lkml.org 
[lkml]   [2021]   [Nov]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 1/5] dt-bindings: soc: samsung: Add Exynos USI bindings
Date
Add constants for choosing USIv2 configuration mode in device tree.
Those are further used in USI driver to figure out which value to write
into SW_CONF register. Also document USIv2 IP-core bindings.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
---
Changes in v2:
- Combined dt-bindings doc and dt-bindings header patches
- Added i2c node to example in bindings doc
- Added mentioning of shared internal circuits
- Added USI_V2_NONE value to bindings header

.../bindings/soc/samsung/exynos-usi.yaml | 135 ++++++++++++++++++
include/dt-bindings/soc/samsung,exynos-usi.h | 17 +++
2 files changed, 152 insertions(+)
create mode 100644 Documentation/devicetree/bindings/soc/samsung/exynos-usi.yaml
create mode 100644 include/dt-bindings/soc/samsung,exynos-usi.h

diff --git a/Documentation/devicetree/bindings/soc/samsung/exynos-usi.yaml b/Documentation/devicetree/bindings/soc/samsung/exynos-usi.yaml
new file mode 100644
index 000000000000..a822bc62b3cd
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/samsung/exynos-usi.yaml
@@ -0,0 +1,135 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/samsung/exynos-usi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung's Exynos USI (Universal Serial Interface) binding
+
+maintainers:
+ - Sam Protsenko <semen.protsenko@linaro.org>
+ - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+
+description: |
+ USI IP-core provides selectable serial protocol (UART, SPI or High-Speed I2C).
+ USI shares almost all internal circuits within each protocol, so only one
+ protocol can be chosen at a time. USI is modeled as a node with zero or more
+ child nodes, each representing a serial sub-node device. The mode setting
+ selects which particular function will be used.
+
+ Refer to next bindings documentation for information on protocol subnodes that
+ can exist under USI node:
+
+ [1] Documentation/devicetree/bindings/serial/samsung_uart.yaml
+ [2] Documentation/devicetree/bindings/i2c/i2c-exynos5.txt
+ [3] Documentation/devicetree/bindings/spi/spi-samsung.txt
+
+properties:
+ $nodename:
+ pattern: "^usi@[0-9a-f]+$"
+
+ compatible:
+ const: samsung,exynos-usi-v2
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Bus (APB) clock
+ - description: Operating clock for UART/SPI/I2C protocol
+
+ clock-names:
+ items:
+ - const: pclk
+ - const: ipclk
+
+ ranges: true
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 1
+
+ samsung,sysreg:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ description:
+ Should be phandle/offset pair. The phandle to System Register syscon node
+ (for the same domain where this USI controller resides) and the offset
+ of SW_CONF register for this USI controller.
+
+ samsung,mode:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Selects USI function (which serial protocol to use). Refer to
+ <include/dt-bindings/soc/samsung,exynos-usi.h> for valid USI mode values.
+
+ samsung,clkreq-on:
+ type: boolean
+ description:
+ Enable this property if underlying protocol requires the clock to be
+ continuously provided without automatic gating. As suggested by SoC
+ manual, it should be set in case of SPI/I2C slave, UART Rx and I2C
+ multi-master mode. Usually this property is needed if USI mode is set
+ to "UART".
+
+ This property is optional.
+
+patternProperties:
+ # All other properties should be child nodes
+ "^.*@[0-9a-f]+$":
+ type: object
+ description: Child node describing underlying USI serial protocol
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - ranges
+ - "#address-cells"
+ - "#size-cells"
+ - samsung,sysreg
+ - samsung,mode
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/soc/samsung,exynos-usi.h>
+
+ usi0: usi@138200c0 {
+ compatible = "samsung,exynos-usi-v2";
+ reg = <0x138200c0 0x20>;
+ samsung,sysreg = <&sysreg_peri 0x1010>;
+ samsung,mode = <USI_V2_UART>;
+ samsung,clkreq-on; /* needed for UART mode */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ clocks = <&cmu_peri 32>, <&cmu_peri 31>;
+ clock-names = "pclk", "ipclk";
+ status = "disabled";
+
+ serial_0: serial@13820000 {
+ compatible = "samsung,exynos850-uart";
+ reg = <0x13820000 0xc0>;
+ interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cmu_peri 32>, <&cmu_peri 31>;
+ clock-names = "uart", "clk_uart_baud0";
+ status = "disabled";
+ };
+
+ hsi2c_0: i2c@13820000 {
+ compatible = "samsung,exynosautov9-hsi2c";
+ reg = <0x13820000 0xc0>;
+ interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&cmu_peri 32>, <&cmu_peri 31>;
+ clock-names = "hsi2c_pclk", "hsi2c";
+ status = "disabled";
+ };
+ };
diff --git a/include/dt-bindings/soc/samsung,exynos-usi.h b/include/dt-bindings/soc/samsung,exynos-usi.h
new file mode 100644
index 000000000000..a01af169d249
--- /dev/null
+++ b/include/dt-bindings/soc/samsung,exynos-usi.h
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (c) 2021 Linaro Ltd.
+ * Author: Sam Protsenko <semen.protsenko@linaro.org>
+ *
+ * Device Tree bindings for Samsung Exynos USI (Universal Serial Interface).
+ */
+
+#ifndef __DT_BINDINGS_SAMSUNG_EXYNOS_USI_H
+#define __DT_BINDINGS_SAMSUNG_EXYNOS_USI_H
+
+#define USI_V2_NONE 0
+#define USI_V2_UART 1
+#define USI_V2_SPI 2
+#define USI_V2_I2C 3
+
+#endif /* __DT_BINDINGS_SAMSUNG_EXYNOS_USI_H */
--
2.30.2
\
 
 \ /
  Last update: 2021-11-30 03:23    [W:0.027 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site