface on remote NS announcement (patches 12 to 15)

In this revision, I do not divide the series into several parts in order to show a complete
picture of the proposed evolution. To simplify the review, as a next step, I can send it in
several steps listed above.

Known current Limitations:
- Tested only with virtio RPMsg bus. The glink and smd drivers adaptations have not been tested
(not able to test it).
- For the virtio backend: No NS announcement is sent to the remote processor if the source
address is set to RPMSG_ADDR_ANY.
- For the virtio backend: the existing RPMSG_CREATE_EPT_IOCTL is working but the endpoints are
not attached to an exiting channel.

This series can be tested on top of the v5.11-rc5 (6ee1d745b7c9).

This series can be tested using rpmsgexport, rpmsgcreatedev and ping tools available here:
https://github.com/arnopo/rpmsgexport.git

Reference to the V2 discussion thread: https://lkml.org/lkml/2020/12/22/207

Arnaud Pouliquen (15):
rpmsg: char: rename rpmsg_char_init to rpmsg_chrdev_init
rpmsg: move RPMSG_ADDR_ANY in user API and document the API
rpmsg: char: export eptdev create an destroy functions
rpmsg: char: dissociate the control device from the rpmsg class
rpmsg: move the rpmsg control device from rpmsg_char to rpmsg_ctrl
rpmsg: update rpmsg_chrdev_register_device function
rpmsg: virtio: probe the rpmsg_ctrl device
rpmsg: glink: add sendto and trysendto ops
rpmsg: smd: add sendto and trysendto ops
rpmsg: char: use sendto to specify the message destination address
rpmsg: ctrl: introduce RPMSG_CREATE_DEV_IOCTL
rpmsg: char: introduce __rpmsg_chrdev_create_eptdev function
rpmsg: char: introduce a RPMsg driver for the RPmsg char device
rpmsg: char: no dynamic endpoint management for the default one
rpmsg: char: return an error if device already open

drivers/rpmsg/Kconfig | 9 ++
drivers/rpmsg/Makefile | 1 +
drivers/rpmsg/qcom_glink_native.c | 18 ++-
drivers/rpmsg/qcom_smd.c | 18 ++-
drivers/rpmsg/rpmsg_char.c | 237 +++++++++++-----------------
drivers/rpmsg/rpmsg_char.h | 51 ++++++
drivers/rpmsg/rpmsg_ctrl.c | 247 ++++++++++++++++++++++++++++++
drivers/rpmsg/rpmsg_internal.h | 10 +-
drivers/rpmsg/virtio_rpmsg_bus.c | 37 ++++-
include/linux/rpmsg.h | 3 +-
include/uapi/linux/rpmsg.h | 18 ++-
11 files changed, 483 insertions(+), 166 deletions(-)
create mode 100644 drivers/rpmsg/rpmsg_char.h
create mode 100644 drivers/rpmsg/rpmsg_ctrl.c

--
2.17.1

\
 
 \ /
  Last update: 2021-02-04 09:47    [W:0.106 / U:0.140 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site