lkml.org 
[lkml]   [2020]   [Sep]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 3/4] remoteproc: k3-r5: Initialize TCM memories for ECC
Date
The R5F processors on K3 SoCs all have two TCMs (ATCM and BTCM) that
support 32-bit ECC. The TCMs are typically loaded with some boot-up
code to initialize the R5 MPUs to further execute code out of DDR.
The ECC for the TCMs is enabled by default on K3 SoCs due to internal
default tie-off values, but the TCM memories are not initialized on
device power up. Any read access without the corresponding TCM memory
location initialized will generate an ECC error, and any such access
from a A72 or A53 core will trigger a SError.

So, zero initialize both the TCM memories before loading any firmware
onto a R5F in remoteproc mode. Any R5F booted from U-Boot/SPL would
require a similar initialization in the bootloader. Note that both
the TCMs are initialized unconditionally as the TCM enable config bits
only manage the access and visibility from R5.

Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
---
v4: No changes
v3: https://patchwork.kernel.org/patch/11679335/
- No code changes, picked up tags
v2: https://patchwork.kernel.org/patch/11632989/
v1: https://patchwork.kernel.org/patch/11456371/

drivers/remoteproc/ti_k3_r5_remoteproc.c | 17 +++++++++++++++--
1 file changed, 15 insertions(+), 2 deletions(-)

diff --git a/drivers/remoteproc/ti_k3_r5_remoteproc.c b/drivers/remoteproc/ti_k3_r5_remoteproc.c
index 15e52ea67bbe..a6b395ab47b6 100644
--- a/drivers/remoteproc/ti_k3_r5_remoteproc.c
+++ b/drivers/remoteproc/ti_k3_r5_remoteproc.c
@@ -362,11 +362,24 @@ static int k3_r5_rproc_prepare(struct rproc *rproc)

ret = (cluster->mode == CLUSTER_MODE_LOCKSTEP) ?
k3_r5_lockstep_release(cluster) : k3_r5_split_release(core);
- if (ret)
+ if (ret) {
dev_err(dev, "unable to enable cores for TCM loading, ret = %d\n",
ret);
+ return ret;
+ }

- return ret;
+ /*
+ * Zero out both TCMs unconditionally (access from v8 Arm core is not
+ * affected by ATCM & BTCM enable configuration values) so that ECC
+ * can be effective on all TCM addresses.
+ */
+ dev_dbg(dev, "zeroing out ATCM memory\n");
+ memset(core->mem[0].cpu_addr, 0x00, core->mem[0].size);
+
+ dev_dbg(dev, "zeroing out BTCM memory\n");
+ memset(core->mem[1].cpu_addr, 0x00, core->mem[1].size);
+
+ return 0;
}

/*
--
2.28.0
\
 
 \ /
  Last update: 2020-09-08 19:49    [W:0.063 / U:2.412 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site