lkml.org 
[lkml]   [2021]   [Oct]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH v2 4/4] phy: freescale: pcie: initialize the imx8 pcie standalone phy driver
Date
> -----Original Message-----
> From: Lucas Stach <l.stach@pengutronix.de>
> Sent: Tuesday, September 28, 2021 4:44 PM
> To: Richard Zhu <hongxing.zhu@nxp.com>; kishon@ti.com; vkoul@kernel.org;
> robh@kernel.org; galak@kernel.crashing.org; shawnguo@kernel.org
> Cc: linux-phy@lists.infradead.org; devicetree@vger.kernel.org;
> linux-arm-kernel@lists.infradead.org; linux-kernel@vger.kernel.org;
> kernel@pengutronix.de; dl-linux-imx <linux-imx@nxp.com>
> Subject: Re: [PATCH v2 4/4] phy: freescale: pcie: initialize the imx8 pcie
> standalone phy driver
>
> Hi Richard,
>
> Am Dienstag, dem 28.09.2021 um 07:09 +0000 schrieb Richard Zhu:
> > > -----Original Message-----
> > > From: Lucas Stach <l.stach@pengutronix.de>
> > > Sent: Monday, September 27, 2021 4:43 PM
> > > To: Richard Zhu <hongxing.zhu@nxp.com>; kishon@ti.com;
> > > vkoul@kernel.org; robh@kernel.org; galak@kernel.crashing.org;
> > > shawnguo@kernel.org
> > > Cc: linux-phy@lists.infradead.org; devicetree@vger.kernel.org;
> > > linux-arm-kernel@lists.infradead.org; linux-kernel@vger.kernel.org;
> > > kernel@pengutronix.de; dl-linux-imx <linux-imx@nxp.com>
> > > Subject: Re: [PATCH v2 4/4] phy: freescale: pcie: initialize the
> > > imx8 pcie standalone phy driver
> > >
> > > Am Sonntag, dem 26.09.2021 um 15:39 +0800 schrieb Richard Zhu:
> > > > Add the standalone i.MX8 PCIe PHY driver.
> > > > Some reset bits should be manipulated between PHY configurations
> > > > and status check(internal PLL is locked or not).
> > > > So, do the PHY configuration in the phy_calibrate().
> > > > And check the PHY is ready or not in the phy_init().
> > >
> > > I would really like to see the PCIe controller driver side of this
> > > also, as it's hard to review standalone. For example I'm not sure if
> > > some of those reset bits should also be driven from the PHY driver,
> > > even if they are currently hooked up to the controller driver.
> > >
> > > Also I think the IOMUX GPR register handling belongs in the PHY
> > > driver, as it's configuring the reference clock routing.
> > >
> > [Richard Zhu] Sorry to bring inconvenience to you. I would send out
> > the v3
> >  patch-set and the i.MX8MM PCIe controller driver patches after I'm
> > back from the
> >  national holiday tomorrow(about one week).
>
> No problem. :) I'm just pointing out that I probably won't be able to invest
> more time reviewing this before I can get the full picture.
>
> > Although most of the IOMUX GPR bits are related to PHY, but there are
> > some bits are
> >  defined only for controller. For example, the device_type of the
> > controller, the clkreq#
> >  signal control in L1SS, and so on. We can't encapsulate all the GPR bits
> setting into PHY driver.
> > So, it's better to let controller driver to handle the general register bits
> manipulations.
> > How do you think about that?
>
> I still think we should split the drivers along the functional boundaries. It's
> quite confusing and probably going to be a maintenance issues when some of
> the PHY handling bits are still located in the controller driver, while we have a
> separate PHY driver.
>
> As the GPR region is handled by a regmap we should have no issues accessing
> even the same register from different drivers. So my vote is on moving the
> GPR bits related to PHY clocking to this driver.
>
[Richard Zhu] Yes, it is. I will consider to let PHY driver manipulate PHY related GPR bits.

> >
> > > >
> > > > Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
> > > > ---
> > > >  drivers/phy/freescale/Kconfig | 9 ++
> > > >  drivers/phy/freescale/Makefile | 1 +
> > > >  drivers/phy/freescale/phy-fsl-imx8-pcie.c | 167
> > > > ++++++++++++++++++++++
> > > >  3 files changed, 177 insertions(+)
> > > >  create mode 100644 drivers/phy/freescale/phy-fsl-imx8-pcie.c
> > >
> > > From what I know, there are several quite different PCIe PHYs used
> > > in the different i.MX8 variants. I'm not sure if we want to stuff them all
> into one file.
