lkml.org 
[lkml]   [2020]   [Sep]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] hwmon: intel-m10-bmc-hwmon: add hwmon support for Intel MAX 10 BMC
From
Date
On 9/9/20 12:02 AM, Xu Yilun wrote:
> On Tue, Sep 08, 2020 at 07:13:54AM -0700, Guenter Roeck wrote:
>> On 9/7/20 11:22 PM, Xu Yilun wrote:
>>> This patch adds hwmon functionality for Intel MAX 10 BMC chip. This BMC
>>> chip connects to a set of sensor chips to monitor current, voltage,
>>> thermal and power of different components on board. The BMC firmware is
>>> responsible for sensor data sampling and recording in shared registers.
>>> Host driver reads the sensor data from these shared registers and
>>> exposes them to users as hwmon interfaces.
>>>
>>> Signed-off-by: Xu Yilun <yilun.xu@intel.com>
>>> Signed-off-by: Wu Hao <hao.wu@intel.com>
>>> Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
>>> Signed-off-by: Tom Rix <trix@redhat.com>
>>> ---
>>> drivers/hwmon/Kconfig | 11 +
>>> drivers/hwmon/Makefile | 1 +
>>> drivers/hwmon/intel-m10-bmc-hwmon.c | 516 ++++++++++++++++++++++++++++++++++++
>>
>> Documentation/hwmon/intel-m10-bmc-hwmon is missing
>
> I'll add the Doc, thanks for the remind.
>
>>
>>> 3 files changed, 528 insertions(+)
>>> create mode 100644 drivers/hwmon/intel-m10-bmc-hwmon.c
>>>
>>> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
>>> index 8dc28b2..53af15c 100644
>>> --- a/drivers/hwmon/Kconfig
>>> +++ b/drivers/hwmon/Kconfig
>>> @@ -2064,6 +2064,17 @@ config SENSORS_XGENE
>>> If you say yes here you get support for the temperature
>>> and power sensors for APM X-Gene SoC.
>>>
>>> +config SENSORS_INTEL_M10_BMC_HWMON
>>> + tristate "Intel MAX10 BMC Hardware Monitoring"
>>> + depends on MFD_INTEL_M10_BMC
>>> + help
>>> + This driver provides support for the hardware monitoring functionality
>>> + on Intel MAX10 BMC chip.
>>> +
>>> + This BMC Chip is used on Intel FPGA PCIe Acceleration Cards (PAC). Its
>>> + sensors monitor various telemetry data of different components on the
>>> + card, e.g. board temperature, FPGA core temperature/voltage/current.
>>> +
>>> if ACPI
>>>
>>> comment "ACPI drivers"
>>> diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
>>> index a8f4b35..ba5a25a 100644
>>> --- a/drivers/hwmon/Makefile
>>> +++ b/drivers/hwmon/Makefile
>>> @@ -90,6 +90,7 @@ obj-$(CONFIG_SENSORS_IIO_HWMON) += iio_hwmon.o
>>> obj-$(CONFIG_SENSORS_INA209) += ina209.o
>>> obj-$(CONFIG_SENSORS_INA2XX) += ina2xx.o
>>> obj-$(CONFIG_SENSORS_INA3221) += ina3221.o
>>> +obj-$(CONFIG_SENSORS_INTEL_M10_BMC_HWMON) += intel-m10-bmc-hwmon.o
>>> obj-$(CONFIG_SENSORS_IT87) += it87.o
>>> obj-$(CONFIG_SENSORS_JC42) += jc42.o
>>> obj-$(CONFIG_SENSORS_K8TEMP) += k8temp.o
>>> diff --git a/drivers/hwmon/intel-m10-bmc-hwmon.c b/drivers/hwmon/intel-m10-bmc-hwmon.c
>>> new file mode 100644
>>> index 0000000..43e55e7
>>> --- /dev/null
>>> +++ b/drivers/hwmon/intel-m10-bmc-hwmon.c
>>> @@ -0,0 +1,516 @@
>>> +// SPDX-License-Identifier: GPL-2.0
>>> +/*
>>> + * Intel MAX 10 BMC HWMON Driver
>>> + *
>>> + * Copyright (C) 2018-2020 Intel Corporation. All rights reserved.
