lkml.org 
[lkml]   [2021]   [Oct]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 2/8] net: phy: Add 10-BaseT1L registers
Date
From: Alexandru Tachici <alexandru.tachici@analog.com>

The 802.3gc specification defines the 10-BaseT1L link
mode for ethernet trafic on twisted wire pair.

PMA status register can be used to detect if the phy supports
2.4 V TX level and PCS control register can be used to
enable/disable PCS level loopback.

Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
---
include/uapi/linux/mdio.h | 16 ++++++++++++++++
1 file changed, 16 insertions(+)

diff --git a/include/uapi/linux/mdio.h b/include/uapi/linux/mdio.h
index bdf77dffa5a4..8ae82fe3aece 100644
--- a/include/uapi/linux/mdio.h
+++ b/include/uapi/linux/mdio.h
@@ -65,6 +65,8 @@
#define MDIO_PCS_10GBRT_STAT2 33 /* 10GBASE-R/-T PCS status 2 */
#define MDIO_AN_10GBT_CTRL 32 /* 10GBASE-T auto-negotiation control */
#define MDIO_AN_10GBT_STAT 33 /* 10GBASE-T auto-negotiation status */
+#define MDIO_PMA_10T1L_STAT 2295 /* 10BASE-T1L PMA status */
+#define MDIO_PCS_10T1L_CTRL 2278 /* 10BASE-T1L PCS control */

/* LASI (Link Alarm Status Interrupt) registers, defined by XENPAK MSA. */
#define MDIO_PMA_LASI_RXCTRL 0x9000 /* RX_ALARM control */
@@ -262,6 +264,20 @@
#define MDIO_AN_10GBT_STAT_MS 0x4000 /* Master/slave config */
#define MDIO_AN_10GBT_STAT_MSFLT 0x8000 /* Master/slave config fault */

+/* 10BASE-T1L PMA status register. */
+#define MDIO_PMA_10T1L_STAT_LINK 0x0001 /* PMA receive link up */
+#define MDIO_PMA_10T1L_STAT_FAULT 0x0002 /* Fault condition detected */
+#define MDIO_PMA_10T1L_STAT_POLARITY 0x0004 /* Receive polarity is reversed */
+#define MDIO_PMA_10T1L_STAT_RECV_FAULT 0x0200 /* Able to detect fault on receive path */
+#define MDIO_PMA_10T1L_STAT_EEE 0x0400 /* PHY has EEE ability */
+#define MDIO_PMA_10T1L_STAT_LOW_POWER 0x0800 /* PMA has low-power ability */
+#define MDIO_PMA_10T1L_STAT_2V4_ABLE 0x1000 /* PHY has 2.4 Vpp operating mode ability */
+#define MDIO_PMA_10T1L_STAT_LB_ABLE 0x2000 /* PHY has loopback ability */
+
+/* 10BASE-T1L PCS control register. */
+#define MDIO_PCS_10T1L_CTRL_LB 0x4000 /* Enable PCS level loopback mode */
+#define MDIO_PCS_10T1L_CTRL_RESET 0x8000 /* PCS reset */
+
/* EEE Supported/Advertisement/LP Advertisement registers.
*
* EEE capability Register (3.20), Advertisement (7.60) and
--
2.25.1
\
 
 \ /
  Last update: 2021-10-11 16:14    [W:1.014 / U:0.024 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site