lkml.org 
[lkml]   [2020]   [Sep]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH V2 6/7] PCI: qcom: Add ipq8074 PCIe controller support
On Wed, Jul 29, 2020 at 09:00:06PM +0530, Sivaprakash Murugesan wrote:
> Add support for PCIe Gen3 port found in ipq8074 devices.
>
> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> ---
> drivers/pci/controller/dwc/pcie-qcom.c | 177 ++++++++++++++++++++++++++++++++-
> 1 file changed, 176 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index e1b5651..3bddfcff 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -40,6 +40,14 @@
> #define L23_CLK_RMV_DIS BIT(2)
> #define L1_CLK_RMV_DIS BIT(1)
>
> +#define PCIE_ATU_CR1_OUTBOUND_6_GEN3 0xC00
> +#define PCIE_ATU_CR2_OUTBOUND_6_GEN3 0xC04
> +#define PCIE_ATU_LIMIT_OUTBOUND_6_GEN3 0xC10
> +#define PCIE_ATU_CR1_OUTBOUND_7_GEN3 0xE00
> +#define PCIE_ATU_CR2_OUTBOUND_7_GEN3 0xE04
> +#define PCIE_ATU_LOWER_BASE_OUTBOUND_7_GEN3 0xE08
> +#define PCIE_ATU_LIMIT_OUTBOUND_7_GEN3 0xE10

Looks like standard DWC ATU registers.

> +
> #define PCIE20_PARF_PHY_CTRL 0x40
> #define PHY_CTRL_PHY_TX0_TERM_OFFSET_MASK GENMASK(20, 16)
> #define PHY_CTRL_PHY_TX0_TERM_OFFSET(x) ((x) << 16)
> @@ -58,6 +66,13 @@
> #define PCIE20_PARF_BDF_TRANSLATE_CFG 0x24C
> #define PCIE20_PARF_DEVICE_TYPE 0x1000
>
> +#define AHB_CLK_EN BIT(0)
> +#define MSTR_AXI_CLK_EN BIT(1)
> +#define BYPASS BIT(4)
> +
> +#define PCIE20_PARF_BDF_TO_SID_TABLE 0x2000
> +#define BDF_TO_SID_TABLE_SIZE 0x100
> +
> #define PCIE20_ELBI_SYS_CTRL 0x04
> #define PCIE20_ELBI_SYS_CTRL_LT_ENABLE BIT(0)
>
> @@ -68,11 +83,13 @@
> #define CFG_BRIDGE_SB_INIT BIT(0)
>
> #define PCIE20_CAP 0x70
> -#define PCIE20_DEVICE_CONTROL2_STATUS2 (PCIE20_CAP + PCI_EXP_DEVCTL2)
> #define PCIE20_CAP_LINK_CAPABILITIES (PCIE20_CAP + PCI_EXP_LNKCAP)
> #define PCIE20_CAP_LINK_1 (PCIE20_CAP + 0x14)
> #define PCIE_CAP_LINK1_VAL 0x2FD7F
>
> +#define PCIE20_DEVICE_CONTROL2_STATUS2 (PCIE20_CAP + PCI_EXP_DEVCTL2)
> +#define PCIE_CAP_CPL_TIMEOUT_DISABLE 0x10

Gone now in Lorenzo's pci/dwc branch.

