lkml.org 
[lkml]   [2020]   [Sep]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH net-next 2/3] net: dp83869: Add ability to advertise Fiber connection
Date
Add the ability to advertise the Fiber connection if the strap or the
op-mode is configured for 100Base-FX.

Auto negotiation is not supported on this PHY when in fiber mode.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
---
drivers/net/phy/dp83869.c | 73 +++++++++++++++++++++++++++++++++++++++
1 file changed, 73 insertions(+)

diff --git a/drivers/net/phy/dp83869.c b/drivers/net/phy/dp83869.c
index 6b98d74b5102..81899bc99add 100644
--- a/drivers/net/phy/dp83869.c
+++ b/drivers/net/phy/dp83869.c
@@ -52,6 +52,10 @@
BMCR_FULLDPLX | \
BMCR_SPEED1000)

+#define MII_DP83869_FIBER_ADVERTISE (ADVERTISED_FIBRE | \
+ ADVERTISED_Pause | \
+ ADVERTISED_Asym_Pause)
+
/* This is the same bit mask as the BMCR so re-use the BMCR default */
#define DP83869_FX_CTRL_DEFAULT MII_DP83869_BMCR_DEFAULT

@@ -118,6 +122,28 @@ struct dp83869_private {
int mode;
};

+static int dp83869_read_status(struct phy_device *phydev)
+{
+ struct dp83869_private *dp83869 = phydev->priv;
+ int ret;
+
+ ret = genphy_read_status(phydev);
+ if (ret)
+ return ret;
+
+ if (linkmode_test_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported)) {
+ if (phydev->link) {
+ if (dp83869->mode == DP83869_RGMII_100_BASE)
+ phydev->speed = SPEED_100;
+ } else {
+ phydev->speed = SPEED_UNKNOWN;
+ phydev->duplex = DUPLEX_UNKNOWN;
+ }
+ }
+
+ return 0;
+}
+
static int dp83869_ack_interrupt(struct phy_device *phydev)
{
int err = phy_read(phydev, MII_DP83869_ISR);
@@ -295,6 +321,51 @@ static int dp83869_configure_rgmii(struct phy_device *phydev,
return ret;
}

+static int dp83869_configure_fiber(struct phy_device *phydev,
+ struct dp83869_private *dp83869)
+{
+ int bmcr;
+ int ret;
+
+ /* Only allow advertising what this PHY supports */
+ linkmode_and(phydev->advertising, phydev->advertising,
+ phydev->supported);
+
+ linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported);
+ linkmode_set_bit(ADVERTISED_FIBRE, phydev->advertising);
+
+ if (dp83869->mode == DP83869_RGMII_1000_BASE) {
+ linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
+ phydev->supported);
+ } else {
+ linkmode_set_bit(ETHTOOL_LINK_MODE_100baseFX_Full_BIT,
+ phydev->supported);
+ linkmode_set_bit(ETHTOOL_LINK_MODE_100baseFX_Half_BIT,
+ phydev->supported);
+
+ /* Auto neg is not supported in 100base FX mode */
+ bmcr = phy_read(phydev, MII_BMCR);
+ if (bmcr < 0)
+ return bmcr;
+
+ phydev->autoneg = AUTONEG_DISABLE;
+ linkmode_clear_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->supported);
+ linkmode_clear_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->advertising);
+
+ if (bmcr & BMCR_ANENABLE) {
+ ret = phy_modify(phydev, MII_BMCR, BMCR_ANENABLE, 0);
+ if (ret < 0)
+ return ret;
+ }
+ }
+
+ /* Update advertising from supported */
+ linkmode_or(phydev->advertising, phydev->advertising,
+ phydev->supported);
+
+ return 0;
+}
+
static int dp83869_configure_mode(struct phy_device *phydev,
struct dp83869_private *dp83869)
{
@@ -384,6 +455,7 @@ static int dp83869_configure_mode(struct phy_device *phydev,
break;
case DP83869_RGMII_1000_BASE:
case DP83869_RGMII_100_BASE:
+ ret = dp83869_configure_fiber(phydev, dp83869);
break;
default:
return -EINVAL;
@@ -494,6 +566,7 @@ static struct phy_driver dp83869_driver[] = {
/* IRQ related */
.ack_interrupt = dp83869_ack_interrupt,
.config_intr = dp83869_config_intr,
+ .read_status = dp83869_read_status,

.suspend = genphy_suspend,
.resume = genphy_resume,
--
2.28.0
\
 
 \ /
  Last update: 2020-09-15 20:27    [W:0.129 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site