Messages in this thread | | | Date | Mon, 31 Aug 2020 08:43:06 +0200 | From | Johan Hovold <> | Subject | Re: [PATCH] USB: serial: option: add support for SIM7070/SIM7080/SIM7090 modules |
| |
On Sat, Aug 29, 2020 at 11:05:39AM +0200, Aleksander Morgado wrote: > These modules have 2 different USB layouts: > > The default layout with PID 0x9205 (AT+CUSBSELNV=1) exposes 4 TTYs and > an ECM interface: > > T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 > D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 > P: Vendor=1e0e ProdID=9205 Rev=00.00 > S: Manufacturer=SimTech, Incorporated > S: Product=SimTech SIM7080 > S: SerialNumber=1234567890ABCDEF > C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA > I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether > I: If#=0x5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether > > The purpose of each TTY is as follows: > * ttyUSB0: DIAG/QCDM port. > * ttyUSB1: GNSS data. > * ttyUSB2: AT-capable port (control). > * ttyUSB3: AT-capable port (data). > > In the secondary layout with PID=0x9206 (AT+CUSBSELNV=86) the module > exposes 6 TTY ports: > > T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 8 Spd=480 MxCh= 0 > D: Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 > P: Vendor=1e0e ProdID=9206 Rev=00.00 > S: Manufacturer=SimTech, Incorporated > S: Product=SimTech SIM7080 > S: SerialNumber=1234567890ABCDEF > C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA > I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > > The purpose of each TTY is as follows: > * ttyUSB0: DIAG/QCDM port. > * ttyUSB1: GNSS data. > * ttyUSB2: AT-capable port (control). > * ttyUSB3: QFLOG interface. > * ttyUSB4: DAM interface. > * ttyUSB5: AT-capable port (data). > > Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Now applied. Thanks, Aleksander.
Johan
| |