lkml.org 
[lkml]   [2021]   [Jan]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[RFC 2/2] clk: vc5: Add support for optional load capacitance
Date
There are two registers which can set the load capacitance for
XTAL1 and XTAL2. These are optional registers when using an
external crystal. Parse the device tree and set the
corresponding registers accordingly.

Signed-off-by: Adam Ford <aford173@gmail.com>
---
drivers/clk/clk-versaclock5.c | 64 +++++++++++++++++++++++++++++++++++
1 file changed, 64 insertions(+)

diff --git a/drivers/clk/clk-versaclock5.c b/drivers/clk/clk-versaclock5.c
index 43db67337bc0..445abc3731fb 100644
--- a/drivers/clk/clk-versaclock5.c
+++ b/drivers/clk/clk-versaclock5.c
@@ -759,6 +759,63 @@ static int vc5_update_power(struct device_node *np_output,
return 0;
}

+static int vc5_map_cap_value(u32 femtofarads)
+{
+ int mapped_value;
+
+ /* The datasheet explicitly states 9000 - 25000 */
+ if ((femtofarads < 9000) || (femtofarads > 25000))
+ return -EINVAL;
+
+ /* The lowest target we can hit is 9430, so exit if it's less */
+ if (femtofarads < 9430)
+ return 0;
+
+ /*
+ * According to VersaClock 6E Programming Guide, there are 6
+ * bits which translate to 64 entries in XTAL registers 12 and
+ * 13. Because bits 0 and 1 increase the capacitance the
+ * same, some of the values can be repeated. Plugging this
+ * into a spreadsheet and generating a trendline, the output
+ * equation becomes x = (y-9098.29) / 216.44, where 'y' is
+ * the desired capacitance in femtofarads, and x is the value
+ * of XTAL[5:0].
+ * To help with rounding, do fixed point math
+ */
+ femtofarads *= 100;
+ mapped_value = (femtofarads - 909829) / 21644;
+
+ /*
+ * The datasheet states, the maximum capacitance is 25000,
+ * but the programmer guide shows a max value is 22832,
+ * so values higher values could overflow, so cap it.
+ */
+ mapped_value = max(mapped_value/100, 0x3f);
+
+ return mapped_value;
+}
+static int vc5_update_cap_load(struct device_node *node, struct vc5_driver_data *vc5)
+{
+ u32 value, mapped_value;
+
+ if (!of_property_read_u32(node, "idt,xtal1-load-femtofarads", &value)) {
+ mapped_value = vc5_map_cap_value(value);
+ if (mapped_value < 0)
+ return mapped_value;
+
+ regmap_write(vc5->regmap, VC5_XTAL_X1_LOAD_CAP, (mapped_value << 2));
+ }
+
+ if (!of_property_read_u32(node, "idt,xtal2-load-femtofarads", &value)) {
+ mapped_value = vc5_map_cap_value(value);
+ if (mapped_value < 0)
+ return mapped_value;
+ regmap_write(vc5->regmap, VC5_XTAL_X2_LOAD_CAP, (mapped_value << 2));
+ }
+
+ return 0;
+}
+
static int vc5_update_slew(struct device_node *np_output,
struct vc5_out_data *clk_out)
{
@@ -884,6 +941,13 @@ static int vc5_probe(struct i2c_client *client, const struct i2c_device_id *id)
return -EINVAL;
}

+ /* Configure Optional Loading Capacitance for external XTAL */
+ if (!(vc5->chip_info->flags & VC5_HAS_INTERNAL_XTAL)) {
+ ret = vc5_update_cap_load(client->dev.of_node, vc5);
+ if (ret)
+ goto err_clk_register;
+ }
+
init.name = kasprintf(GFP_KERNEL, "%pOFn.mux", client->dev.of_node);
init.ops = &vc5_mux_ops;
init.flags = 0;
--
2.25.1
\
 
 \ /
  Last update: 2021-01-06 18:42    [W:0.149 / U:0.144 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site