>>> + *
>>> + */
>>> +#include <linux/device.h>
>>> +#include <linux/hwmon.h>
>>> +#include <linux/hwmon-sysfs.h>
>>
>> Unnecessary include file.
>
> Yes, I'll remove it.
>
>>
>>> +#include <linux/mfd/intel-m10-bmc.h>
>>> +#include <linux/module.h>
>>> +#include <linux/mod_devicetable.h>
>>> +#include <linux/platform_device.h>
>>> +
>>> +enum m10bmc_channel_type {
>>> + M10BMC_CHT_TEMP,
>>> + M10BMC_CHT_IN,
>>> + M10BMC_CHT_CURR,
>>> + M10BMC_CHT_POWER,
>>> + M10BMC_CHT_MAX,
>>> +};
>>> +
>>> +struct m10bmc_sdata {
>>> + unsigned int type;
>>> + unsigned int reg_input;
>>> + unsigned int reg_max;
>>> + unsigned int reg_crit;
>>> + unsigned int reg_hyst;
>>> + unsigned int reg_min;
>>> + unsigned int multiplier;
>>> + const char *label;
>>> +};
>>> +
>>> +static struct m10bmc_sdata n3000bmc_sensor_tbl[] = {
>>
>> Can be const
>
> Yes.
>
>>
>>> + { M10BMC_CHT_TEMP, 0x100, 0x104, 0x108, 0x10c, 0x0, 500,
>>> + "Board Temperature" },
>>> + { M10BMC_CHT_TEMP, 0x110, 0x114, 0x118, 0x0, 0x0, 500,
>>> + "FPGA Die Temperature" },
>>> + { M10BMC_CHT_TEMP, 0x11c, 0x120, 0x124, 0x0, 0x0, 500,
>>> + "QSFP0 Temperature" },
>>> + { M10BMC_CHT_IN, 0x128, 0x0, 0x0, 0x0, 0x0, 1,
>>> + "QSFP0 Supply Voltage" },
>>> + { M10BMC_CHT_TEMP, 0x12c, 0x130, 0x134, 0x0, 0x0, 500,
>>> + "QSFP1 Temperature" },
>>> + { M10BMC_CHT_IN, 0x138, 0x0, 0x0, 0x0, 0x0, 1,
>>> + "QSFP1 Supply Voltage" },
>>> + { M10BMC_CHT_IN, 0x13c, 0x0, 0x0, 0x0, 0x0, 1,
>>> + "FPGA Core Voltage" },
>>> + { M10BMC_CHT_CURR, 0x140, 0x0, 0x0, 0x0, 0x0, 1,
>>> + "FPGA Core Current" },
>>> + { M10BMC_CHT_IN, 0x144, 0x0, 0x0, 0x0, 0x0, 1,
>>> + "12V Backplane Voltage" },
>>> + { M10BMC_CHT_CURR, 0x148, 0x0, 0x0, 0x0, 0x0, 1,
>>> + "12V Backplane Current" },
>>> + { M10BMC_CHT_IN, 0x14c, 0x0, 0x0, 0x0, 0x0, 1,
>>> + "1.2V Voltage" },
>>> + {M10BMC_CHT_IN, 0x150, 0x0, 0x0, 0x0, 0x0, 1,
>>> + "12V AUX Voltage" },
>>> + { M10BMC_CHT_CURR, 0x154, 0x0, 0x0, 0x0, 0x0, 1,
>>> + "12V AUX Current" },
>>> + { M10BMC_CHT_IN, 0x158, 0x0, 0x0, 0x0, 0x0, 1,
>>> + "1.8V Voltage" },
>>> + { M10BMC_CHT_IN, 0x15c, 0x0, 0x0, 0x0, 0x0, 1,
>>> + "3.3V Voltage" },
>>> + { M10BMC_CHT_POWER, 0x160, 0x0, 0x0, 0x0, 0x0, 1000,
>>> + "Board Power" },
