lkml.org 
[lkml]   [2021]   [Jan]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] irqchip/irq-pruss-intc: implement set_type() callback
Date
This implements the irqchip set_type() callback for the TI PRUSS
interrupt controller. This is needed for cases where an event needs
to be active low.

According to the technical reference manual, the polarity should always
be set to high, however in practice, the polarity needs to be set low
for the McASP Tx/Rx system event in conjunction with soft UART PRU
firmware for TI AM18XX SoCs, otherwise it doesn't work.

Signed-off-by: David Lechner <david@lechnology.com>
---
drivers/irqchip/irq-pruss-intc.c | 27 +++++++++++++++++++++++++++
1 file changed, 27 insertions(+)

diff --git a/drivers/irqchip/irq-pruss-intc.c b/drivers/irqchip/irq-pruss-intc.c
index 5409016e6ca0..f882af8a7ded 100644
--- a/drivers/irqchip/irq-pruss-intc.c
+++ b/drivers/irqchip/irq-pruss-intc.c
@@ -334,6 +334,32 @@ static void pruss_intc_irq_unmask(struct irq_data *data)
pruss_intc_write_reg(intc, PRU_INTC_EISR, hwirq);
}

+static int pruss_intc_irq_set_type(struct irq_data *data, unsigned int type)
+{
+ struct pruss_intc *intc = irq_data_get_irq_chip_data(data);
+ u32 reg, bit, val;
+
+ if (type & IRQ_TYPE_LEVEL_MASK) {
+ /* polarity register */
+ reg = PRU_INTC_SIPR(data->hwirq / 32);
+ bit = BIT(data->hwirq % 32);
+ val = pruss_intc_read_reg(intc, reg);
+
+ /*
+ * This check also ensures that IRQ_TYPE_DEFAULT will result
+ * in setting the level to high.
+ */
+ if (type & IRQ_TYPE_LEVEL_HIGH)
+ val |= bit;
+ else
+ val &= ~bit;
+
+ pruss_intc_write_reg(intc, reg, val);
+ }
+
+ return 0;
+}
+
static int pruss_intc_irq_reqres(struct irq_data *data)
{
if (!try_module_get(THIS_MODULE))
@@ -389,6 +415,7 @@ static struct irq_chip pruss_irqchip = {
.irq_ack = pruss_intc_irq_ack,
.irq_mask = pruss_intc_irq_mask,
.irq_unmask = pruss_intc_irq_unmask,
+ .irq_set_type = pruss_intc_irq_set_type,
.irq_request_resources = pruss_intc_irq_reqres,
.irq_release_resources = pruss_intc_irq_relres,
.irq_get_irqchip_state = pruss_intc_irq_get_irqchip_state,
--
2.25.1
\
 
 \ /
  Last update: 2021-01-04 19:39    [W:0.063 / U:0.216 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site