lkml.org 
[lkml]   [2020]   [Sep]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] drm/bridge: dw-mipi-dsi: permit configuring the escape clock rate
From
Date
On 11/09/2020 10:29, Philippe CORNU wrote:
>
>
> On 9/4/20 2:55 PM, Neil Armstrong wrote:
>> The Amlogic D-PHY in the Amlogic AXG SoC Family does support a frequency
>> higher than 10MHz for the TX Escape Clock, thus make the target rate
>> configurable.
>>
>> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
>> ---
>> drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 25 +++++++++++++++----
>> include/drm/bridge/dw_mipi_dsi.h | 1 +
>> 2 files changed, 21 insertions(+), 5 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
>> index d580b2aa4ce9..31fc965c66fd 100644
>> --- a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
>> +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
>> @@ -562,15 +562,30 @@ static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi)
>>
>> static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
>> {
>> + const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops;
>> + unsigned int esc_rate; /* in MHz */
>> + u32 esc_clk_division;
>> + int ret;
>> +
>> /*
>> * The maximum permitted escape clock is 20MHz and it is derived from
>> - * lanebyteclk, which is running at "lane_mbps / 8". Thus we want:
>> - *
>> - * (lane_mbps >> 3) / esc_clk_division < 20
>> + * lanebyteclk, which is running at "lane_mbps / 8".
>> + */
>> + if (phy_ops->get_esc_clk_rate) {
>> + ret = phy_ops->get_esc_clk_rate(dsi->plat_data->priv_data,
>> + &esc_rate);
>> + if (ret)
>> + DRM_DEBUG_DRIVER("Phy get_esc_clk_rate() failed\n");
>> + } else
>> + esc_rate = 20; /* Default to 20MHz */
>> +
>> + /*
>> + * We want :
>> + * (lane_mbps >> 3) / esc_clk_division < X
>> * which is:
>> - * (lane_mbps >> 3) / 20 > esc_clk_division
>> + * (lane_mbps >> 3) / X > esc_clk_division
>> */
>> - u32 esc_clk_division = (dsi->lane_mbps >> 3) / 20 + 1;
>> + esc_clk_division = (dsi->lane_mbps >> 3) / esc_rate + 1;
>>
>> dsi_write(dsi, DSI_PWR_UP, RESET);
>>
>> diff --git a/include/drm/bridge/dw_mipi_dsi.h b/include/drm/bridge/dw_mipi_dsi.h
>> index b0e390b3288e..bda8aa7c2280 100644
>> --- a/include/drm/bridge/dw_mipi_dsi.h
>> +++ b/include/drm/bridge/dw_mipi_dsi.h
>> @@ -36,6 +36,7 @@ struct dw_mipi_dsi_phy_ops {
>> unsigned int *lane_mbps);
>> int (*get_timing)(void *priv_data, unsigned int lane_mbps,
>> struct dw_mipi_dsi_dphy_timing *timing);
>> + int (*get_esc_clk_rate)(void *priv_data, unsigned int *esc_clk_rate);
>> };
>>
>> struct dw_mipi_dsi_host_ops {
>>
>
> Hi Neil,
> Thank you for the patch
>
> Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
>
> Philippe :-)
>

Thanks !

Applying to drm-misc-next

Neil

\
 
 \ /
  Last update: 2020-09-11 16:52    [W:0.073 / U:0.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site