>>> + { M10BMC_CHT_TEMP, 0x168, 0x0, 0x0, 0x0, 0x0, 500,
>>> + "Retimer A Temperature" },
>>> + { M10BMC_CHT_TEMP, 0x16c, 0x0, 0x0, 0x0, 0x0, 500,
>>> + "Retimer A SerDes Temperature" },
>>> + { M10BMC_CHT_TEMP, 0x170, 0x0, 0x0, 0x0, 0x0, 500,
>>> + "Retimer B Temperature" },
>>> + { M10BMC_CHT_TEMP, 0x174, 0x0, 0x0, 0x0, 0x0, 500,
>>> + "Retimer B SerDes Temperature" },
>>> + { M10BMC_CHT_MAX } /* sentinel */
>>> +};
>>> +
>>> +struct m10bmc_ch_group {
>>> + int num_channels;
>>> + struct m10bmc_sdata **data_list;
>>> + u32 *config;
>>> + struct hwmon_channel_info info;
>>> +};
>>> +
>>> +struct m10bmc_hwmon {
>>> + struct device *dev;
>>> + struct m10bmc_ch_group chgs[M10BMC_CHT_MAX];
>>> + /* This is a NULL terminated array required by the HWMON interface */
>>> + const struct hwmon_channel_info *info[M10BMC_CHT_MAX + 1];
>>> + struct hwmon_chip_info chip;
>>> + char *hw_name;
>>> + struct intel_m10bmc *m10bmc;
>>> + struct m10bmc_sdata *data_tbl;
>>> +};
>>> +
>>> +static enum m10bmc_channel_type
>>> +htype_to_ctype(enum hwmon_sensor_types htype)
>>> +{
>>> + switch (htype) {
>>> + case hwmon_temp:
>>> + return M10BMC_CHT_TEMP;
>>> + case hwmon_in:
>>> + return M10BMC_CHT_IN;
>>> + case hwmon_curr:
>>> + return M10BMC_CHT_CURR;
>>> + case hwmon_power:
>>> + return M10BMC_CHT_POWER;
>>> + default:
>>> + return M10BMC_CHT_MAX;
>>> + }
>>> +}
>>> +
>>> +static enum hwmon_sensor_types
>>> +ctype_to_htype(enum m10bmc_channel_type ctype)
>>> +{
>>> + switch (ctype) {
>>> + case M10BMC_CHT_TEMP:
>>> + return hwmon_temp;
>>> + case M10BMC_CHT_IN:
>>> + return hwmon_in;
>>> + case M10BMC_CHT_CURR:
>>> + return hwmon_curr;
>>> + case M10BMC_CHT_POWER:
>>> + return hwmon_power;
>>> + default:
>>> + return hwmon_max;
>>> + }
>>> +}
>>> +
>>> +static umode_t
>>> +m10bmc_hwmon_is_visible(const void *data, enum hwmon_sensor_types type,
>>> + u32 attr, int channel)
>>> +{
>>> + return 0444;
>>
>> It is quite unusual that limit attributes are read-only, but I guess
>> that is your call.
>
> Yes, actually the real sensor configurations are done by the firmware on
> MAX 10 BMC. We are not ready to support the sensor setting interfaces between
> the host & BMC.
