lkml.org 
[lkml]   [2021]   [Jan]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v1 8/9] regulator: keembay: Add regulator for Keem Bay SoC
Date
Keem Bay SD regulator driver module is added to encapsulate ARM
Secure Monitor Call Calling Convention (SMCCC) during set voltage
operations to control I/O Rail supplied voltage levels which communicate
with Trusted Firmware.

I/O Rail voltage need to be configure through AON_CFG1 Register by
setting specific bit in the AON_CFG1 Register. AON_CFG1 Register is
a secure register. Direct access to AON_CFG1 register bit will cause
firewall violation in secure system.

Modelling using standard regulator abstraction during voltage operation
make things easier for device driver to consume it.

Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
---
drivers/regulator/Kconfig | 10 ++
drivers/regulator/Makefile | 1 +
drivers/regulator/keembay-sd-regulator.c | 112 +++++++++++++++++++++++
3 files changed, 123 insertions(+)
create mode 100644 drivers/regulator/keembay-sd-regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 5abdd29fb9f3..72cfd0d14066 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -436,6 +436,16 @@ config REGULATOR_ISL6271A
help
This driver supports ISL6271A voltage regulator chip.

+config REGULATOR_KEEMBAY_SD
+ tristate "Intel Keem Bay SD Regulator"
+ depends on HAVE_ARM_SMCCC && (OF || COMPILE_TEST)
+ help
+ This driver provides support for the voltage regulators of the
+ Keem Bay SOC to encapsulate ARM Secure Monitor Call Calling Convention
+ to change the voltage rail output.
+ This is specific for Keem Bay hardware design only.
+ The module name will be called keembay-sd-regulator.
+
config REGULATOR_LM363X
tristate "TI LM363X voltage regulators"
depends on MFD_TI_LMU
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 680e539f6579..0d2392441b66 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -52,6 +52,7 @@ obj-$(CONFIG_REGULATOR_HI6421V530) += hi6421v530-regulator.o
obj-$(CONFIG_REGULATOR_HI655X) += hi655x-regulator.o
obj-$(CONFIG_REGULATOR_ISL6271A) += isl6271a-regulator.o
obj-$(CONFIG_REGULATOR_ISL9305) += isl9305.o
+obj-$(CONFIG_REGULATOR_KEEMBAY_SD) += keembay-sd-regulator.o
obj-$(CONFIG_REGULATOR_LM363X) += lm363x-regulator.o
obj-$(CONFIG_REGULATOR_LOCHNAGAR) += lochnagar-regulator.o
obj-$(CONFIG_REGULATOR_LP3971) += lp3971.o
diff --git a/drivers/regulator/keembay-sd-regulator.c b/drivers/regulator/keembay-sd-regulator.c
new file mode 100644
index 000000000000..7f90c08de283
--- /dev/null
+++ b/drivers/regulator/keembay-sd-regulator.c
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Intel Keem Bay SD Regulator
+ *
+ * Copyright (C) 2020, Intel Corporation
+ * Author: Muhammad Husaini Zulkifli <Muhammad.Husaini.Zulkifli@intel.com>
+ */
+
+#include <linux/err.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+#include <linux/firmware/intel/keembay.h>
+
+static int keembay_regulator_set_voltage(struct regulator_dev *dev,
+ int min_uV, int max_uV,
+ unsigned *selector)
+{
+ int tmp_volt;
+
+ if (min_uV == KEEMBAY_IOV_1_8V_uV && max_uV == KEEMBAY_IOV_1_8V_uV)
+ tmp_volt = KEEMBAY_SET_1V8_IO_RAIL;
+ else
+ tmp_volt = KEEMBAY_SET_3V3_IO_RAIL;
+
+ return keembay_set_io_rail_supplied_voltage(tmp_volt);
+}
+
+static int keembay_regulator_get_voltage(struct regulator_dev *dev)
+{
+ int ret;
+
+ ret = keembay_get_io_rail_supplied_voltage();
+
+ return ret ? KEEMBAY_IOV_1_8V_uV : KEEMBAY_IOV_3_3V_uV;
+}
+
+static const struct regulator_ops keembay_regulator_voltage_ops = {
+ .get_voltage = keembay_regulator_get_voltage,
+ .set_voltage = keembay_regulator_set_voltage,
+};
+
+static int keembay_regulator_probe(struct platform_device *pdev)
+{
+ struct regulator_desc *desc;
+ struct regulator_init_data *init_data;
+ struct regulator_config config = { };
+ struct regulator_dev *rdev;
+ struct device *dev = &pdev->dev;
+
+ desc = devm_kzalloc(dev, sizeof(*desc), GFP_KERNEL);
+ if (!desc)
+ return -ENOMEM;
+
+ init_data = of_get_regulator_init_data(dev, dev->of_node, desc);
+ if (!init_data)
+ return -EINVAL;
+
+ desc->name = dev_name(dev);
+ desc->type = REGULATOR_VOLTAGE;
+ desc->owner = THIS_MODULE;
+ desc->ops = &keembay_regulator_voltage_ops;
+
+ config.dev = dev;
+ config.init_data = init_data;
+ config.of_node = dev->of_node;
+
+ rdev = devm_regulator_register(dev, desc, &config);
+ if (IS_ERR(rdev))
+ return dev_err_probe(dev, PTR_ERR(rdev),
+ "Failed to register Keem Bay SD regulator.\n");
+
+ return 0;
+}
+
+static const struct of_device_id regulator_keembay_of_match[] = {
+ { .compatible = "regulator-keembay-sd" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, regulator_keembay_of_match);
+
+static struct platform_driver keembay_regulator_driver = {
+ .probe = keembay_regulator_probe,
+ .driver = {
+ .name = "keembay-sd-regulator",
+ .of_match_table = regulator_keembay_of_match,
+ },
+};
+
+static int __init keembay_regulator_init(void)
+{
+ return platform_driver_register(&keembay_regulator_driver);
+}
+
+/*
+ * Using subsys_initcall to ensure that Keem Bay regulator platform driver
+ * is initialized before device driver try to utilize it.
+ */
+subsys_initcall(keembay_regulator_init);
+
+static void __exit keembay_regulator_exit(void)
+{
+ platform_driver_unregister(&keembay_regulator_driver);
+}
+module_exit(keembay_regulator_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Intel Keem Bay SD Regulator");
+MODULE_AUTHOR("Muhammad Husaini Zulkifli <Muhammad.Husaini.Zulkifli@intel.com>");
--
2.17.1
\
 
 \ /
  Last update: 2021-01-14 16:30    [W:0.182 / U:0.364 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site