lkml.org 
[lkml]   [2020]   [Sep]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 7/7] arm64: dts: marvell: Add a device tree for the iEi Puzzle-M801 board
Date
Add initial support for the iEi Puzzle-M801 1U Rackmount Network
Appliance board.

The board is based on the quad-core Marvell Armada 8040 SoC and supports
up to 16 GB of DDR4 2400 MHz ECC RAM. It has a PCIe x16 slot (x2 lanes
only) and an M.2 type B slot.

Main system hardware:
2x USB 3.0
4x Gigabit Ethernet
2x SFP+
1x SATA 3.0
1x M.2 type B
1x RJ45 UART
1x SPI flash
1x iEi WT61P803 PUZZLE Microcontroller
1x EPSON RX8010 RTC (used instead of the integrated Marvell RTC controller)
6x SFP+ LED
1x HDD LED

All of the hardware listed above is supported and tested in this port.

Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Robert Marko <robert.marko@sartura.hr>
---
arch/arm64/boot/dts/marvell/Makefile | 1 +
.../dts/marvell/armada-8040-puzzle-m801.dts | 524 ++++++++++++++++++
2 files changed, 525 insertions(+)
create mode 100644 arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts

diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 3e5f2e7a040c..e413c3261792 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -12,6 +12,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-clearfog-gt-8k.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-puzzle-m801.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb
diff --git a/arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts b/arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts
new file mode 100644
index 000000000000..f1dd09ed22e9
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts
@@ -0,0 +1,524 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2016 Marvell Technology Group Ltd.
+ * Copyright (C) 2020 Sartura Ltd.
+ *
+ * Device Tree file for iEi Puzzle-M801
+ */
+
+#include "armada-8040.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "iEi-Puzzle-M801";
+ compatible = "marvell,armada8040", "marvell,armada-ap806-quad", "marvell,armada-ap806";
+
+ aliases {
+ ethernet0 = &cp0_eth0;
+ ethernet1 = &cp1_eth0;
+ ethernet2 = &cp0_eth1;
+ ethernet3 = &cp0_eth2;
+ ethernet4 = &cp1_eth1;
+ ethernet5 = &cp1_eth2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ /* Regulator labels correspond with schematics */
+ v_3_3: regulator-3-3v {
+ compatible = "regulator-fixed";
+ regulator-name = "v_3_3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ status = "okay";
+ };
+
+ v_5v0_usb3_hst_vbus: regulator-usb3-vbus0 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&cp0_gpio2 15 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_xhci_vbus_pins>;
+ regulator-name = "v_5v0_usb3_hst_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ status = "okay";
+ };
+
+ v_vddo_h: regulator-1-8v {
+ compatible = "regulator-fixed";
+ regulator-name = "v_vddo_h";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ status = "okay";
+ };
+
+ sfp_cp0_eth0: sfp-cp0-eth0 {
+ compatible = "sff,sfp";
+ i2c-bus = <&sfpplus0_i2c>;
+ los-gpio = <&sfpplus_gpio 11 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&sfpplus_gpio 10 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&sfpplus_gpio 9 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&sfpplus_gpio 8 GPIO_ACTIVE_HIGH>;
+ maximum-power-milliwatt = <3000>;
+ };
+
+ sfp_cp1_eth0: sfp-cp1-eth0 {
+ compatible = "sff,sfp";
+ i2c-bus = <&sfpplus1_i2c>;
+ los-gpio = <&sfpplus_gpio 3 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&sfpplus_gpio 2 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&sfpplus_gpio 1 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&sfpplus_gpio 0 GPIO_ACTIVE_HIGH>;
+ maximum-power-milliwatt = <3000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ status = "okay";
+ pinctrl-0 = <&cp0_sfpplus_led_pins &cp1_sfpplus_led_pins>;
+ pinctrl-names = "default";
+
