lkml.org 
[lkml]   [2020]   [Aug]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 2/3] media: i2c: ov5640: Add support for BT656 mode
Date
Enable support for BT656 mode.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
---
drivers/media/i2c/ov5640.c | 46 ++++++++++++++++++++++++++++----------
1 file changed, 34 insertions(+), 12 deletions(-)

diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c
index e36bc08bc17f..160d2857352a 100644
--- a/drivers/media/i2c/ov5640.c
+++ b/drivers/media/i2c/ov5640.c
@@ -84,6 +84,7 @@
#define OV5640_REG_VFIFO_HSIZE 0x4602
#define OV5640_REG_VFIFO_VSIZE 0x4604
#define OV5640_REG_JPG_MODE_SELECT 0x4713
+#define OV5640_REG_CCIR656_CTRL00 0x4730
#define OV5640_REG_POLARITY_CTRL00 0x4740
#define OV5640_REG_MIPI_CTRL00 0x4800
#define OV5640_REG_DEBUG_MODE 0x4814
@@ -1215,6 +1216,20 @@ static int ov5640_set_autogain(struct ov5640_dev *sensor, bool on)
BIT(1), on ? 0 : BIT(1));
}

+static int ov5640_set_stream_bt656(struct ov5640_dev *sensor, bool on)
+{
+ int ret;
+
+ ret = ov5640_write_reg(sensor, OV5640_REG_CCIR656_CTRL00,
+ on ? 0x1 : 0x00);
+ if (ret)
+ return ret;
+
+ return ov5640_write_reg(sensor, OV5640_REG_SYS_CTRL0, on ?
+ OV5640_REG_SYS_CTRL0_SW_PWUP :
+ OV5640_REG_SYS_CTRL0_SW_PWDN);
+}
+
static int ov5640_set_stream_dvp(struct ov5640_dev *sensor, bool on)
{
return ov5640_write_reg(sensor, OV5640_REG_SYS_CTRL0, on ?
@@ -2022,18 +2037,21 @@ static int ov5640_set_power_dvp(struct ov5640_dev *sensor, bool on)
* datasheet and hardware, 0 is active high
* and 1 is active low...)
*/
- if (flags & V4L2_MBUS_PCLK_SAMPLE_RISING)
- pclk_pol = 1;
- if (flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH)
- hsync_pol = 1;
- if (flags & V4L2_MBUS_VSYNC_ACTIVE_LOW)
- vsync_pol = 1;
+ if (sensor->ep.bus_type == V4L2_MBUS_PARALLEL) {
+ if (flags & V4L2_MBUS_PCLK_SAMPLE_RISING)
+ pclk_pol = 1;
+ if (flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH)
+ hsync_pol = 1;
+ if (flags & V4L2_MBUS_VSYNC_ACTIVE_LOW)
+ vsync_pol = 1;
+
+ ret = ov5640_write_reg(sensor, OV5640_REG_POLARITY_CTRL00,
+ (pclk_pol << 5) | (hsync_pol << 1) |
+ vsync_pol);

- ret = ov5640_write_reg(sensor, OV5640_REG_POLARITY_CTRL00,
- (pclk_pol << 5) | (hsync_pol << 1) | vsync_pol);
-
- if (ret)
- return ret;
+ if (ret)
+ return ret;
+ }

/*
* powerdown MIPI TX/RX PHY & disable MIPI
@@ -2057,7 +2075,9 @@ static int ov5640_set_power_dvp(struct ov5640_dev *sensor, bool on)
* - 4: PCLK output enable
* - [3:0]: D[9:6] output enable
*/
- ret = ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT_ENABLE01, 0x7f);
+ ret = ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT_ENABLE01,
+ sensor->ep.bus_type == V4L2_MBUS_PARALLEL ?
+ 0x7f : 0x1f);
if (ret)
return ret;

@@ -2911,6 +2931,8 @@ static int ov5640_s_stream(struct v4l2_subdev *sd, int enable)

if (sensor->ep.bus_type == V4L2_MBUS_CSI2_DPHY)
ret = ov5640_set_stream_mipi(sensor, enable);
+ else if (sensor->ep.bus_type == V4L2_MBUS_BT656)
+ ret = ov5640_set_stream_bt656(sensor, enable);
else
ret = ov5640_set_stream_dvp(sensor, enable);

--
2.17.1
\
 
 \ /
  Last update: 2020-08-13 19:14    [W:0.065 / U:0.292 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site