lkml.org 
[lkml]   [2020]   [Jul]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 1/2] dt-bindings: dma: Add bindings for intel LGM SOC
Date
Add DT bindings YAML schema for DMA controller driver
of Lightning Mountain(LGM) SoC.

Signed-off-by: Amireddy Mallikarjuna reddy <mallikarjunax.reddy@linux.intel.com>
---
v1:
- Initial version.

v2:
- Fix bot errors.

v3:
- No change.

v4:
- Address Thomas langer comments
---
.../devicetree/bindings/dma/intel,ldma.yaml | 416 +++++++++++++++++++++
1 file changed, 416 insertions(+)
create mode 100644 Documentation/devicetree/bindings/dma/intel,ldma.yaml

diff --git a/Documentation/devicetree/bindings/dma/intel,ldma.yaml b/Documentation/devicetree/bindings/dma/intel,ldma.yaml
new file mode 100644
index 000000000000..7f666b9812e4
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/intel,ldma.yaml
@@ -0,0 +1,416 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/dma/intel,ldma.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lightning Mountain centralized low speed DMA and high speed DMA controllers.
+
+maintainers:
+ - chuanhua.lei@intel.com
+ - mallikarjunax.reddy@intel.com
+
+properties:
+ $nodename:
+ pattern: "^dma(@.*)?$"
+
+ "#dma-cells":
+ const: 1
+
+ compatible:
+ anyOf:
+ - const: intel,lgm-cdma
+ - const: intel,lgm-dma2tx
+ - const: intel,lgm-dma1rx
+ - const: intel,lgm-dma1tx
+ - const: intel,lgm-dma0tx
+ - const: intel,lgm-dma3
+ - const: intel,lgm-toe-dma30
+ - const: intel,lgm-toe-dma31
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ intel,dma-poll-cnt:
+ $ref: /schemas/types.yaml#definitions/uint32
+ description:
+ DMA descriptor polling counter. It may need fine tune according
+ to the system application scenario.
+
+ intel,dma-byte-en:
+ type: boolean
+ description:
+ DMA byte enable is only valid for DMA write(RX).
+ Byte enable(1) means DMA write will be based on the number of dwords
+ instead of the whole burst.
+
+ intel,dma-drb:
+ type: boolean
+ description:
+ DMA descriptor read back to make sure data and desc synchronization.
+
+ intel,dma-burst:
+ $ref: /schemas/types.yaml#definitions/uint32
+ description:
+ Specifiy the DMA burst size(in dwords), the valid value will be 8, 16, 32.
+ Default is 16 for data path dma, 32 is for memcopy DMA.
+
+ intel,dma-polling-cnt:
+ $ref: /schemas/types.yaml#definitions/uint32
+ description:
+ DMA descriptor polling counter. It may need fine tune according to
+ the system application scenario.
+
+ intel,dma-desc-in-sram:
+ type: boolean
+ description:
+ DMA descritpors in SRAM or not. Some old controllers descriptors
+ can be in DRAM or SRAM. The new ones are all in SRAM.
+
+ intel,dma-orrc:
+ $ref: /schemas/types.yaml#definitions/uint32
+ description:
+ DMA outstanding read counter. The maximum value is 16, and it may
+ need fine tune according to the system application scenarios.
+
+ intel,dma-dburst-wr:
+ type: boolean
+ description:
+ Enable RX dynamic burst write. It only applies to RX DMA and memcopy DMA.
+
+
+ dma-ports:
+ type: object
+ description:
+ This sub-node must contain a sub-node for each DMA port.
+ properties:
+ '#address-cells':
+ const: 1
+ '#size-cells':
+ const: 0
+
+ patternProperties:
+ "^dma-ports@[0-9]+$":
+ type: object
+
+ properties:
+ reg:
+ items:
+ - enum: [0, 1, 2, 3, 4, 5]
+ description:
+ Which port this node refers to.
+
+ intel,name:
+ $ref: /schemas/types.yaml#definitions/string-array
+ description:
+ Port name of each DMA port.
+
+ intel,chans:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description:
+ The channels included on this port. Format is channel start
+ number and how many channels on this port.
+
+ intel,burst:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Specify the DMA port burst size, the valid value will be
+ 2, 4, 8. Default is 2 for data path dma.
+
+ intel,txwgt:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Specify the port transmit weight for QoS purpose. The valid
+ value is 1~7. Default value is 1.
+
+ intel,endian:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Specify the DMA port endiannes conversion due to SoC endianness difference.
+
+ required:
+ - reg
+ - intel,name
+ - intel,chans
+
+
+ dma-channels:
+ type: object
+ description:
+ This sub-node must contain a sub-node for each DMA channel.
+ properties:
+ '#address-cells':
+ const: 1
+ '#size-cells':
+ const: 0
+
+ patternProperties:
+ "^dma-channels@[0-9]+$":
+ type: object
+
+ properties:
+ reg:
+ items:
+ - enum: [0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15]
+ description:
+ Which channel this node refers to.
+
+ intel,desc_num:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Per channel maximum descriptor number. The max value is 255.
+
+ intel,pkt_sz:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Channel buffer packet size. It must be power of 2.
+ The maximum size is 4096.