+ led-0 {
+ /* SFP+ port 2: Activity */
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <0>;
+ gpios = <&cp1_gpio1 6 GPIO_ACTIVE_LOW>;
+ };
+
+ led-1 {
+ /* SFP+ port 1: Activity */
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <1>;
+ gpios = <&cp1_gpio1 14 GPIO_ACTIVE_LOW>;
+ };
+
+ led-2 {
+ /* SFP+ port 2: 10 Gbps indicator */
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <2>;
+ gpios = <&cp1_gpio1 7 GPIO_ACTIVE_LOW>;
+ };
+
+ led-3 {
+ /* SFP+ port 2: 1 Gbps indicator */
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <3>;
+ gpios = <&cp1_gpio1 8 GPIO_ACTIVE_LOW>;
+ };
+
+ led-4 {
+ /* SFP+ port 1: 10 Gbps indicator */
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <4>;
+ gpios = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>;
+ };
+
+ led-5 {
+ /* SFP+ port 1: 1 Gbps indicator */
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <5>;
+ gpios = <&cp1_gpio1 31 GPIO_ACTIVE_LOW>;
+ };
+
+ led-6 {
+ function = LED_FUNCTION_DISK;
+ linux,default-trigger = "disk-activity";
+ gpios = <&cp0_gpio2 22 GPIO_ACTIVE_HIGH>;
+ };
+
+ };
+};
+
+&ap_sdhci0 {
+ bus-width = <8>;
+ /*
+ * Not stable in HS modes - phy needs "more calibration", so add
+ * the "slow-mode" and disable SDR104, SDR50 and DDR50 modes.
+ */
+ marvell,xenon-phy-slow-mode;
+ no-1-8-v;
+ no-sd;
+ no-sdio;
+ non-removable;
+ status = "okay";
+ vqmmc-supply = <&v_vddo_h>;
+};
+
+&ap_thermal_cpu1 {
+ trips {
+ cpu_active: cpu-active {
+ temperature = <44000>;
+ hysteresis = <2000>;
+ type = "active";
+ };
+ };
+ cooling-maps {
+ fan-map {
+ trip = <&cpu_active>;
+ cooling-device = <&chassis_fan_group0 64 THERMAL_NO_LIMIT>,
+ <&chassis_fan_group1 64 THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&i2c0 {
+ clock-frequency = <100000>;
+ status = "okay";
+
+ rtc@32 {
+ compatible = "epson,rx8010";
+ reg = <0x32>;
+ };
+};
+
+&spi0 {
+ status = "okay";
+ spi-flash@0 {
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-max-frequency = <20000000>;
+ partition@u-boot {
+ label = "u-boot";
+ reg = <0x00000000 0x001f0000>;
+ };
+ partition@u-boot-env {
+ label = "u-boot-env";
+ reg = <0x001f0000 0x00010000>;
+ };
+ partition@ubi1 {
+ label = "ubi1";
+ reg = <0x00200000 0x03f00000>;
+ };
+ partition@ubi2 {
+ label = "ubi2";
+ reg = <0x04100000 0x03f00000>;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+};
+
+&uart1 {
+ status = "okay";
+ /* iEi WT61P803 PUZZLE MCU Controller */
+ mcu {
+ compatible = "iei,wt61p803-puzzle";
+ current-speed = <115200>;
+ enable-beep;
+
+ leds {
+ compatible = "iei,wt61p803-puzzle-leds";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+ };
+
+ iei-wt61p803-puzzle-hwmon {
+ compatible = "iei,wt61p803-puzzle-hwmon";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ chassis_fan_group0:fan-group@0 {
+ #cooling-cells = <2>;
+ reg = <0x00>;
+ cooling-levels = <64 102 170 230 250>;
+ };
+
+ chassis_fan_group1:fan-group@1 {
+ #cooling-cells = <2>;
+ reg = <0x01>;
+ cooling-levels = <64 102 170 230 250>;
+ };
+ };
+ };
+};
+
+&cp0_rtc {
+ status = "disabled";
+};
+
+&cp0_i2c0 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_i2c0_pins>;
+ status = "okay";
+
+ sfpplus_gpio: gpio@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ eeprom@54 {
+ compatible = "atmel,24c04";
+ reg = <0x54>;
+ };
+};
+
+&cp0_i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_i2c1_pins>;
+ status = "okay";
+
+ i2c-switch@70 {
+ compatible = "nxp,pca9544";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+
+ sfpplus0_i2c: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ sfpplus1_i2c: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+};
+
+&cp0_uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_uart1_pins>;
+ status = "okay";
+};
+
+&cp0_mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "okay";
+
+ ge_phy2: ethernet-phy@0 {
+ reg = <0>;
+ };
+