>
>>
>>> +}
>>> +
>>> +static struct m10bmc_sdata *
>>> +find_sensor_data(struct m10bmc_hwmon *hw, enum hwmon_sensor_types htype,
>>> + int channel)
>>> +{
>>> + enum m10bmc_channel_type ctype = htype_to_ctype(htype);
>>> + struct m10bmc_ch_group *ch_group;
>>> +
>>> + if (ctype >= M10BMC_CHT_MAX)
>>> + return ERR_PTR(-EOPNOTSUPP);
>>> +
>>> + ch_group = &hw->chgs[ctype];
>>> +
>>> + if (channel >= ch_group->num_channels)
>>> + return ERR_PTR(-EOPNOTSUPP);
>>> +
>>> + return ch_group->data_list[channel];
>>> +}
>>> +
>>> +static int do_sensor_read(struct m10bmc_hwmon *hw, struct m10bmc_sdata *data,
>>> + unsigned int regoff, long *val)
>>> +{
>>> + unsigned int regval;
>>> + int ret;
>>> +
>>> + ret = m10bmc_sys_read(hw->m10bmc, regoff, &regval);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + /*
>>> + * BMC Firmware will return 0xdeadbeef if the sensor value is invalid
>>> + * at that time. This usually happens on sensor channels which connect
>>> + * to external pluggable modules, e.g. QSFP temperature and voltage.
>>> + * When the QSFP is unplugged from cage, driver will get 0xdeadbeef
>>> + * from their registers.
>>> + */
>>> + if (regval == 0xdeadbeef)
>>> + return -EBUSY;
>>> +
>>> + *val = regval * data->multiplier;
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int m10bmc_hwmon_read(struct device *dev, enum hwmon_sensor_types type,
>>> + u32 attr, int channel, long *val)
>>> +{
>>> + struct m10bmc_hwmon *hw = dev_get_drvdata(dev);
>>> + unsigned int reg, reg_hyst = 0;
>>> + struct m10bmc_sdata *data;
>>> + long hyst, value;
>>> + int ret;
>>> +
>>> + data = find_sensor_data(hw, type, channel);
>>> + if (IS_ERR(data))
>>> + return PTR_ERR(data);
>>> +
>>> + switch (type) {
>>> + case hwmon_temp:
>>> + switch (attr) {
>>> + case hwmon_temp_input:
>>> + reg = data->reg_input;
>>> + break;
>>> + case hwmon_temp_max_hyst:
>>> + reg_hyst = data->reg_hyst;
>>> + fallthrough;
>>> + case hwmon_temp_max:
>>> + reg = data->reg_max;
>>> + break;
>>> + case hwmon_temp_crit_hyst:
>>> + reg_hyst = data->reg_hyst;
>>> + fallthrough;
>>> + case hwmon_temp_crit:
>>> + reg = data->reg_crit;
>>> + break;
>>> + default:
>>> + return -EOPNOTSUPP;
>>> + }
>>> + break;
>>> + case hwmon_in:
>>> + switch (attr) {
>>> + case hwmon_in_input:
>>> + reg = data->reg_input;
>>> + break;
>>> + case hwmon_in_max:
>>> + reg = data->reg_max;
>>> + break;
>>> + case hwmon_in_crit:
>>> + reg = data->reg_crit;
>>> + break;
>>> + case hwmon_in_min:
>>> + reg = data->reg_min;
>>> + break;
>>> + default:
>>> + return -EOPNOTSUPP;
>>> + }
>>> + break;
>>> + case hwmon_curr:
>>> + switch (attr) {
>>> + case hwmon_curr_input:
>>> + reg = data->reg_input;
>>> + break;
>>> + case hwmon_curr_max:
>>> + reg = data->reg_max;
>>> + break;
>>> + case hwmon_curr_crit:
>>> + reg = data->reg_crit;
>>> + break;
>>> + default:
>>> + return -EOPNOTSUPP;
