lkml.org 
[lkml]   [2021]   [Feb]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v3 2/2] serial: 8250: Add new 8250-core based Broadcom STB driver
From
Date


On 2/12/2021 11:57 AM, Al Cooper wrote:
> Add a UART driver for the new Broadcom 8250 based STB UART. The new
> UART is backward compatible with the standard 8250, but has some
> additional features. The new features include a high accuracy baud
> rate clock system and DMA support.
>
> The driver will use the new optional BAUD MUX clock to select the best
> one of the four master clocks (81MHz, 108MHz, 64MHz and 48MHz) to feed
> the baud rate selection logic for any requested baud rate. This allows
> for more accurate BAUD rates when high speed baud rates are selected.
>
> The driver will use the new UART DMA hardware if the UART DMA registers
> are specified in Device Tree "reg" property.
>
> The driver also sets the UPSTAT_AUTOCTS flag when hardware flow control
> is enabled. This flag is needed for UARTs that don't assert a CTS
> changed interrupt when CTS changes and AFE (Hardware Flow Control) is
> enabled.
>
> The driver also contains a workaround for a bug in the Synopsis 8250
> core. The problem is that at high baud rates, the RX partial FIFO
> timeout interrupt can occur but there is no RX data (DR not set in
> the LSR register). In this case the driver will not read the Receive
> Buffer Register, which clears the interrupt, and the system will get
> continuous UART interrupts until the next RX character arrives. The
> fix originally suggested by Synopsis was to read the Receive Buffer
> Register and discard the character when the DR bit in the LSR was
> not set, to clear the interrupt. The problem was that occasionally
> a character would arrive just after the DR bit check and a valid
> character would be discarded. The fix that was added will clear
> receive interrupts to stop the interrupt, deassert RTS to insure
> that no new data can arrive, wait for 1.5 character times for the
> sender to react to RTS and then check for data and either do a dummy
> read or a valid read. Sysfs error counters were also added and were
> used to help create test software that would cause the error condition.
> The counters can be found at:
> /sys/devices/platform/rdb/*serial/rx_bad_timeout_late_char
> /sys/devices/platform/rdb/*serial/rx_bad_timeout_no_char
>
> Signed-off-by: Al Cooper <alcooperx@gmail.com>
> ---
> MAINTAINERS | 8 +
> drivers/tty/serial/8250/8250_bcm7271.c | 1099 ++++++++++++++++++++++++
> drivers/tty/serial/8250/Kconfig | 11 +
> drivers/tty/serial/8250/Makefile | 1 +
> drivers/tty/serial/8250/bcm7271_uart.h | 158 ++++
> 5 files changed, 1277 insertions(+)
> create mode 100644 drivers/tty/serial/8250/8250_bcm7271.c
> create mode 100644 drivers/tty/serial/8250/bcm7271_uart.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 64c7169db617..bb6ad2fc4376 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -3582,6 +3582,14 @@ S: Supported
> F: Documentation/devicetree/bindings/i2c/brcm,brcmstb-i2c.yaml
> F: drivers/i2c/busses/i2c-brcmstb.c
>
> +BROADCOM BRCMSTB UART DRIVER
> +M: Al Cooper <alcooperx@gmail.com>
> +L: linux-usb@vger.kernel.org

This should probably be linux-serial, copy pasted from the USB entry
down below presumably.
--
Florian

\
 
 \ /
  Last update: 2021-02-12 21:49    [W:0.051 / U:0.540 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site