lkml.org 
[lkml]   [2021]   [Oct]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 3/6] Documentation: ACPI: Document _DSC object usage for enum power state
Date
Document the use of the _DSC object for setting desirable power state
during probe.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
---
Documentation/firmware-guide/acpi/index.rst | 1 +
.../firmware-guide/acpi/non-d0-probe.rst | 78 +++++++++++++++++++
2 files changed, 79 insertions(+)
create mode 100644 Documentation/firmware-guide/acpi/non-d0-probe.rst

diff --git a/Documentation/firmware-guide/acpi/index.rst b/Documentation/firmware-guide/acpi/index.rst
index a99ee402b212b..b053b0c3d6969 100644
--- a/Documentation/firmware-guide/acpi/index.rst
+++ b/Documentation/firmware-guide/acpi/index.rst
@@ -26,5 +26,6 @@ ACPI Support
acpi-lid
lpit
video_extension
+ non-d0-probe
extcon-intel-int3496
intel-pmc-mux
diff --git a/Documentation/firmware-guide/acpi/non-d0-probe.rst b/Documentation/firmware-guide/acpi/non-d0-probe.rst
new file mode 100644
index 0000000000000..78781e1ab6a3d
--- /dev/null
+++ b/Documentation/firmware-guide/acpi/non-d0-probe.rst
@@ -0,0 +1,78 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+========================================
+Probing devices in other D states than 0
+========================================
+
+Introduction
+============
+
+In some cases it may be preferred to leave certain devices powered off for the
+entire system bootup if powering on these devices has adverse side effects,
+beyond just powering on the said device.
+
+How it works
+============
+
+The _DSC (Device State for Configuration) object that evaluates to an integer
+may be used to tell Linux the highest allowed D state for a device during
+probe. The support for _DSC requires support from the kernel bus type if the
+bus driver normally sets the device in D0 state for probe.
+
+The downside of using _DSC is that as the device is not powered on, even if
+there's a problem with the device, the driver likely probes just fine but the
+first user will find out the device doesn't work, instead of a failure at probe
+time. This feature should thus be used sparingly.
+
+I²C
+---
+
+If an I²C driver indicates its support for this by setting the
+I2C_DRV_ACPI_WAIVE_D0_PROBE flag in struct i2c_driver.flags field and the
+_DSC object evaluates to integer higher than the D state of the device,
+the device will not be powered on (put in D0 state) for probe.
+
+D states
+--------
+
+The D states and thus also the allowed values for _DSC are listed below. Refer
+to [1] for more information on device power states.
+
+.. code-block:: text
+
+ Number State Description
+ 0 D0 Device fully powered on
+ 1 D1
+ 2 D2
+ 3 D3hot
+ 4 D3cold Off
+
+References
+==========
+
+[1] https://uefi.org/specifications/ACPI/6.4/02_Definition_of_Terms/Definition_of_Terms.html#device-power-state-definitions
+
+Example
+=======
+
+An ASL example describing an ACPI device using _DSC object to tell Operating
+System the device should remain powered off during probe looks like this. Some
+objects not relevant from the example point of view have been omitted.
+
+.. code-block:: text
+
+ Device (CAM0)
+ {
+ Name (_HID, "SONY319A")
+ Name (_UID, Zero)
+ Name (_CRS, ResourceTemplate ()
+ {
+ I2cSerialBus(0x0020, ControllerInitiated, 0x00061A80,
+ AddressingMode7Bit, "\\_SB.PCI0.I2C0",
+ 0x00, ResourceConsumer)
+ })
+ Name (_DSC, 0, NotSerialized)
+ {
+ Return (0x4)
+ }
+ }
--
2.30.2
\
 
 \ /
  Last update: 2021-10-18 17:17    [W:0.068 / U:0.956 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site