> > > I guess we should be more specific here and call this imx8m-phy, or
> > > even imx8mm-phy.
> > [Richard Zhu] Good suggestions, I think imx8m-phy is better, since the
> > i.MX8MQ/MM/MP
> >  have the similar architecture of the PCIe PHY implementation.
> >
> > >
> > > >
> > > > diff --git a/drivers/phy/freescale/Kconfig
> > > > b/drivers/phy/freescale/Kconfig index 320630ffe3cd..da078a676fbc
> > > > 100644
> > > > --- a/drivers/phy/freescale/Kconfig
> > > > +++ b/drivers/phy/freescale/Kconfig
> > > > @@ -14,3 +14,12 @@ config PHY_MIXEL_MIPI_DPHY
> > > >   help
> > > >   Enable this to add support for the Mixel DSI PHY as found
> > > >   on NXP's i.MX8 family of SOCs.
> > > > +
> > > > +config PHY_FSL_IMX8_PCIE
> > > > + tristate "Freescale i.MX8 PCIE PHY"
> > > > + depends on OF && HAS_IOMEM
> > > > + select GENERIC_PHY
> > > > + default ARCH_MXC
> > > > + help
> > > > + Enable this to add support for the PCIE PHY as found on i.MX8
> > > > + family of SOCs.
> > > > diff --git a/drivers/phy/freescale/Makefile
> > > > b/drivers/phy/freescale/Makefile index 1d02e3869b45..9fd467b58621
> > > > 100644
> > > > --- a/drivers/phy/freescale/Makefile
> > > > +++ b/drivers/phy/freescale/Makefile
> > > > @@ -1,3 +1,4 @@
> > > >  # SPDX-License-Identifier: GPL-2.0-only
> > > >  obj-$(CONFIG_PHY_FSL_IMX8MQ_USB) += phy-fsl-imx8mq-usb.o
> > > >  obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY) += phy-fsl-imx8-mipi-dphy.o
> > > > +obj-$(CONFIG_PHY_FSL_IMX8_PCIE) += phy-fsl-imx8-pcie.o
> > > > diff --git a/drivers/phy/freescale/phy-fsl-imx8-pcie.c
> > > > b/drivers/phy/freescale/phy-fsl-imx8-pcie.c
> > > > new file mode 100644
> > > > index 000000000000..ff47d6b83686
> > > > --- /dev/null
> > > > +++ b/drivers/phy/freescale/phy-fsl-imx8-pcie.c
> > > > @@ -0,0 +1,167 @@
> > > > +// SPDX-License-Identifier: GPL-2.0+
> > > > +/*
> > > > + * Copyright 2021 NXP
> > > > + */
> > > > +
> > > > +#include <linux/clk.h>
> > > > +#include <linux/io.h>
> > > > +#include <linux/iopoll.h>
> > > > +#include <linux/delay.h>
> > > > +#include <linux/module.h>
> > > > +#include <linux/phy/phy.h>
> > > > +#include <linux/platform_device.h> #include
> > > > +<dt-binding/phy/phy-fsl-imx8-pcie.h>
> > > > +
> > > > +#define IMX8MM_PCIE_PHY_CMN_REG061 0x184
> > > > +#define ANA_PLL_CLK_OUT_TO_EXT_IO_EN BIT(0)
> > > > +#define IMX8MM_PCIE_PHY_CMN_REG062 0x188
> > > > +#define ANA_PLL_CLK_OUT_TO_EXT_IO_SEL BIT(3)
> > > > +#define IMX8MM_PCIE_PHY_CMN_REG063 0x18C
> > > > +#define AUX_PLL_REFCLK_SEL_SYS_PLL GENMASK(7, 6)
> > > > +#define IMX8MM_PCIE_PHY_CMN_REG064 0x190
> > > > +#define ANA_AUX_RX_TX_SEL_TX BIT(7)
> > > > +#define ANA_AUX_RX_TERM_GND_EN BIT(3)
> > > > +#define ANA_AUX_TX_TERM BIT(2)
> > > > +#define IMX8MM_PCIE_PHY_CMN_REG065 0x194
