lkml.org 
[lkml]   [2020]   [Aug]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH] serial: qcom_geni_serial: Fix recent kdb hang
From
Date
Hi Doug,

On 8/7/2020 10:49 AM, Douglas Anderson wrote:
> The commit e42d6c3ec0c7 ("serial: qcom_geni_serial: Make kgdb work
> even if UART isn't console") worked pretty well and I've been doing a
> lot of debugging with it. However, recently I typed "dmesg" in kdb
> and then held the space key down to scroll through the pagination. My
> device hung. This was repeatable and I found that it was introduced
> with the aforementioned commit.
>
> It turns out that there are some strange boundary cases in geni where
> in some weird situations it will signal RX_LAST but then will put 0 in
> RX_LAST_BYTE. This means that the entire last FIFO entry is valid.

IMO that means we received a word in RX_FIFO and it is the last word
hence RX_LAST bit is set.

RX_LAST_BYTE is 0 means none of the bytes are valid in the last word.

In such scenario we should just read RX_FIFO buffer (to empty it),
discard the word and return NO_POLL_CHAR. Something like below.

---------------------------------------------------------------------------------------------------------------------------------------------------------

                else
                        private_data->poll_cached_bytes_cnt = 4;

                private_data->poll_cached_bytes =
                        readl(uport->membase + SE_GENI_RX_FIFOn);
        }

+        if (!private_data->poll_cached_bytes_cnt)
+              return NO_POLL_CHAR;
        private_data->poll_cached_bytes_cnt--;
        ret = private_data->poll_cached_bytes & 0xff;
-------------------------------------------------------------------------------------------------------------------------------------------------------------

Please let me know whether above code helps.

I am not sure about what all scenario can leads to this behavior from
hardware, I will try to get an answer from hardware team.

Any error bit was set for SE_GENI_S_IRQ_STATUS & SE_GENI_M_IRQ_STATUS
registers?


I guess the hang was seen because *poll_cached_bytes_cnt* is unsigned
int and it's value was 0, when it's decremented by 1 it's value become
'4294967295' (very large) and dummy RX (0x00) would happen that

many times before reading any actual RX transfers/bytes.

Regards,

Akash


> This weird corner case is handled in qcom_geni_serial_handle_rx()
> where you can see that we only honor RX_LAST_BYTE if RX_LAST is set
> _and_ RX_LAST_BYTE is non-zero. If either of these is not true we use
> BYTES_PER_FIFO_WORD (4) for the size of the last FIFO word.
>
> Let's fix kgdb. While at it, also use the proper #define for 4.
>
> Fixes: e42d6c3ec0c7 ("serial: qcom_geni_serial: Make kgdb work even if UART isn't console")
> Signed-off-by: Douglas Anderson <dianders@chromium.org>
> ---
>
> drivers/tty/serial/qcom_geni_serial.c | 9 +++++++--
> 1 file changed, 7 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/tty/serial/qcom_geni_serial.c b/drivers/tty/serial/qcom_geni_serial.c
> index 07b7b6b05b8b..e27077656939 100644
> --- a/drivers/tty/serial/qcom_geni_serial.c
> +++ b/drivers/tty/serial/qcom_geni_serial.c
> @@ -361,11 +361,16 @@ static int qcom_geni_serial_get_char(struct uart_port *uport)
> return NO_POLL_CHAR;
>
> if (word_cnt == 1 && (status & RX_LAST))
> + /*
> + * NOTE: If RX_LAST_BYTE_VALID is 0 it needs to be
> + * treated as if it was BYTES_PER_FIFO_WORD.
> + */
> private_data->poll_cached_bytes_cnt =
> (status & RX_LAST_BYTE_VALID_MSK) >>
> RX_LAST_BYTE_VALID_SHFT;
> - else
> - private_data->poll_cached_bytes_cnt = 4;
> +
> + if (private_data->poll_cached_bytes_cnt == 0)
> + private_data->poll_cached_bytes_cnt = BYTES_PER_FIFO_WORD;
>
> private_data->poll_cached_bytes =
> readl(uport->membase + SE_GENI_RX_FIFOn);

--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,\na Linux Foundation Collaborative Project

\
 
 \ /
  Last update: 2020-08-10 14:33    [W:0.114 / U:0.324 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site