lkml.org 
[lkml]   [2020]   [Aug]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH V2 2/3] arm64: dts: qcom: sc7180: Add sleep pin ctrl for BT uart
Hi Matthias,

On 2020-08-19 21:43, Matthias Kaehlcke wrote:
> On Wed, Aug 19, 2020 at 07:19:25PM +0530, skakit@codeaurora.org wrote:
>> On 2020-08-17 23:31, Matthias Kaehlcke wrote:
>> > On Fri, Jul 24, 2020 at 09:28:01AM +0530, satya priya wrote:
>> > > Add sleep pin ctrl for BT uart, and also change the bias
>> > > configuration to match Bluetooth module.
>> > >
>> > > Signed-off-by: satya priya <skakit@codeaurora.org>
>> > > ---
>> > > Changes in V2:
>> > > - This patch adds sleep state for BT UART. Newly added in V2.
>> > >
>> > > arch/arm64/boot/dts/qcom/sc7180-idp.dts | 42
>> > > ++++++++++++++++++++++++++++-----
>> > > 1 file changed, 36 insertions(+), 6 deletions(-)
>> > >
>> > > diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
>> > > b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
>> > > index 26cc491..bc919f2 100644
>> > > --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
>> > > +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
>> > > @@ -469,20 +469,50 @@
>> > >
>> > > &qup_uart3_default {
>> > > pinconf-cts {
>> > > - /*
>> > > - * Configure a pull-down on 38 (CTS) to match the pull of
>> > > - * the Bluetooth module.
>> > > - */
>> > > + /* Configure no pull on 38 (CTS) to match Bluetooth module */
>> >
>> > Has the pull from the Bluetooth module been removed or did the previous
>> > config
>> > incorrectly claim that the Bluetooth module has a pull-down?
>> >
>>
>> The previous config was incorrect, so we corrected it to match the
>> pull of
>> BT.
>
> The pull config of the BT controller varies depending on its state,
> could
> you clarify which state you intend to match?
>

Since this line is driven by BT SoC, they could change their
pull(although it's less likely). Recently on cherokee we worked with BT
team and came to an agreement to keep no-pull from our side in order to
not conflict with their pull in any state.

>>
>> > > pins = "gpio38";
>> > > + bias-disable;
>> > > + };
>> > > +
>> > > + pinconf-rts {
>> > > + /* We'll drive 39 (RTS), so configure pull-down */
>> > > + pins = "gpio39";
>> > > + drive-strength = <2>;
>> > > bias-pull-down;
>> > > + };
>> > > +
>> > > + pinconf-tx {
>> > > + /* We'll drive 40 (TX), so no pull */
>> >
>> > The rationales for RTS and TX contradict each other. According to the
>> > comment
>> > the reason to configure a pull-down on RTS is that it is driven by the
>> > host.
>> > Then for TX the reason to configure no pull is that it is driven by the
>> > host.
>> >
>> > Please make sure the comments *really* describe the rationale, otherwise
>> > they
>> > are just confusing.
>>
>> The rationale for RTS is that we don't want it to be floating and want
>> to
>> make sure that it is pulled down, to receive bytes. Will modify the
>> comment
>> mentioning the same.
>
> Could you clarify what you mean with "to receive bytes"?
>

When we keep no-pull(floating), sometimes it may be pulled high and UART
flow will be turned off(RFR_NOT_READY), due to this BT SoC wont be able
to send data even though host is ready.

> Thanks
>
> Matthias

Thanks,
Satya Priya

\
 
 \ /
  Last update: 2020-08-20 14:21    [W:0.893 / U:0.256 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site