> +
> #define PCIE20_PARF_Q2A_FLUSH 0x1AC
>
> #define PCIE20_MISC_CONTROL_1_REG 0x8BC
> @@ -96,9 +113,15 @@
> #define SLV_ADDR_SPACE_SZ 0x10000000
>
> #define PCIE20_LNK_CONTROL2_LINK_STATUS2 0xa0
> +#define PCIE_CAP_CURR_DEEMPHASIS BIT(16)
> +#define SPEED_GEN3 0x3
>
> #define DEVICE_TYPE_RC 0x4
>
> +#define PCIE30_GEN3_RELATED_OFF 0x890
> +#define RXEQ_RGRDLESS_RXTS BIT(13)
> +#define GEN3_ZRXDC_NONCOMPL BIT(0)
> +
> #define QCOM_PCIE_2_1_0_MAX_SUPPLY 3
> #define QCOM_PCIE_2_1_0_MAX_CLOCKS 5
> struct qcom_pcie_resources_2_1_0 {
> @@ -165,6 +188,11 @@ struct qcom_pcie_resources_2_7_0 {
> struct clk *pipe_clk;
> };
>
> +struct qcom_pcie_resources_2_9_0 {
> + struct clk_bulk_data clks[7];
> + struct reset_control *rst[8];
> +};
> +
> union qcom_pcie_resources {
> struct qcom_pcie_resources_1_0_0 v1_0_0;
> struct qcom_pcie_resources_2_1_0 v2_1_0;
> @@ -172,6 +200,7 @@ union qcom_pcie_resources {
> struct qcom_pcie_resources_2_3_3 v2_3_3;
> struct qcom_pcie_resources_2_4_0 v2_4_0;
> struct qcom_pcie_resources_2_7_0 v2_7_0;
> + struct qcom_pcie_resources_2_9_0 v2_9_0;
> };
>
> struct qcom_pcie;
> @@ -1250,6 +1279,134 @@ static void qcom_pcie_post_deinit_2_7_0(struct qcom_pcie *pcie)
> clk_disable_unprepare(res->pipe_clk);
> }
>
> +static int qcom_pcie_get_resources_2_9_0(struct qcom_pcie *pcie)
> +{
> + struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> + struct dw_pcie *pci = pcie->pci;
> + struct device *dev = pci->dev;
> + int ret, i;
> + const char *rst_names[] = { "pipe", "sleep", "sticky", "axi_m",
> + "axi_s", "ahb", "axi_m_sticky",
> + "axi_s_sticky" };
> +
> + res->clks[0].id = "iface";
> + res->clks[1].id = "axi_m";
> + res->clks[2].id = "axi_s";
> + res->clks[3].id = "ahb";
> + res->clks[4].id = "aux";
> + res->clks[5].id = "axi_bridge";
> + res->clks[6].id = "rchng";
> +
> + ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
> + if (ret < 0)
> + return ret;
> +
> + for (i = 0; i < ARRAY_SIZE(rst_names); i++) {
> + res->rst[i] = devm_reset_control_get(dev, rst_names[i]);
> + if (IS_ERR(res->rst[i]))
> + return PTR_ERR(res->rst[i]);
> + }
> +
> + return 0;
> +}
> +
> +static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
> +{
> + struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> + struct dw_pcie *pci = pcie->pci;
> + struct device *dev = pci->dev;
> + int i, ret;
> + u32 val;
> + u32 bus_master_en = PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER;
> +
> + for (i = 0; i < ARRAY_SIZE(res->rst); i++) {
> + ret = reset_control_assert(res->rst[i]);
> + if (ret) {
> + dev_err(dev, "reset #%d assert failed (%d)\n", i, ret);
> + return ret;
> + }
> + }
> +
> + usleep_range(2000, 2500);
> +
> + for (i = 0; i < ARRAY_SIZE(res->rst); i++) {
> + ret = reset_control_deassert(res->rst[i]);
> + if (ret) {
> + dev_err(dev, "reset #%d deassert failed (%d)\n", i,
> + ret);
> + return ret;
> + }
> + }
> +
> + /*
> + * Don't have a way to see if the reset has completed.
> + * Wait for some time.
> + */
> + usleep_range(2000, 2500);
> +
> + ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> + if (ret)
> + return ret;
> +
> + /* Parf config */
> + writel(SLV_ADDR_SPACE_SZ,
> + pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE);

relaxed variants should work here, right?

> +
> + val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
> + val &= ~BIT(0);

A define for bit 0 needed.

> + writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
> +
> + writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR);
> + writel(DEVICE_TYPE_RC, pcie->parf + PCIE20_PARF_DEVICE_TYPE);
> + writel(BYPASS | MSTR_AXI_CLK_EN | AHB_CLK_EN,
> + pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
> +
> + writel(RXEQ_RGRDLESS_RXTS | GEN3_ZRXDC_NONCOMPL,
> + pci->dbi_base + PCIE30_GEN3_RELATED_OFF);
> + writel(MST_WAKEUP_EN | SLV_WAKEUP_EN | MSTR_ACLK_CGC_DIS
> + | SLV_ACLK_CGC_DIS | CORE_CLK_CGC_DIS |
> + AUX_PWR_DET | L23_CLK_RMV_DIS | L1_CLK_RMV_DIS,
> + pcie->parf + PCIE20_PARF_SYS_CTRL);
> + writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH);
> +
> + /* DBI config */
> + writel(bus_master_en, pci->dbi_base + PCI_COMMAND);

The core does this.