>>> + }
>>> + break;
>>> + case hwmon_power:
>>> + switch (attr) {
>>> + case hwmon_power_input:
>>> + reg = data->reg_input;
>>> + break;
>>> + default:
>>> + return -EOPNOTSUPP;
>>> + }
>>> + break;
>>> + default:
>>> + return -EOPNOTSUPP;
>>> + }
>>> +
>>> + ret = do_sensor_read(hw, data, reg, &value);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + if (reg_hyst) {
>>> + ret = do_sensor_read(hw, data, reg_hyst, &hyst);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + value -= hyst;
>>> + }
>>> +
>>> + *val = value;
>>> +
>>> + return ret;
>>> +}
>>> +
>>> +static int m10bmc_hwmon_read_string(struct device *dev,
>>> + enum hwmon_sensor_types type,
>>> + u32 attr, int channel, const char **str)
>>> +{
>>> + struct m10bmc_hwmon *hw = dev_get_drvdata(dev);
>>> + struct m10bmc_sdata *data;
>>> +
>>> + data = find_sensor_data(hw, type, channel);
>>> + if (!data)
>>> + return -EOPNOTSUPP;
>>> +
>>> + *str = data->label;
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static const struct hwmon_ops m10bmc_hwmon_ops = {
>>> + .is_visible = m10bmc_hwmon_is_visible,
>>> + .read = m10bmc_hwmon_read,
>>> + .read_string = m10bmc_hwmon_read_string,
>>> +};
>>> +
>>> +static int m10bmc_malloc_channels(struct device *dev,
>>> + struct m10bmc_ch_group *chg, int num_ch)
>>> +{
>>> + chg->config = devm_kcalloc(dev, num_ch + 1,
>>> + sizeof(*chg->config), GFP_KERNEL);
>>> + if (!chg->config)
>>> + return -ENOMEM;
>>> +
>>> + chg->data_list = devm_kcalloc(dev, num_ch, sizeof(*chg->data_list),
>>> + GFP_KERNEL);
>>> + if (!chg->data_list)
>>> + return -ENOMEM;
>>> +
>>> + chg->info.config = chg->config;
>>> + chg->num_channels = num_ch;
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static void m10bmc_fill_temp_channel(struct m10bmc_hwmon *hwmon, int ch_idx,
>>> + struct m10bmc_sdata *data)
>>> +{
>>> + struct m10bmc_ch_group *chg = &hwmon->chgs[M10BMC_CHT_TEMP];
>>> +
>>> + if (data->reg_input)
>>> + chg->config[ch_idx] |= HWMON_T_INPUT;
>>> +
>>> + if (data->reg_max) {
>>> + chg->config[ch_idx] |= HWMON_T_MAX;
>>> + if (data->reg_hyst)
>>> + chg->config[ch_idx] |= HWMON_T_MAX_HYST;
>>> + }
>>> +
>>> + if (data->reg_crit) {
>>> + chg->config[ch_idx] |= HWMON_T_CRIT;
>>> + if (data->reg_hyst)
>>> + chg->config[ch_idx] |= HWMON_T_CRIT_HYST;
>>> + }
>>> +
>>> + if (data->label)
>>> + chg->config[ch_idx] |= HWMON_T_LABEL;
>>> +
>>> + chg->data_list[ch_idx] = data;
>>> +}
>>> +
>>> +static void m10bmc_fill_in_channel(struct m10bmc_hwmon *hwmon, int ch_idx,
>>> + struct m10bmc_sdata *data)
>>> +{
>>> + struct m10bmc_ch_group *chg = &hwmon->chgs[M10BMC_CHT_IN];
>>> +
>>> + if (data->reg_input)
>>> + chg->config[ch_idx] |= HWMON_I_INPUT;
>>> +
>>> + if (data->reg_max)
>>> + chg->config[ch_idx] |= HWMON_I_MAX;
>>> +
>>> + if (data->reg_crit)
>>> + chg->config[ch_idx] |= HWMON_I_CRIT;
>>> +
>>> + if (data->reg_min)