> > > > +#define ANA_AUX_RX_TERM (BIT(7) | BIT(4))
> > > > +#define ANA_AUX_TX_LVL GENMASK(3, 0)
> > > > +#define IMX8MM_PCIE_PHY_CMN_REG75 0x1D4
> > > > +#define PCIE_PHY_CMN_REG75_PLL_DONE 0x3
> > > > +#define PCIE_PHY_TRSV_REG5 0x414
> > > > +#define PCIE_PHY_TRSV_REG5_GEN1_DEEMP 0x2D
> > > > +#define PCIE_PHY_TRSV_REG6 0x418
> > > > +#define PCIE_PHY_TRSV_REG6_GEN2_DEEMP 0xF
> > > > +
> > > > +struct imx8_pcie_phy {
> > > > + u32 refclk_pad_mode;
> > > > + void __iomem *base;
> > > > + struct clk *clk;
> > > > + struct phy *phy;
> > > > +};
> > > > +
> > > > +static int imx8_pcie_phy_init(struct phy *phy) {
> > > > + int ret;
> > > > + u32 val;
> > > > + struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy);
> > > > +
> > > > + ret = readl_poll_timeout(imx8_phy->base +
> > > IMX8MM_PCIE_PHY_CMN_REG75,
> > > > + val, val == PCIE_PHY_CMN_REG75_PLL_DONE,
> > > > + 10, 20000);
> > > > + return ret;
> > > > +}
> > > > +
> > > > +static int imx8_pcie_phy_cal(struct phy *phy) {
> > > > + u32 value, pad_mode;
> > > > + struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy);
> > > > +
> > > > + pad_mode = imx8_phy->refclk_pad_mode;
> > > > + if (pad_mode == IMX8_PCIE_REFCLK_PAD_INPUT) {
> > > > + /* Configure the pad as input */
> > > > + value = readl(imx8_phy->base +
> > > IMX8MM_PCIE_PHY_CMN_REG061);
> > > > + writel(value & ~ANA_PLL_CLK_OUT_TO_EXT_IO_EN,
> > > > + imx8_phy->base +
> IMX8MM_PCIE_PHY_CMN_REG061);
> > > > + } else if (pad_mode == IMX8_PCIE_REFCLK_PAD_OUTPUT) {
> > > > + /* Configure the PHY to output the refclock via pad */
> > > > + writel(ANA_PLL_CLK_OUT_TO_EXT_IO_EN,
> > > > + imx8_phy->base +
> IMX8MM_PCIE_PHY_CMN_REG061);
> > > > + writel(ANA_PLL_CLK_OUT_TO_EXT_IO_SEL,
> > > > + imx8_phy->base +
> IMX8MM_PCIE_PHY_CMN_REG062);
> > > > + writel(AUX_PLL_REFCLK_SEL_SYS_PLL,
> > > > + imx8_phy->base +
> IMX8MM_PCIE_PHY_CMN_REG063);
> > > > + value = ANA_AUX_RX_TX_SEL_TX | ANA_AUX_TX_TERM;
> > > > + writel(value | ANA_AUX_RX_TERM_GND_EN,
> > > > + imx8_phy->base +
> IMX8MM_PCIE_PHY_CMN_REG064);
> > > > + writel(ANA_AUX_RX_TERM | ANA_AUX_TX_LVL,
> > > > + imx8_phy->base +
> IMX8MM_PCIE_PHY_CMN_REG065);
> > > > + }
> > > > +
> > > > + /* Tune PHY de-emphasis setting to pass PCIe compliance. */
> > > > + writel(PCIE_PHY_TRSV_REG5_GEN1_DEEMP,
> > > > + imx8_phy->base + PCIE_PHY_TRSV_REG5);
> > > > + writel(PCIE_PHY_TRSV_REG6_GEN2_DEEMP,
> > > > + imx8_phy->base + PCIE_PHY_TRSV_REG6);
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static int imx8_pcie_phy_power_on(struct phy *phy) {
> > > > + struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy);
> > > > +
> > > > + return clk_prepare_enable(imx8_phy->clk);
> > >
> > > Do we need to enable this clock when the refclock is supplied
> > > externally via the pad?
