lkml.org 
[lkml]   [2020]   [Sep]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 4/4] media: i2c: imx258: get clock from device properties and enable it via runtime PM
On Tue, Sep 29, 2020 at 12:17:04PM +0300, Sakari Ailus wrote:
> Hi Krzysztof,
>
> On Wed, Sep 23, 2020 at 05:21:29PM +0200, Krzysztof Kozlowski wrote:
> > The IMX258 sensor driver checked in device properties for a
> > clock-frequency property which actually does not mean that the clock is
> > really running such frequency or is it even enabled.
> >
> > Get the provided clock and check it frequency. If none is provided,
> > fall back to old property.
> >
> > Enable the clock when accessing the IMX258 registers and when streaming
> > starts with runtime PM.
> >
> > Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
> >
> > ---
> >
> > Changes since v3:
> > 1. None
> >
> > Changes since v2:
> > 1. Do not try to set drvdata, wrap lines.
> > 2. Use dev_dbg.
> >
> > Changes since v1:
> > 1. Use runtime PM for clock toggling
> > ---
> > drivers/media/i2c/imx258.c | 71 +++++++++++++++++++++++++++++++++-----
> > 1 file changed, 62 insertions(+), 9 deletions(-)
> >
> > diff --git a/drivers/media/i2c/imx258.c b/drivers/media/i2c/imx258.c
> > index ae183b0dbba9..7bedbfe5c4d6 100644
> > --- a/drivers/media/i2c/imx258.c
> > +++ b/drivers/media/i2c/imx258.c
> > @@ -2,6 +2,7 @@
> > // Copyright (C) 2018 Intel Corporation
> >
> > #include <linux/acpi.h>
> > +#include <linux/clk.h>
> > #include <linux/delay.h>
> > #include <linux/i2c.h>
> > #include <linux/module.h>
> > @@ -68,6 +69,9 @@
> > #define REG_CONFIG_MIRROR_FLIP 0x03
> > #define REG_CONFIG_FLIP_TEST_PATTERN 0x02
> >
> > +/* Input clock frequency in Hz */
> > +#define IMX258_INPUT_CLOCK_FREQ 19200000
> > +
> > struct imx258_reg {
> > u16 address;
> > u8 val;
> > @@ -610,6 +614,8 @@ struct imx258 {
> >
> > /* Streaming on/off */
> > bool streaming;
> > +
> > + struct clk *clk;
> > };
> >
> > static inline struct imx258 *to_imx258(struct v4l2_subdev *_sd)
> > @@ -972,6 +978,29 @@ static int imx258_stop_streaming(struct imx258 *imx258)
> > return 0;
> > }
> >
> > +static int imx258_power_on(struct device *dev)
> > +{
> > + struct v4l2_subdev *sd = dev_get_drvdata(dev);
> > + struct imx258 *imx258 = to_imx258(sd);
> > + int ret;
> > +
> > + ret = clk_prepare_enable(imx258->clk);
> > + if (ret)
> > + dev_err(dev, "failed to enable clock\n");
> > +
> > + return ret;
> > +}
> > +
> > +static int imx258_power_off(struct device *dev)
> > +{
> > + struct v4l2_subdev *sd = dev_get_drvdata(dev);
> > + struct imx258 *imx258 = to_imx258(sd);
> > +
> > + clk_disable_unprepare(imx258->clk);
> > +
> > + return 0;
> > +}
> > +
> > static int imx258_set_stream(struct v4l2_subdev *sd, int enable)
> > {
> > struct imx258 *imx258 = to_imx258(sd);
> > @@ -1199,9 +1228,28 @@ static int imx258_probe(struct i2c_client *client)
> > int ret;
> > u32 val = 0;
> >
> > - device_property_read_u32(&client->dev, "clock-frequency", &val);
> > - if (val != 19200000)
> > - return -EINVAL;
> > + imx258 = devm_kzalloc(&client->dev, sizeof(*imx258), GFP_KERNEL);
> > + if (!imx258)
> > + return -ENOMEM;
> > +
> > + imx258->clk = devm_clk_get_optional(&client->dev, NULL);
> > + if (!imx258->clk) {
> > + dev_dbg(&client->dev,
> > + "no clock provided, using clock-frequency property\n");
> > +
> > + device_property_read_u32(&client->dev, "clock-frequency", &val);
> > + if (val != IMX258_INPUT_CLOCK_FREQ)
> > + return -EINVAL;
> > + } else if (IS_ERR(imx258->clk)) {
> > + return dev_err_probe(&client->dev, PTR_ERR(imx258->clk),
> > + "error getting clock\n");
> > + } else {
> > + if (clk_get_rate(imx258->clk) != IMX258_INPUT_CLOCK_FREQ) {
> > + dev_err(&client->dev,
> > + "input clock frequency not supported\n");
> > + return -EINVAL;
> > + }
> > + }
> >
> > /*
> > * Check that the device is mounted upside down. The driver only
> > @@ -1211,24 +1259,25 @@ static int imx258_probe(struct i2c_client *client)
> > if (ret || val != 180)
> > return -EINVAL;
> >
> > - imx258 = devm_kzalloc(&client->dev, sizeof(*imx258), GFP_KERNEL);
> > - if (!imx258)
> > - return -ENOMEM;
> > -
> > /* Initialize subdev */
> > v4l2_i2c_subdev_init(&imx258->sd, client, &imx258_subdev_ops);
> >
> > + /* Will be powered off via pm_runtime_idle */
> > + ret = imx258_power_on(&client->dev);
> > + if (ret)
> > + return ret;
> > +
> > /* Check module identity */
> > ret = imx258_identify_module(imx258);
> > if (ret)
> > - return ret;
> > + goto error_identify;
> >
> > /* Set default mode to max resolution */
> > imx258->cur_mode = &supported_modes[0];
> >
> > ret = imx258_init_controls(imx258);
> > if (ret)
> > - return ret;
> > + goto error_identify;
> >
> > /* Initialize subdev */
> > imx258->sd.internal_ops = &imx258_internal_ops;
> > @@ -1258,6 +1307,9 @@ static int imx258_probe(struct i2c_client *client)
> > error_handler_free:
> > imx258_free_controls(imx258);
> >
> > +error_identify:
> > + imx258_power_off(&client->dev);
>
> You'll need this in remove callback, too.

True, there is no runtime idle call so this is missing.

Thanks.

Best regards,
Krzysztof

\
 
 \ /
  Last update: 2020-09-29 11:24    [W:0.105 / U:2.728 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site