lkml.org 
[lkml]   [2021]   [Oct]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 1/5] PCI/switchtec: Error out MRPC execution when no GAS access
Date
On Wed, 2021-10-06 at 15:20 -0500, Bjorn Helgaas wrote:
> On Wed, Oct 06, 2021 at 07:00:55PM +0000, Kelvin.Cao@microchip.com
> wrote:
> > On Wed, 2021-10-06 at 09:19 -0500, Bjorn Helgaas wrote:
> > > On Wed, Oct 06, 2021 at 05:49:29AM +0000,
> > > Kelvin.Cao@microchip.com
> > > wrote:
> > > > On Tue, 2021-10-05 at 21:33 -0500, Bjorn Helgaas wrote:
> > > > > On Wed, Oct 06, 2021 at 12:37:02AM +0000,
> > > > > Kelvin.Cao@microchip.com
> > > > > wrote:
> > > > > > On Tue, 2021-10-05 at 15:11 -0500, Bjorn Helgaas wrote:
> > > > > > > On Mon, Oct 04, 2021 at 08:51:06PM +0000,
> > > > > > > Kelvin.Cao@microchip.com
> > > > > > > wrote:
> > > > > > > > On Sat, 2021-10-02 at 10:11 -0500, Bjorn Helgaas wrote:
> > > > > > > > > I *thought* the problem was that the PCIe Memory Read
> > > > > > > > > failed and the Root Complex fabricated ~0 data to
> > > > > > > > > complete
> > > > > > > > > the CPU read. But now I'm not sure, because it
> > > > > > > > > sounds
> > > > > > > > > like it might be that the PCIe transaction succeeds,
> > > > > > > > > but
> > > > > > > > > it reads data that hasn't been updated by the
> > > > > > > > > firmware,
> > > > > > > > > i.e., it reads 'in progress' because firmware hasn't
> > > > > > > > > updated it to 'done'.
> > > > > > > >
> > > > > > > > The original message was sort of misleading. After a
> > > > > > > > firmware reset, CPU getting ~0 for the PCIe Memory Read
> > > > > > > > doesn't explain the hang. In a MRPC execution (DMA
> > > > > > > > MRPC
> > > > > > > > mode), the MRPC status which is located in the host
> > > > > > > > memory,
> > > > > > > > gets initialized by the CPU and updated/finalized by
> > > > > > > > the
> > > > > > > > firmware. In the situation of a firmware reset, any
> > > > > > > > MRPC
> > > > > > > > initiated afterwards will not get the status updated by
> > > > > > > > the
> > > > > > > > firmware per the reason you pointed out above (or
> > > > > > > > similar,
> > > > > > > > to my understanding, firmware can no longer DMA data to
> > > > > > > > host
> > > > > > > > memory in such cases), therefore the MRPC execution
> > > > > > > > will
> > > > > > > > never end.
> > > > > > >
> > > > > > > I'm glad this makes sense to you, because it still
> > > > > > > doesn't to
> > > > > > > me.
> > > > > > >
> > > > > > > check_access() does an MMIO read to something in
> > > > > > > BAR0. If
> > > > > > > that read returns ~0, it means either the PCIe Memory
> > > > > > > Read
> > > > > > > was
> > > > > > > successful and the Switchtec device supplied ~0 data
> > > > > > > (maybe
> > > > > > > because firmware has not initialized that part of the
> > > > > > > BAR) or
> > > > > > > the PCIe Memory Read failed and the root complex
> > > > > > > fabricated
> > > > > > > the ~0 data.
> > > > > > >
> > > > > > > I'd like to know which one is happening so we can clarify
> > > > > > > the
> > > > > > > commit log text about "MRPC command executions hang
> > > > > > > indefinitely" and "host wil fail all GAS reads." It's
> > > > > > > not
> > > > > > > clear whether these are PCIe protocol issues or
> > > > > > > driver/firmware interaction issues.
> > > > > >
> > > > > > I think it's the latter case, the ~0 data was fabricated by
> > > > > > the
> > > > > > root complex, as the MMIO read in check_access() always
> > > > > > returns
> > > > > > ~0 until a reboot or a rescan happens.
> > > > >
> > > > > If the root complex fabricates ~0, that means a PCIe
> > > > > transaction
> > > > > failed, i.e., the device didn't respond. Rescan only does
> > > > > config
> > > > > reads and writes. Why should that cause the PCIe
> > > > > transactions to
> > > > > magically start working?
> > > >
> > > > I took a closer look. What I observed was like this. A firmware
> > > > reset cleared some CSR settings including the MSE and MBE bits
> > > > and
> > > > the Base Address Registers. With a rescan (removing the switch
> > > > to
> > > > which the management EP was binded from root port and rescan),
> > > > the
> > > > management EP was re-enumerated and driver was re-probed, so
> > > > that
> > > > the settings cleared by the firmware reset was properly setup
> > > > again,
> > > > therefore PCIe transactions start working.
> > >
> > > I think what you just said is that
> > >
> > > - the driver asked the firmware to reset the device
> > >
> > > - the firmware did reset the device, which cleared Memory Space
> > > Enable
> > >
> > > - nothing restored the device config after the reset, so Memory
> > > Space Enable remains cleared
> > >
> > > - the driver does MMIO reads to figure out when the reset has
> > > completed
> > >
> > > - the device doesn't respond to the PCIe Memory Reads because
> > > Memory
> > > Space Enable is cleared
> > >
> > > - the root complex sees a timeout or error completion and
> > > fabricates
> > > ~0 data for the CPU read
> > >
> > > - the driver sees ~0 data from the MMIO read and thinks the
> > > device
> > > or firmware is hung
> > >
> > > If that's all true, I think the patch is sort of a band-aid that
> > > doesn't fix the problem at all but only makes the driver's
> > > response
> > > to
> > > it marginally better. But the device is still unusable until a
> > > rescan
> > > or reboot.
> > >
> > > So I think we should drop this patch and do something to restore
> > > the
> > > device state after the reset.
> >
> > Do you mean we should do something at the driver level to
> > automatically
> > try to restore the device state after the reset? I was thinking
> > it's up
> > to the user to make the call to restore the device state or take
> > other
> > actions, so that returning an error code from MRPC to indicate what
> > happened would be good enough for the driver.
>
> It sounds like this is a completely predictable situation. Why would
> you want manual user intervention?
>
> I'm pretty sure there are drivers that save state *before* the reset
> and restore it afterwards.

