lkml.org 
[lkml]   [2021]   [Feb]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2 5/5] iio: dac: ad5686: Add PWM as a trigger source
On Thu, Feb 18, 2021 at 5:31 PM Rob Herring <robh+dt@kernel.org> wrote:
>
> On Thu, Feb 18, 2021 at 8:05 AM Jonathan Cameron <jic23@kernel.org> wrote:
> >
> > On Wed, 17 Feb 2021 10:34:38 +0200
> > Alexandru Ardelean <alexandru.ardelean@analog.com> wrote:
> >
> > > From: Mircea Caprioru <mircea.caprioru@analog.com>
> > >
> > > A PWM signal will be used as a trigger source to have a deterministic
> > > sampling frequency since this family of DAC has no hardware interrupt
> > > source.
> > >
> > > This feature is made optional however, as there are some board setups where
> > > this isn't used.
> > >
> >
> > So this is taking a very generic setup, but then implementing it
> > as a bit of a hack within the driver.
> >
> > It's effectively a PWM connected up to an instance
> > of iio/triggers/iio-trig-interrupt.c
> >
> > Now, I've not looked at that trigger driver for a while, so you may well
> > need to figure out how to add a binding to instantiate it.
> > (looks like no one has used it since board file days, or via instantiation
> > from another driver).
> >
> > It's a slightly odd corner case as what it reflects is that we have
> > an interrupt available that is intended to drive some sort of data
> > capture or output (it's a trigger signal) - but exactly what is done
> > is a runtime configurable. In this particular case that interrupt
> > is hooked up to a PWM and we also want to represent that.
> >
> > The fact it's being driven via a PWM is interesting but we should be
> > able to extend that trigger driver to optionally accept a pwm provider
> > and if it has one provide frequency control.
> >

So, the main intent here was to provide a user for this new output kfifo.
I don't think I have time to re-spin this into a proper solution.
Someone else may come about and do it.

I'll drop this from the series [for now].

> > Binding might look something like the following..
> >
> > interrupt-trigger {
> > interrupts = <>;
> > pwms = <&pwm 0 4000 PWM_POLARITY_INVERTED>;
> > };
> >
> > @Rob, what do you think of this odd beast?
>
> So a PWM routed back to a GPIO interrupt? It needs a compatible, but
> otherwise I wouldn't object to the binding if that's what the h/w
> looks like. But from an OS perspective, I don't think you need it.
>
> > So all in all, this generic facility needs a generic implementation, not
> > one buried in a driver.
> >
> > Another open question here is whether you really can't just use an hrtimer
> > to get similar precision? Way back at the dawn of time in IIO we had
> > code to use the RTC periodic ticks as a trigger with the theory that they
> > would give very precise and even timing. In the end it turned out that
> > hrtimers worked just as well (and RTCs drivers emulated the periodic
> > ticks via hrtimers, dropping their use of the hardware periodic timers).
>
> +100
>
> A hrtimer is likely going to be more precise. IIRC, timers are
> serviced first. Either way, you're going to have some amount of
> interrupt service latency, so any precision you think you are gaining
> by 'doing it in h/w' isn't really there.
>
> Rob

\
 
 \ /
  Last update: 2021-02-19 09:53    [W:0.082 / U:0.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site