lkml.org 
[lkml]   [2021]   [Feb]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    Date
    From
    SubjectRe: [PATCH 01/16] media: i2c: rdacm20: Enable noise immunity
    Hi Jacopo,

    Thank you for the patch.

    On Wed, Feb 17, 2021 at 12:55:19PM +0000, Kieran Bingham wrote:
    > On 16/02/2021 17:41, Jacopo Mondi wrote:
    > > Enable the noise immunity threshold at the end of the rdacm20
    > > initialization routine.
    > >
    > > The rdcam20 camera module has been so far tested with a startup

    s/rdcam20/rdacm20/

    > > delay that allowed the embedded MCU to program the serializer. If
    > > the initialization routine is run before the MCU programs the
    > > serializer and the image sensor and their addresses gets changed
    > > by the rdacm20 driver it is required to manually enable the noise
    > > immunity threshold to make the communication on the control channel
    > > more reliable.
    >
    > Oh, this is interesting, ... booting up without the delays would be ...
    > much nicer.

    I second that, but I'm a bit worried. The MCU has caused us more pain
    than gain, the best way to fix it may be with a desoldering station ;-)
    Jokes aside, if we want to start initializing with the serializer before
    the MCU completes its initialization, then we'll have a racy process,
    with two I2C masters configuring the same device. I don't think anything
    good can come out of that :-S

    Taking into account the fact that on some platforms we'll want to
    implement power management for the cameras, disabling power (possibly
    individually) when the cameras are not in use, we'll have to handle the
    race carefully, and I'm not sure there any other way than waiting for
    the camera to be initialized with an initialization delay after power
    up.

    Based on this, I'm not concerned about this patch in particular, but
    potentially about the series as a whole. I'll comment on individual
    patches as applicable.

    Regarding this patch, doies the MCU enable high threshold for the
    reverse channel as part of its initialization procedure ? Do we have a
    full list of what it configures in the MAX9271 ? If so, could we capture
    it in a comment in the driver ? That would be very helpful as a
    reference.

    > > Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
    > > ---
    > > drivers/media/i2c/rdacm20.c | 8 +++++++-
    > > 1 file changed, 7 insertions(+), 1 deletion(-)
    > >
    > > diff --git a/drivers/media/i2c/rdacm20.c b/drivers/media/i2c/rdacm20.c
    > > index 90eb73f0e6e9..f7fd5ae955d0 100644
    > > --- a/drivers/media/i2c/rdacm20.c
    > > +++ b/drivers/media/i2c/rdacm20.c
    > > @@ -541,7 +541,13 @@ static int rdacm20_initialize(struct rdacm20_device *dev)
    > >
    > > dev_info(dev->dev, "Identified MAX9271 + OV10635 device\n");
    > >
    > > - return 0;
    > > + /*
    > > + * Set reverse channel high threshold to increase noise immunity.
    > > + *
    > > + * This should be compensated by increasing the reverse channel
    > > + * amplitude on the remote deserializer side.
    > > + */
    > > + return max9271_set_high_threshold(&dev->serializer, true);
    >
    > Does this work 'out of the box' ? I.e. if this patch is applied, I
    > assume it is required to remove the regulator delays that I/we have in DT?
    >
    > Likewise, does that note mean this patch must also be accompanied by the
    > update in max9286 somehow?
    >
    > I guess we can't keep 'test bisectability' with this very easily so it
    > probably doesn't matter too much, the end result will be the interesting
    > part.
    >
    > Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
    >
    > > }
    > >
    > > static int rdacm20_probe(struct i2c_client *client)

    --
    Regards,

    Laurent Pinchart

    \
     
     \ /
      Last update: 2021-02-22 01:52    [W:2.218 / U:0.028 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site