+
+ intel,desc-rx-nonpost:
+ type: boolean
+ description:
+ Write non-posted type for DMA RX last data beat of every descriptor.
+
+ intel,data-endian:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Per channel data endianness configuration according to SoC requirement.
+
+ intel,desc-endian:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Per channel descriptor endianness configuration according to SoC requirement.
+
+ intel,data-endian-en:
+ type: boolean
+ description:
+ Per channel data endianness enabled.
+
+ intel,desc-endian-en:
+ type: boolean
+ description:
+ Per channel descriptor endianness enabled.
+
+ intel,byte-offset:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Per channel byte offset(0~128).
+
+ intel,hdr-mode:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description:
+ The first parameter is header mode size, the second
+ parameter is checksum enable or disable. If enabled,
+ header mode size is ignored. If disabled, header mode
+ size must be provided.
+
+ intel,non-arb-cnt:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Per channel non arbitration counter while polling
+
+ intel,arb-cnt:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Per channel arbitration counter while polling.
+ arb_cnt must be greater than non_arb_cnt
+
+ intel,pkt-drop:
+ type: boolean
+ description:
+ Channel packet drop enabled or disabled.
+
+ intel,hw-desc:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description:
+ Per channel dma hardware descriptor configuration.
+ The first parameter is descriptor physical address and the
+ second parameter hardware descriptor number.
+
+ required:
+ - reg
+
+required:
+ - compatible
+ - reg
+ - '#dma-cells'
+
+examples:
+ - |
+ dma0: dma@e0e00000 {
+ compatible = "intel,lgm-cdma";
+ reg = <0xe0e00000 0x1000>;
+ #dma-cells = <1>;
+ interrupt-parent = <&ioapic1>;
+ interrupts = <82 1>;
+ resets = <&rcu0 0x30 0>;
+ reset-names = "ctrl";
+ clocks = <&cgu0 80>;
+ intel,dma-poll-cnt = <4>;
+ intel,dma-byte-en;
+ intel,dma-drb;
+ dma-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dma-ports@0 {
+ reg = <0>;
+ intel,name = "SPI0";
+ intel,chans = <0 2>;
+ intel,burst = <2>;
+ intel,txwgt = <1>;
+ };
+ dma-ports@1 {
+ reg = <1>;
+ intel,name = "SPI1";
+ intel,chans = <2 2>;
+ intel,burst = <2>;
+ intel,txwgt = <1>;
+ };
+ dma-ports@2 {
+ reg = <2>;
+ intel,name = "SPI2";
+ intel,chans = <4 2>;
+ intel,burst = <2>;
+ intel,txwgt = <1>;
+ };
+ dma-ports@3 {
+ reg = <3>;
+ intel,name = "SPI3";
+ intel,chans = <6 2>;
+ intel,burst = <2>;
+ intel,endian = <0>;
+ intel,txwgt = <1>;
+ };
+ dma-ports@4 {
+ reg = <4>;
+ intel,name = "HSNAND";
+ intel,chans = <8 2>;
+ intel,burst = <8>;
+ intel,txwgt = <1>;
+ };
+ dma-ports@5 {
+ reg = <5>;
+ intel,name = "PCM";
+ intel,chans = <10 6>;
+ intel,burst = <8>;
+ intel,txwgt = <1>;
+ };
+ };
+ dma-channels {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dma-channels@0 {
+ reg = <0>;
+ intel,desc_num = <1>;
+ };
+ dma-channels@1 {
+ reg = <1>;
+ intel,desc_num = <1>;
+ };
+ dma-channels@2 {
+ reg = <2>;
+ intel,desc_num = <1>;
+ };
+ dma-channels@3 {
+ reg = <3>;
+ intel,desc_num = <1>;
+ };
+ dma-channels@4 {
+ reg = <4>;
+ intel,desc_num = <1>;
+ };
+ dma-channels@5 {
+ reg = <5>;
+ intel,desc_num = <1>;
+ };
+ dma-channels@6 {
+ reg = <6>;
+ intel,desc_num = <1>;
+ };
+ dma-channels@7 {
+ reg = <7>;
+ intel,desc_num = <1>;
+ };
+ dma-channels@8 {
+ reg = <8>;
+ };
+ dma-channels@9 {
+ reg = <9>;
+ };
+ dma-channels@10 {
+ reg = <10>;
+ };
+ dma-channels@11 {
+ reg = <11>;
+ };
+ dma-channels@12 {
+ reg = <12>;
+ };
+ dma-channels@13 {
+ reg = <13>;
+ };
+ dma-channels@14 {
+ reg = <14>;
+ };
+ dma-channels@15 {
+ reg = <15>;
+ };
+ };
+ };
+ - |
+ dma3: dma@ec800000 {
+ compatible = "intel,lgm-dma3";
+ reg = <0xec800000 0x1000>;
+ clocks = <&cgu0 71>;
+ resets = <&rcu0 0x10 9>;
+ #dma-cells = <1>;
+ intel,dma-burst = <32>;
+ intel,dma-polling-cnt = <16>;
+ intel,dma-desc-in-sram;
+ intel,dma-orrc = <16>;
+ intel,dma-byte-en;
+ intel,dma-dburst-wr;
+ dma-channels {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dma-channels@12 {
+ reg = <12>;
+ intel,pkt_sz = <4096>;
+ intel,desc-rx-nonpost;
+ intel,data-endian = <0>;
+ intel,desc-endian = <0>;
+ intel,data-endian-en;
+ intel,desc-endian-en;
+ intel,byte-offset = <0>;
+ intel,hdr-mode = <128 0>;
+ intel,non-arb-cnt = <0>;
+ intel,arb-cnt = <0>;
+ intel,hw-desc = <0x20000000 8>;
+ };
+ dma-channels@13 {
+ reg = <13>;
+ intel,pkt-drop;
+ intel,pkt_sz = <4096>;
+ intel,data-endian = <0>;
+ intel,desc-endian = <0>;
+ intel,data-endian-en;
+ intel,desc-endian-en;
+ intel,byte-offset = <0>;
+ intel,hdr-mode = <128 0>;
+ intel,non-arb-cnt = <0>;
+ intel,arb-cnt = <0>;
+ };
+ };
+ };
--
2.11.0
\
 
 \ /
  Last update: 2020-07-09 08:04    [W:0.096 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site