lkml.org 
[lkml]   [2021]   [Jan]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH] brcmfmac: add support for CQM RSSI notifications
From
Date
On 12-01-2021 12:13, 'Alvin Šipraga' via BRCM80211-DEV-LIST,PDL wrote:
> Add support for CQM RSSI measurement reporting and advertise the
> NL80211_EXT_FEATURE_CQM_RSSI_LIST feature. This enables a userspace
> supplicant such as iwd to be notified of changes in the RSSI for roaming
> and signal monitoring purposes.

Needs a bit of rework. See my comments below...

> Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
> ---
> .../broadcom/brcm80211/brcmfmac/cfg80211.c | 82 +++++++++++++++++++
> .../broadcom/brcm80211/brcmfmac/cfg80211.h | 6 ++
> .../broadcom/brcm80211/brcmfmac/fwil_types.h | 28 +++++++
> 3 files changed, 116 insertions(+)
>
> diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
> index 0ee421f30aa2..21b53bd27f7f 100644
> --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
> +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
> @@ -5196,6 +5196,41 @@ brcmf_cfg80211_mgmt_tx(struct wiphy *wiphy, struct wireless_dev *wdev,
> return err;
> }
>
> +static int brcmf_cfg80211_set_cqm_rssi_range_config(struct wiphy *wiphy,
> + struct net_device *ndev,
> + s32 rssi_low, s32 rssi_high)
> +{
> + struct brcmf_cfg80211_vif *vif;
> + struct brcmf_if *ifp;
> + int err = 0;
> +
> + brcmf_dbg(TRACE, "low=%d high=%d", rssi_low, rssi_high);
> +
> + ifp = netdev_priv(ndev);
> + vif = ifp->vif;
> +
> + if (rssi_low != vif->cqm_rssi_low || rssi_high != vif->cqm_rssi_high) {
> + struct brcmf_rssi_event_le config = {
> + .rate_limit_msec = cpu_to_le32(0),
> + .rssi_level_num = 2,
> + .rssi_levels = {
> + max_t(s32, rssi_low, S8_MIN),
> + min_t(s32, rssi_high, S8_MAX),

The type should be s8 iso s32.

> + },
> + };

What is the expectation here? The firmware behavior for the above is
that you will get an event when the rssi is lower or equal to the level
and the previous rssi event was lower or equal to a different level.
There is another event RSSI_LQM that would be a better fit although that
is not available in every firmware image ("rssi_mon" firmware feature).

Another option would be to add a level, ie.:

.rssi_levels = {
max_t(s8, rssi_low, S8_MIN),
min_t(s8, rssi_high, S8_MAX - 1),
S8_MAX
}

> + err = brcmf_fil_iovar_data_set(ifp, "rssi_event", &config,
> + sizeof(config));
> + if (err) {
> + err = -EINVAL;
> + } else {
> + vif->cqm_rssi_low = rssi_low;
> + vif->cqm_rssi_high = rssi_high;
> + }
> + }
> +
> + return err;
> +}
>
> static int
> brcmf_cfg80211_cancel_remain_on_channel(struct wiphy *wiphy,
> @@ -5502,6 +5537,7 @@ static struct cfg80211_ops brcmf_cfg80211_ops = {
> .update_mgmt_frame_registrations =
> brcmf_cfg80211_update_mgmt_frame_registrations,
> .mgmt_tx = brcmf_cfg80211_mgmt_tx,
> + .set_cqm_rssi_range_config = brcmf_cfg80211_set_cqm_rssi_range_config,
> .remain_on_channel = brcmf_p2p_remain_on_channel,
> .cancel_remain_on_channel = brcmf_cfg80211_cancel_remain_on_channel,
> .get_channel = brcmf_cfg80211_get_channel,
> @@ -6137,6 +6173,49 @@ brcmf_notify_mic_status(struct brcmf_if *ifp,
> return 0;
> }
>
> +static s32 brcmf_notify_rssi(struct brcmf_if *ifp,
> + const struct brcmf_event_msg *e, void *data)

align to the opening brace in the line above.

> +{
> + struct brcmf_cfg80211_vif *vif = ifp->vif;
> + struct brcmf_rssi_be *info = data;
> + s32 rssi, snr, noise;
> + s32 low, high, last;
> +
> + if (e->datalen < sizeof(*info)) {
> + brcmf_err("insufficient RSSI event data\n");
> + return 0;
> + }
> +
> + rssi = be32_to_cpu(info->rssi);
> + snr = be32_to_cpu(info->snr);
> + noise = be32_to_cpu(info->noise);

Bit surprised to see this is BE, but it appears to be correct.

> + low = vif->cqm_rssi_low;
> + high = vif->cqm_rssi_high;
> + last = vif->cqm_rssi_last;
> +
> + brcmf_dbg(TRACE, "rssi=%d snr=%d noise=%d low=%d high=%d last=%d\n",
> + rssi, snr, noise, low, high, last);
> +
> + if (rssi != last) {

Given the firmware behavior I don't think you need this check.

> + vif->cqm_rssi_last = rssi;
> +
> + if (rssi <= low || rssi == 0) {
> + brcmf_dbg(INFO, "LOW rssi=%d\n", rssi);
> + cfg80211_cqm_rssi_notify(ifp->ndev,
> + NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW,
> + rssi, GFP_KERNEL);
> + } else if (rssi > high) {
> + brcmf_dbg(INFO, "HIGH rssi=%d\n", rssi);
> + cfg80211_cqm_rssi_notify(ifp->ndev,
> + NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH,
> + rssi, GFP_KERNEL);
> + }
> + }
> +
> + return 0;
--
This electronic communication and the information and any files transmitted
with it, or attached to it, are confidential and are intended solely for
the use of the individual or entity to whom it is addressed and may contain
information that is confidential, legally privileged, protected by privacy
laws, or otherwise restricted from disclosure to anyone else. If you are
not the intended recipient or the person responsible for delivering the
e-mail to the intended recipient, you are hereby notified that any use,
copying, distributing, dissemination, forwarding, printing, or copying of
this e-mail is strictly prohibited. If you received this e-mail in error,
please return the e-mail to the sender, delete it from your computer, and
destroy any printed copy of it.
[unhandled content-type:application/pkcs7-signature]
\
 
 \ /
  Last update: 2021-01-14 14:44    [W:0.069 / U:0.616 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site