+ ge_phy3: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&cp0_pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_pcie_pins>;
+ num-lanes = <1>;
+ num-viewport = <8>;
+ reset-gpios = <&cp0_gpio2 20 GPIO_ACTIVE_LOW>;
+ ranges = <0x82000000 0x0 0xc0000000 0x0 0xc0000000 0x0 0x20000000>;
+ phys = <&cp0_comphy0 0>;
+ phy-names = "cp0-pcie0-x1-phy";
+ status = "okay";
+};
+
+&cp0_pinctrl {
+ cp0_ge_mdio_pins: ge-mdio-pins {
+ marvell,pins = "mpp32", "mpp34";
+ marvell,function = "ge";
+ };
+ cp0_i2c1_pins: i2c1-pins {
+ marvell,pins = "mpp35", "mpp36";
+ marvell,function = "i2c1";
+ };
+ cp0_i2c0_pins: i2c0-pins {
+ marvell,pins = "mpp37", "mpp38";
+ marvell,function = "i2c0";
+ };
+ cp0_uart1_pins: uart1-pins {
+ marvell,pins = "mpp40", "mpp41";
+ marvell,function = "uart1";
+ };
+ cp0_xhci_vbus_pins: xhci0-vbus-pins {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ cp0_pcie_pins: pcie-pins {
+ marvell,pins = "mpp52";
+ marvell,function = "gpio";
+ };
+ cp0_sdhci_pins: sdhci-pins {
+ marvell,pins = "mpp55", "mpp56", "mpp57", "mpp58", "mpp59",
+ "mpp60", "mpp61";
+ marvell,function = "sdio";
+ };
+ cp0_sfpplus_led_pins: sfpplus-led-pins {
+ marvell,pins = "mpp54";
+ marvell,function = "gpio";
+ };
+};
+
+&cp0_ethernet {
+ status = "okay";
+};
+
+&cp0_eth0 {
+ status = "okay";
+ phy-mode = "10gbase-r";
+ phys = <&cp0_comphy4 0>;
+ local-mac-address = [ae 00 00 00 ff 00];
+ sfp = <&sfp_cp0_eth0>;
+ managed = "in-band-status";
+};
+
+&cp0_eth1 {
+ status = "okay";
+ phy = <&ge_phy2>;
+ phy-mode = "sgmii";
+ local-mac-address = [ae 00 00 00 ff 01];
+ phys = <&cp0_comphy3 1>;
+};
+
+&cp0_eth2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ phys = <&cp0_comphy1 2>;
+ local-mac-address = [ae 00 00 00 ff 02];
+ phy = <&ge_phy3>;
+};
+
+&cp0_sata0 {
+ status = "okay";
+
+ sata-port@0 {
+ phys = <&cp0_comphy2 0>;
+ phy-names = "cp0-sata0-0-phy";
+ };
+
+ sata-port@1 {
+ phys = <&cp0_comphy5 1>;
+ phy-names = "cp0-sata0-1-phy";
+ };
+};
+
+&cp0_sdhci0 {
+ broken-cd;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_sdhci_pins>;
+ status = "okay";
+ vqmmc-supply = <&v_3_3>;
+};
+
+&cp0_usb3_0 {
+ status = "okay";
+};
+
+&cp0_usb3_1 {
+ status = "okay";
+};
+
+&cp1_i2c0 {
+ clock-frequency = <100000>;
+ status = "disabled";
+};
+
+&cp1_i2c1 {
+ clock-frequency = <100000>;
+ status = "disabled";
+};
+
+&cp1_rtc {
+ status = "disabled";
+};
+
+&cp1_ethernet {
+ status = "okay";
+};
+
+&cp1_eth0 {
+ status = "okay";
+ phy-mode = "10gbase-r";
+ phys = <&cp1_comphy4 0>;
+ local-mac-address = [ae 00 00 00 ff 03];
+ sfp = <&sfp_cp1_eth0>;
+ managed = "in-band-status";
+};
+
+&cp1_eth1 {
+ status = "okay";
+ phy = <&ge_phy4>;
+ phy-mode = "sgmii";
+ local-mac-address = [ae 00 00 00 ff 04];
+ phys = <&cp1_comphy3 1>;
+};
+
+&cp1_eth2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ local-mac-address = [ae 00 00 00 ff 05];
+ phys = <&cp1_comphy5 2>;
+ phy = <&ge_phy5>;
+};
+
+&cp1_pinctrl {
+ cp1_sfpplus_led_pins: sfpplus-led-pins {
+ marvell,pins = "mpp6", "mpp7", "mpp8", "mpp10", "mpp14", "mpp31";
+ marvell,function = "gpio";
+ };
+};
+
+&cp1_uart0 {
+ status = "disabled";
+};
+
+&cp1_comphy2 {
+ cp1_usbh0_con: connector {
+ compatible = "usb-a-connector";
+ phy-supply = <&v_5v0_usb3_hst_vbus>;
+ };
+};
+
+&cp1_usb3_0 {
+ phys = <&cp1_comphy2 0>;
+ phy-names = "cp1-usb3h0-comphy";
+ status = "okay";
+};
+
+&cp1_mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "okay";
+
+ ge_phy4: ethernet-phy@1 {
+ reg = <1>;
+ };
+ ge_phy5: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+&cp1_pcie0 {
+ num-lanes = <2>;
+ phys = <&cp1_comphy0 0>, <&cp1_comphy1 0>;
+ phy-names = "cp1-pcie0-x2-lane0-phy", "cp1-pcie0-x2-lane1-phy";
+ status = "okay";
+};
--
2.26.2
\
 
 \ /
  Last update: 2020-09-30 03:42    [W:0.129 / U:6.092 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site