lkml.org 
[lkml]   [2021]   [Jan]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] net: mdiobus: Prevent spike on MDIO bus reset signal
On Tue, Jan 26, 2021 at 01:49:38PM +0000, Russell King - ARM Linux admin wrote:
> On Tue, Jan 26, 2021 at 02:14:40PM +0100, Andrew Lunn wrote:
> > On Tue, Jan 26, 2021 at 08:33:37AM +0100, Mike Looijmans wrote:
> > > The mdio_bus reset code first de-asserted the reset by allocating with
> > > GPIOD_OUT_LOW, then asserted and de-asserted again. In other words, if
> > > the reset signal defaulted to asserted, there'd be a short "spike"
> > > before the reset.
> > >
> > > Instead, directly assert the reset signal using GPIOD_OUT_HIGH, this
> > > removes the spike and also removes a line of code since the signal
> > > is already high.
> >
> > Hi Mike
> >
> > This however appears to remove the reset pulse, if the reset line was
> > already low to start with. Notice you left
> >
> > fsleep(bus->reset_delay_us);
> >
> > without any action before it? What are we now waiting for? Most data
> > sheets talk of a reset pulse. Take the reset line high, wait for some
> > time, take the reset low, wait for some time, and then start talking
> > to the PHY. I think with this patch, we have lost the guarantee of a
> > low to high transition.
> >
> > Is this spike, followed by a pulse actually causing you problems? If
> > so, i would actually suggest adding another delay, to stretch the
> > spike. We have no control over the initial state of the reset line, it
> > is how the bootloader left it, we have to handle both states.
>
> Andrew, I don't get what you're saying.
>
> Here is what happens depending on the pre-existing state of the
> reset signal:
>
> Reset (previously asserted): ~~~|_|~~~~|_______
> Reset (previously deasserted): _____|~~~~|_______
> ^ ^ ^
> A B C
>
> At point A, the low going transition is because the reset line is
> requested using GPIOD_OUT_LOW. If the line is successfully requested,
> the first thing we do is set it high _without_ any delay. This is
> point B. So, a glitch occurs between A and B.
>
> We then fsleep() and finally set the GPIO low at point C.
>
> Requesting the line using GPIOD_OUT_HIGH eliminates the A and B
> transitions. Instead we get:
>
> Reset (previously asserted) : ~~~~~~~~~~|______
> Reset (previously deasserted): ____|~~~~~|______
> ^ ^
> A C
>
> Where A and C are the points described above in the code. Point B
> has been eliminated.
>
> Therefore, to me the patch looks entirely reasonable and correct.

I wonder if there are any PHYs which actually need a pulse? Would it
be better to have:

Reset (previously asserted): ~~~|____|~~~~|_______
Reset (previously deasserted): ________|~~~~|_______
^ ^ ^ ^
A B C D

Point D is where we actually start talking to the PHY. C-D is
reset-post-delay-us, and defaults to 0, but can be set via DT. B-C is
reset-delay-us, and defaults to 10us, but can be set via DT.
Currently A-B is '0', so we get the glitch. But should we make A-B the
same as B-C, so we get a real pulse?

Andrew

\
 
 \ /
  Last update: 2021-01-28 01:02    [W:0.105 / U:0.444 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site