> + writel(DBI_RO_WR_EN, pci->dbi_base + PCIE20_MISC_CONTROL_1_REG);
> + writel(PCIE_CAP_LINK1_VAL, pci->dbi_base + PCIE20_CAP_LINK_1);
> +
> + /* Configure PCIe link capabilities for ASPM */
> + val = readl(pci->dbi_base + PCIE20_CAP_LINK_CAPABILITIES);
> + val &= ~PCI_EXP_LNKCAP_ASPMS;
> + writel(val, pci->dbi_base + PCIE20_CAP_LINK_CAPABILITIES);
> +
> + writel(PCIE_CAP_CPL_TIMEOUT_DISABLE, pci->dbi_base +
> + PCIE20_DEVICE_CONTROL2_STATUS2);
> +
> + writel(PCIE_CAP_CURR_DEEMPHASIS | SPEED_GEN3,
> + pci->dbi_base + PCIE20_LNK_CONTROL2_LINK_STATUS2);
> +
> + for (i = 0 ; i < BDF_TO_SID_TABLE_SIZE ; i++)
> + writel(0x0, pcie->parf + PCIE20_PARF_BDF_TO_SID_TABLE + (4 * i));
> +
> + writel(0x4, pci->atu_base + PCIE_ATU_CR1_OUTBOUND_6_GEN3);
> + writel(0x90000000, pci->atu_base + PCIE_ATU_CR2_OUTBOUND_6_GEN3);
> + writel(0x00107FFFF, pci->atu_base + PCIE_ATU_LIMIT_OUTBOUND_6_GEN3);
> + writel(0x5, pci->atu_base + PCIE_ATU_CR1_OUTBOUND_7_GEN3);
> + writel(0x90000000, pci->atu_base + PCIE_ATU_CR2_OUTBOUND_7_GEN3);
> + writel(0x200000, pci->atu_base + PCIE_ATU_LOWER_BASE_OUTBOUND_7_GEN3);
> + writel(0x7FFFFF, pci->atu_base + PCIE_ATU_LIMIT_OUTBOUND_7_GEN3);

No, this should all come from 'ranges'.

> +
> + return 0;
> +}
> +
> +static void qcom_pcie_deinit_2_9_0(struct qcom_pcie *pcie)
> +{
> + struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> +
> + clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> +}
> +
> static int qcom_pcie_link_up(struct dw_pcie *pci)
> {
> u16 val = readw(pci->dbi_base + PCIE20_CAP + PCI_EXP_LNKSTA);
> @@ -1359,6 +1516,14 @@ static const struct qcom_pcie_ops ops_2_7_0 = {
> .post_deinit = qcom_pcie_post_deinit_2_7_0,
> };
>
> +/* Qcom IP rev.: 2.9.0 Synopsys IP rev.: 5.00a */
> +static const struct qcom_pcie_ops ops_2_9_0 = {
> + .get_resources = qcom_pcie_get_resources_2_9_0,
> + .init = qcom_pcie_init_2_9_0,
> + .deinit = qcom_pcie_deinit_2_9_0,
> + .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
> +};
> +
> static const struct dw_pcie_ops dw_pcie_ops = {
> .link_up = qcom_pcie_link_up,
> };
> @@ -1399,6 +1564,15 @@ static int qcom_pcie_probe(struct platform_device *pdev)
> goto err_pm_runtime_put;
> }
>
> + if (pcie->ops == &ops_2_9_0) {
> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "atu");

There's a patch in flight to do this in the DWC common code.

> + pci->atu_base = devm_pci_remap_cfg_resource(dev, res);
> + if (IS_ERR(pci->atu_base)) {
> + ret = PTR_ERR(pci->atu_base);
> + goto err_pm_runtime_put;
> + }
> + }
> +
> pcie->gen = of_pci_get_max_link_speed(pdev->dev.of_node);
> if (pcie->gen < 0)
> pcie->gen = 2;
> @@ -1476,6 +1650,7 @@ static const struct of_device_id qcom_pcie_match[] = {
> { .compatible = "qcom,pcie-ipq4019", .data = &ops_2_4_0 },
> { .compatible = "qcom,pcie-qcs404", .data = &ops_2_4_0 },
> { .compatible = "qcom,pcie-sdm845", .data = &ops_2_7_0 },
> + { .compatible = "qcom,pcie-ipq8074-gen3", .data = &ops_2_9_0 },

Is there a non gen3 PCIe host in ipq8074?

Rob

\
 
 \ /
  Last update: 2020-09-30 20:14    [W:0.084 / U:1.904 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site