lkml.org 
[lkml]   [2020]   [Sep]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v10 3/5] drivers/soc/litex: add LiteX SoC Controller driver
On Mon, Sep 14, 2020 at 3:24 PM Stafford Horne <shorne@gmail.com> wrote:
>
> On Mon, Sep 14, 2020 at 12:33:11PM +0200, Mateusz Holenko wrote:
> > On Fri, Sep 11, 2020 at 2:57 AM Stafford Horne <shorne@gmail.com> wrote:
> > >
> > > On Wed, Aug 12, 2020 at 02:34:34PM +0200, Mateusz Holenko wrote:
> > > > From: Pawel Czarnecki <pczarnecki@internships.antmicro.com>
> > > >
> > > > This commit adds driver for the FPGA-based LiteX SoC
> > > > Controller from LiteX SoC builder.
> > > >
> > > > Co-developed-by: Mateusz Holenko <mholenko@antmicro.com>
> > > > Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
> > > > Signed-off-by: Pawel Czarnecki <pczarnecki@internships.antmicro.com>
> > > > ---
> > > > + node = dev->of_node;
> > > > + if (!node)
> > > > + return -ENODEV;
>
> We return here without BUG() if the setup fails.
>
> > > > +
> > > > + soc_ctrl_dev = devm_kzalloc(dev, sizeof(*soc_ctrl_dev), GFP_KERNEL);
> > > > + if (!soc_ctrl_dev)
> > > > + return -ENOMEM;
>
> We return here without BUG() if we are out of memory.
>
> > > > +
> > > > + soc_ctrl_dev->base = devm_platform_ioremap_resource(pdev, 0);
> > > > + if (IS_ERR(soc_ctrl_dev->base))
> > > > + return PTR_ERR(soc_ctrl_dev->base);
>
> Etc.

You are totally right - this is not consistent.
We should probably either trigger BUG() in each case or don't bother at all.

>
> > > > +
> > > > + result = litex_check_csr_access(soc_ctrl_dev->base);
> > > > + if (result) {
> > > > + // LiteX CSRs access is broken which means that
> > > > + // none of LiteX drivers will most probably
> > > > + // operate correctly
> > > The comment format here with // is not usually used in the kernel, but its not
> > > forbidded. Could you use the /* */ multiline style?
> >
> > Sure, I'll change the commenting style here.
> >
> > >
> > > > + BUG();
> > > Instead of stopping the system with BUG, could we just do:
> > >
> > > return litex_check_csr_access(soc_ctrl_dev->base);
> > >
> > > We already have failure for NODEV/NOMEM so might as well not call BUG() here
> > > too.
> >
> > It's true that litex_check_csr_accessors() already generates error
> > codes that could be
> > returned directly.
> > The point of using BUG() macro here, however, is to stop booting the
> > system so that it's visible
> > (and impossible to miss for the user) that an unresolvable HW issue
> > was encountered.
> >
> > CSR-accessors - the litex_{g,s}et_reg() functions - are intended to be
> > used by other LiteX drivers
> > and it's very unlikely that those drivers would work properly after
> > the fail of litex_check_csr_accessors().
> > Since in such case the UART driver will be affected too (no boot logs
> > and error messages visible to the user),
> > I thought it'll be easier to spot and debug the problem if the system
> > stopped in the BUG loop.
> > Perhaps there are other, more linux-friendly, ways of achieving a
> > similar goal - I'm open for suggestions.
>
> I see your point, but I thought if failed with an exit status above, we could do
> the same here. But I guess failing here means that something is really wrong as
> validation failed.
>
> Some points:
> - If we return here, the system will still boot but there will be no UART
> - If we bail with BUG(), here the system stops, and there is no UART
> - Both cases the user can connect with a debugger and read "dmesg", to see what
> is wrong, but BUG() does not print an error message on all architectures.
>
> We could also use:
>
> - WARN(1, "Failed to validate CSR registers, the system is probably broken.");
>
> If you want to keep BUG() it may be fine.
>
> I am not an expert on handling these type of bailout's so other input is
> appreciated.

I don't have a strong opinion about using BUG() here - I just thought
it would be easier for the user.
If this is, however, not how linux typically works, I'm ok with
reworking this part.

> -Stafford

Best,
Mateusz

--
Mateusz Holenko
Antmicro Ltd | www.antmicro.com
Roosevelta 22, 60-829 Poznan, Poland

\
 
 \ /
  Last update: 2020-09-16 02:46    [W:0.055 / U:1.204 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site