Sometimes it's not predicatable. We have various interfaces to talk to
the firmware, like in-band, UART, TWI, etc. If a firmware reset is
issued to the firmware via the TWI sideband interface from BMC, neither
the host utility which might be periodically issueing MRPC commands to
monitor the switch nor the driver will be aware of this.

If the reset command is issued via the driver, as it's just another
MRPC command initiated by a user space process, the driver doesn't
actually know what will be happening unless it decodes each MRPC it
forwards to the firmware and checks for the reset command, but I doubt
it's something the driver should do.

>
> > Can you possibly shed light on what might be a reasonable way to
> > restore the device state in the driver if applicable? I was just
> > doing
> > it by leveraging the remove and rescan interfaces in the sysfs.
> >
> > That's all true. I lean towards keeping the patch as I think making
> > the
> > response better under the following situations might not be bad.
> >
> > - The firmware reset case, as we discussed. I'd think it's still
> > useful for users to get a fast error return which indicates
> > something
> > bad happened and some actions need to be taken either to abort or
> > try
> > to recover. In this case, we are assuming that a firmware reset
> > will
> > boot the firmware successfully.
>
> So wait, you mean you just intentionally ask the firmware to reset,
> knowing that the device will be unusable until the user reboots or
> does a manual rescan? And the way to improve this is for the driver
> to report an error to the user instead of hanging? I *guess* that
> might be some sort of improvement, but seems like a pretty small one.

Yes, however, I believe it's something our users really like to have...
With this, they can do their user space programming/scripting more
easily in a synchronous fashion.

>
> > - The firwmare crashes and doesn't respond, which normally is the
> > reason for users to issue a firmware reset command to try to
> > recover it
> > via either the driver or a sideband interface. The firmware may not
> > be
> > able to recover by a reset in some extream situations like hardware
> > errors, so that an error return is probably all the users can get
> > before another level of recovery happens.
> >
> > So I'd think this patch is still making the driver better in some
> > way.
> >
> > Kelvin
> >
\
 
 \ /
  Last update: 2021-10-06 23:28    [W:0.084 / U:0.200 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site