lkml.org 
[lkml]   [2021]   [Nov]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v6 6/8] MIPS: DTS: CI20: Add DT nodes for HDMI setup
Hi Nikolaus, Thomas,

Le mer., nov. 10 2021 at 20:43:31 +0100, H. Nikolaus Schaller
<hns@goldelico.com> a écrit :
> From: Paul Boddie <paul@boddie.org.uk>
>
> We need to hook up
> * HDMI connector
> * HDMI power regulator
> * JZ4780_CLK_HDMI @ 27 MHz
> * DDC pinmux
> * HDMI and LCDC endpoint connections
>
> Signed-off-by: Paul Boddie <paul@boddie.org.uk>
> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
> ---
> arch/mips/boot/dts/ingenic/ci20.dts | 73
> +++++++++++++++++++++++++++--
> 1 file changed, 70 insertions(+), 3 deletions(-)
>
> diff --git a/arch/mips/boot/dts/ingenic/ci20.dts
> b/arch/mips/boot/dts/ingenic/ci20.dts
> index a688809beebca..a62557bede565 100644
> --- a/arch/mips/boot/dts/ingenic/ci20.dts
> +++ b/arch/mips/boot/dts/ingenic/ci20.dts
> @@ -78,6 +78,18 @@ eth0_power: fixedregulator@0 {
> enable-active-high;
> };
>
> + hdmi_out: connector {
> + compatible = "hdmi-connector";
> + label = "HDMI OUT";
> + type = "a";
> +
> + port {
> + hdmi_con: endpoint {
> + remote-endpoint = <&dw_hdmi_out>;
> + };
> + };
> + };
> +
> ir: ir {
> compatible = "gpio-ir-receiver";
> gpios = <&gpe 3 GPIO_ACTIVE_LOW>;
> @@ -102,6 +114,17 @@ otg_power: fixedregulator@2 {
> gpio = <&gpf 14 GPIO_ACTIVE_LOW>;
> enable-active-high;
> };
> +
> + hdmi_power: fixedregulator@3 {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "hdmi_power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> +
> + gpio = <&gpa 25 GPIO_ACTIVE_LOW>;

Just use 0 instead of GPIO_ACTIVE_LOW, since the flag is simply ignored
(I know the other regulators do use it, but I'll clean that up soon).

> + enable-active-high;
> + };
> };
>
> &ext {
> @@ -113,9 +136,9 @@ &cgu {
> * Use the 32.768 kHz oscillator as the parent of the RTC for a
> higher
> * precision.
> */
> - assigned-clocks = <&cgu JZ4780_CLK_OTGPHY>, <&cgu JZ4780_CLK_RTC>;
> - assigned-clock-parents = <0>, <&cgu JZ4780_CLK_RTCLK>;
> - assigned-clock-rates = <48000000>;
> + assigned-clocks = <&cgu JZ4780_CLK_OTGPHY>, <&cgu JZ4780_CLK_RTC>,
> <&cgu JZ4780_CLK_HDMI>;
> + assigned-clock-parents = <0>, <&cgu JZ4780_CLK_RTCLK>, <0>;
> + assigned-clock-rates = <48000000>, <0>, <27000000>;

So drm-misc-next is based on a slightly older version (not v5.16-rc1
yet), and these lines changed in linux master.

I think it would make sense to merge the DT changes (+ doc) into the
MIPS tree, and the driver changes into drm-misc-next.

@Thomas: Is that OK for you?

Cheers,
-Paul

> };
>
> &tcu {
> @@ -506,6 +529,12 @@ pins_i2c4: i2c4 {
> bias-disable;
> };
>
> + pins_hdmi_ddc: hdmi_ddc {
> + function = "hdmi-ddc";
> + groups = "hdmi-ddc";
> + bias-disable;
> + };
> +
> pins_nemc: nemc {
> function = "nemc";
> groups = "nemc-data", "nemc-cle-ale", "nemc-rd-we", "nemc-frd-fwe";
> @@ -536,3 +565,41 @@ pins_mmc1: mmc1 {
> bias-disable;
> };
> };
> +
> +&hdmi {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pins_hdmi_ddc>;
> +
> + hdmi-5v-supply = <&hdmi_power>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + dw_hdmi_in: endpoint {
> + remote-endpoint = <&lcd_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + dw_hdmi_out: endpoint {
> + remote-endpoint = <&hdmi_con>;
> + };
> + };
> + };
> +};
> +
> +&lcdc0 {
> + status = "okay";
> +
> + port {
> + lcd_out: endpoint {
> + remote-endpoint = <&dw_hdmi_in>;
> + };
> + };
> +};
> --
> 2.33.0
>


\
 
 \ /
  Last update: 2021-11-16 00:30    [W:0.104 / U:0.644 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site