>>> + chg->config[ch_idx] |= HWMON_I_MIN;
>>> +
>>> + if (data->label)
>>> + chg->config[ch_idx] |= HWMON_I_LABEL;
>>> +
>>> + chg->data_list[ch_idx] = data;
>>> +}
>>> +
>>> +static void m10bmc_fill_curr_channel(struct m10bmc_hwmon *hwmon, int ch_idx,
>>> + struct m10bmc_sdata *data)
>>> +{
>>> + struct m10bmc_ch_group *chg = &hwmon->chgs[M10BMC_CHT_CURR];
>>> +
>>> + if (data->reg_input)
>>> + chg->config[ch_idx] |= HWMON_C_INPUT;
>>> +
>>> + if (data->reg_max)
>>> + chg->config[ch_idx] |= HWMON_C_MAX;
>>> +
>>> + if (data->reg_crit)
>>> + chg->config[ch_idx] |= HWMON_C_CRIT;
>>> +
>>> + if (data->label)
>>> + chg->config[ch_idx] |= HWMON_C_LABEL;
>>> +
>>> + chg->data_list[ch_idx] = data;
>>> +}
>>> +
>>> +static void m10bmc_fill_power_channel(struct m10bmc_hwmon *hwmon, int ch_idx,
>>> + struct m10bmc_sdata *data)
>>> +{
>>> + struct m10bmc_ch_group *chg = &hwmon->chgs[M10BMC_CHT_POWER];
>>> +
>>> + if (data->reg_input)
>>> + chg->config[ch_idx] |= HWMON_P_INPUT;
>>> +
>>> + if (data->label)
>>> + chg->config[ch_idx] |= HWMON_P_LABEL;
>>> +
>>> + chg->data_list[ch_idx] = data;
>>> +}
>>
>> A substantial amount of code in this driver busies itself to convert
>> n3000bmc_sensor_tbl[] into the hwmon_channel_info data. What is the point
>> of doing that instead of providing struct hwmon_channel_info statically ?
>> One could write a little helper program to convert one into the other,
>> and avoid all this unnecessary code.
>>
>
> There are quite a lot of sensor data in the BMC, which are listed in the
> SPEC by the register address. And I have to classify them into type
> groups in order to use the static hwmon_channel_info. I also need to
> keep the alignment of the private sensor data table and
> hwmon_channel_info, like if limit attributes are available.
>

You could split n3000bmc_sensor_tbl[] into one table per sensor type,
and use a 1:1 index mapping. enum m10bmc_channel_type is unnecessary
anyway, you could have used hwmon types directly. And with one table
per type you would not even need that.

> And there is another board d5005 yet to be supported, with a different
> sensor set.
>
> So I think it may be easier we just fill one table according to SPEC, and
> dynamically creates the hwmon_channel_info.
>

I disagree. After splitting the table into one table per sensor type,
the rest of the implementation becomes effectively trivial. The dynamic
implementation is much more complex than it had to be and adds a lot
of code which is difficult to understand and maintain.

> Of course a helper program could generate the tables instead of the
> manual work.
>
Exactly. Though I really have to say that doint it manually, again
after splitting the table, becomes quite straightforward.

> I could change to static hwmon_channel_info according to your comments.
>
Please do.

Thanks,
Guenter

> Thanks,
> Yilun.
