lkml.org 
[lkml]   [2020]   [Sep]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v11 3/5] arm64: kdump: reimplement crashkernel=X
From
Date


On 2020/9/4 11:10, Dave Young wrote:
> On 09/04/20 at 11:04am, Dave Young wrote:
>> On 09/03/20 at 07:26pm, chenzhou wrote:
>>> Hi Catalin,
>>>
>>>
>>> On 2020/9/3 1:09, Catalin Marinas wrote:
>>>> On Sat, Aug 01, 2020 at 09:08:54PM +0800, Chen Zhou wrote:
>>>>> There are following issues in arm64 kdump:
>>>>> 1. We use crashkernel=X to reserve crashkernel below 4G, which
>>>>> will fail when there is no enough low memory.
>>>>> 2. If reserving crashkernel above 4G, in this case, crash dump
>>>>> kernel will boot failure because there is no low memory available
>>>>> for allocation.
>>>>> 3. Since commit 1a8e1cef7603 ("arm64: use both ZONE_DMA and ZONE_DMA32"),
>>>>> if the memory reserved for crash dump kernel falled in ZONE_DMA32,
>>>>> the devices in crash dump kernel need to use ZONE_DMA will alloc
>>>>> fail.
>>>>>
>>>>> To solve these issues, change the behavior of crashkernel=X.
>>>>> crashkernel=X tries low allocation in ZONE_DMA, and fall back to
>>>>> high allocation if it fails.
>>>>>
>>>>> If requized size X is too large and leads to very little free memory
>>>>> in ZONE_DMA after low allocation, the system may not work normally.
>>>>> So add a threshold and go for high allocation directly if the required
>>>>> size is too large. The value of threshold is set as the half of
>>>>> the low memory.
>>>>>
>>>>> If crash_base is outside ZONE_DMA, try to allocate at least 256M in
>>>>> ZONE_DMA automatically. "crashkernel=Y,low" can be used to allocate
>>>>> specified size low memory.
>>>> Except for the threshold to keep zone ZONE_DMA memory,
>>>> reserve_crashkernel() looks very close to the x86 version. Shall we try
>>>> to make this generic as well? In the first instance, you could avoid the
>>>> threshold check if it takes an explicit ",high" option.
>>> Ok, i will try to do this.
>>>
>>> I look into the function reserve_crashkernel() of x86 and found the start address is
>>> CRASH_ALIGN in function memblock_find_in_range(), which is different with arm64.
>>>
>>> I don't figure out why is CRASH_ALIGN in x86, is there any specific reason?
>> Hmm, took another look at the option CONFIG_PHYSICAL_ALIGN
>> config PHYSICAL_ALIGN
>> hex "Alignment value to which kernel should be aligned"
>> default "0x200000"
>> range 0x2000 0x1000000 if X86_32
>> range 0x200000 0x1000000 if X86_64
>>
>> According to above, I think the 16M should come from the largest value
>> But the default value is 2M, with smaller value reservation can have
>> more chance to succeed.
>>
>> It seems we still need arch specific CRASH_ALIGN, but the initial
>> version you added the #ifdef for different arches, can you move the
>> macro to arch specific headers?
> And just keep the x86 align value as is, I can try to change the x86
> value later to CONFIG_PHYSICAL_ALIGN, in this way this series can be
> cleaner.
Ok. I have no question about the value of macro CRASH_ALIGN,
instead the lower bound of memblock_find_in_range().

For x86, in reserve_crashkernel(),restrict the lower bound of the range to CRASH_ALIGN,
...
crash_base = memblock_find_in_range(CRASH_ALIGN,
CRASH_ADDR_LOW_MAX,
crash_size, CRASH_ALIGN);
...

in reserve_crashkernel_low(),with no this restriction.
...
low_base = memblock_find_in_range(0, 1ULL << 32, low_size, CRASH_ALIGN);
...

How about all making memblock_find_in_range() search from the start of memory?
If it is ok, i will do like this in the generic version.

Thanks,
Chen Zhou
>
>> Thanks
>> Dave
>
> .
>


\
 
 \ /
  Last update: 2020-09-04 06:05    [W:1.311 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site