> > >
> > [Richard Zhu] Good question. I think this clock is not needed anymore if the
> refclock is sourced from external OSC.
> > I just enable the PLL2_100Mhz here, since when internal PLL is used as
> refclock, the pll2_100Mhz should be turned on.
> > Shall I remove the setting and just keep the callback for further extend
> usage(internal PLL used as refclk)?
> >
> Yes, we should avoid turning on clocks that aren't needed. So the clock enable
> here should be dependent on the pad-mode. When the clock is supplied
> externally we don't want to enable the internal clock.
[Richard Zhu] How about that the dummy clock is used in the dts when "IMX8_PCIE_REFCLK_PAD_INPUT" mode is used?
Thus, we can keep driver simple and aligned, and use different dts definitions to specify different REFCLK modes.

>
> Regards,
> Lucas
>
> > > > +}
> > > > +
> > > > +static int imx8_pcie_phy_power_off(struct phy *phy) {
> > > > + struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy);
> > > > +
> > > > + clk_disable_unprepare(imx8_phy->clk);
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static const struct phy_ops imx8_pcie_phy_ops = {
> > > > + .init = imx8_pcie_phy_init,
> > > > + .calibrate = imx8_pcie_phy_cal,
> > > > + .power_on = imx8_pcie_phy_power_on,
> > > > + .power_off = imx8_pcie_phy_power_off,
> > > > + .owner = THIS_MODULE,
> > > > +};
> > > > +
> > > > +static int imx8_pcie_phy_probe(struct platform_device *pdev) {
> > > > + struct phy_provider *phy_provider;
> > > > + struct device *dev = &pdev->dev;
> > > > + struct device_node *np = dev->of_node;
> > > > + struct imx8_pcie_phy *imx8_phy;
> > > > + struct resource *res;
> > > > +
> > > > + imx8_phy = devm_kzalloc(dev, sizeof(*imx8_phy), GFP_KERNEL);
> > > > + if (!imx8_phy)
> > > > + return -ENOMEM;
> > > > +
> > > > + /* get PHY refclk pad mode */
> > > > + of_property_read_u32(np, "fsl,refclk-pad-mode",
> > > > + &imx8_phy->refclk_pad_mode);
> > > > +
> > > > + imx8_phy->clk = devm_clk_get(dev, "phy");
> > > > + if (IS_ERR(imx8_phy->clk)) {
> > > > + dev_err(dev, "failed to get imx pcie phy clock\n");
> > > > + return PTR_ERR(imx8_phy->clk);
> > > > + }
> > > > +
> > > > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > > > + imx8_phy->base = devm_ioremap_resource(dev, res);
> > > > + if (IS_ERR(imx8_phy->base))
> > > > + return PTR_ERR(imx8_phy->base);
> > > > +
> > > > + imx8_phy->phy = devm_phy_create(dev, NULL,
> &imx8_pcie_phy_ops);
> > > > + if (IS_ERR(imx8_phy->phy))
> > > > + return PTR_ERR(imx8_phy->phy);
> > > > +
> > > > + phy_set_drvdata(imx8_phy->phy, imx8_phy);
> > > > +
> > > > + phy_provider = devm_of_phy_provider_register(dev,
> > > > +of_phy_simple_xlate);
> > > > +
> > > > + return PTR_ERR_OR_ZERO(phy_provider); }
> > > > +
> > > > +static const struct of_device_id imx8_pcie_phy_of_match[] = {
> > > > + {.compatible = "fsl,imx8mm-pcie-phy",},
> > > > + { },
> > > > +};
> > > > +MODULE_DEVICE_TABLE(of, imx8_pcie_phy_of_match);
> > > > +
> > > > +static struct platform_driver imx8_pcie_phy_driver = {
> > > > + .probe = imx8_pcie_phy_probe,
> > > > + .driver = {
> > > > + .name = "imx8-pcie-phy",
> > > > + .of_match_table = imx8_pcie_phy_of_match,
> > > > + }
> > > > +};
> > > > +module_platform_driver(imx8_pcie_phy_driver);
> > > > +
> > > > +MODULE_DESCRIPTION("FSL IMX8 PCIE PHY driver");
> > > > +MODULE_LICENSE("GPL");
> > >
> >
>

\
 
 \ /
  Last update: 2021-10-11 09:49    [W:0.096 / U:0.036 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site