>
>>> +
>>> +static int m10bmc_hwmon_init(struct device *dev, struct intel_m10bmc *m10bmc,
>>> + const char *dev_name,
>>> + struct m10bmc_sdata *data_tbl)
>>> +{
>>> + int num_ch[M10BMC_CHT_MAX] = { 0 }, ret, i, j;
>>> + struct m10bmc_sdata *data = data_tbl;
>>> + struct device *hwmon_dev;
>>> + struct m10bmc_hwmon *hw;
>>> +
>>> + hw = devm_kzalloc(dev, sizeof(*hw), GFP_KERNEL);
>>> + if (!hw)
>>> + return -ENOMEM;
>>> +
>>> + hw->dev = dev;
>>> + hw->m10bmc = m10bmc;
>>> + hw->data_tbl = data_tbl;
>>> +
>>> + while (data->type != M10BMC_CHT_MAX) {
>>> + if (data->type > M10BMC_CHT_MAX)
>>> + return -EINVAL;
>>> +
>>> + ++num_ch[data->type];
>>> + ++data;
>>> + }
>>> +
>>> + for (i = 0; i < M10BMC_CHT_MAX; i++) {
>>> + if (!num_ch[i])
>>> + continue;
>>> +
>>> + ret = m10bmc_malloc_channels(dev, &hw->chgs[i],
>>> + num_ch[i]);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + hw->chgs[i].info.type = ctype_to_htype(i);
>>> + }
>>> +
>>> + data = data_tbl;
>>> + memset(&num_ch, 0, sizeof(num_ch));
>>> + while (data->type != M10BMC_CHT_MAX) {
>>> + switch (data->type) {
>>> + case M10BMC_CHT_TEMP:
>>> + m10bmc_fill_temp_channel(hw, num_ch[data->type],
>>> + data);
>>> + break;
>>> + case M10BMC_CHT_IN:
>>> + m10bmc_fill_in_channel(hw, num_ch[data->type],
>>> + data);
>>> + break;
>>> + case M10BMC_CHT_CURR:
>>> + m10bmc_fill_curr_channel(hw, num_ch[data->type],
>>> + data);
>>> + break;
>>> + case M10BMC_CHT_POWER:
>>> + m10bmc_fill_power_channel(hw, num_ch[data->type],
>>> + data);
>>> + break;
>>> + }
>>> +
>>> + ++num_ch[data->type];
>>> + ++data;
>>> + }
>>> +
>>> + for (i = 0, j = 0; i < M10BMC_CHT_MAX; i++) {
>>> + if (num_ch[i])
>>> + hw->info[j++] = &hw->chgs[i].info;
>>> + }
>>> +
>>> + hw->chip.info = hw->info;
>>> + hw->chip.ops = &m10bmc_hwmon_ops;
>>> +
>>> + hw->hw_name = devm_kstrdup(dev, dev_name, GFP_KERNEL);
>>> + if (!hw->hw_name)
>>> + return -ENOMEM;
>>> +
>>> + for (i = 0; hw->hw_name[i]; i++)
>>> + if (hwmon_is_bad_char(hw->hw_name[i]))
>>> + hw->hw_name[i] = '_';
>>> +
>>> + hwmon_dev = devm_hwmon_device_register_with_info(dev, hw->hw_name,
>>> + hw, &hw->chip, NULL);
>>> + return PTR_ERR_OR_ZERO(hwmon_dev);
>>> +}
>>> +
>>> +static int m10bmc_hwmon_probe(struct platform_device *pdev)
>>> +{
>>> + const struct platform_device_id *id = platform_get_device_id(pdev);
>>> + struct intel_m10bmc *m10bmc = dev_get_drvdata(pdev->dev.parent);
>>> +
>>> + return m10bmc_hwmon_init(&pdev->dev, m10bmc, id->name,
>>> + (struct m10bmc_sdata *)id->driver_data);
>>> +}
>>> +
>>> +static const struct platform_device_id intel_m10bmc_hwmon_ids[] = {
>>> + {
>>> + .name = "n3000bmc-hwmon",
>>> + .driver_data = (unsigned long)&n3000bmc_sensor_tbl,
>>> + },
>>> + { }
>>> +};
>>> +
>>> +static struct platform_driver intel_m10bmc_hwmon_driver = {
>>> + .probe = m10bmc_hwmon_probe,
>>> + .driver = {
>>> + .name = "intel-m10-bmc-hwmon",
>>> + },
>>> + .id_table = intel_m10bmc_hwmon_ids,
>>> +};
>>> +module_platform_driver(intel_m10bmc_hwmon_driver);
>>> +
>>> +MODULE_DEVICE_TABLE(platform, intel_m10bmc_hwmon_ids);
>>> +MODULE_AUTHOR("Intel Corporation");
>>> +MODULE_DESCRIPTION("Intel MAX 10 BMC hardware monitor");
>>> +MODULE_LICENSE("GPL");
>>>

\
 
 \ /
  Last update: 2020-09-09 18:46    [W:0.064 / U:0.284 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site