lkml.org 
[lkml]   [2020]   [Jul]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RESEND PATCH v4 1/3] usb: serial: Add MaxLinear/Exar USB to Serial driver
Hi,

Sorry for the late reply!

On Wed, Jul 01, 2020 at 12:34:33PM +0200, Johan Hovold wrote:
> On Sun, Jun 07, 2020 at 09:53:48PM +0530, Manivannan Sadhasivam wrote:
> > Add support for MaxLinear/Exar USB to Serial converters. This driver
> > only supports XR21V141X series but it can be extended to other series
> > from Exar as well in future.
> >
> > This driver is inspired from the initial one submitted by Patong Yang:
> >
> > https://patchwork.kernel.org/patch/10543261/
>
> You've also copied code from that driver so you need to maintain its
> copyright as well.
>
> Probably better you link to lore than patchwork. Do that in the file
> header as well.
>
> > While the initial driver was a custom tty USB driver exposing whole
> > new serial interface ttyXRUSBn, this version is completely based on USB
> > serial core thus exposing the interfaces as ttyUSBn. This will avoid
> > the overhead of exposing a new USB serial interface which the userspace
> > tools are unaware of.
> >
> > Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> > Tested-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
> > Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
> > ---
> > drivers/usb/serial/Kconfig | 9 +
> > drivers/usb/serial/Makefile | 1 +
> > drivers/usb/serial/xr_serial.c | 650 +++++++++++++++++++++++++++++++++
> > 3 files changed, 660 insertions(+)
> > create mode 100644 drivers/usb/serial/xr_serial.c
> >
> > diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig
> > index 25d7e0c36d38..8f6ad9f94735 100644
> > --- a/drivers/usb/serial/Kconfig
> > +++ b/drivers/usb/serial/Kconfig
> > @@ -644,6 +644,15 @@ config USB_SERIAL_UPD78F0730
> > To compile this driver as a module, choose M here: the
> > module will be called upd78f0730.
> >
> > +config USB_SERIAL_XR
> > + tristate "USB MaxLinear/Exar USB to Serial driver"
> > + help
> > + Say Y here if you want to use MaxLinear/Exar USB to Serial converter
> > + devices.
> > +
> > + To compile this driver as a module, choose M here: the
> > + module will be called xr_serial.
> > +
> > config USB_SERIAL_DEBUG
> > tristate "USB Debugging Device"
> > help
> > diff --git a/drivers/usb/serial/Makefile b/drivers/usb/serial/Makefile
> > index 2d491e434f11..4f69c2a3aff3 100644
> > --- a/drivers/usb/serial/Makefile
> > +++ b/drivers/usb/serial/Makefile
> > @@ -62,4 +62,5 @@ obj-$(CONFIG_USB_SERIAL_VISOR) += visor.o
> > obj-$(CONFIG_USB_SERIAL_WISHBONE) += wishbone-serial.o
> > obj-$(CONFIG_USB_SERIAL_WHITEHEAT) += whiteheat.o
> > obj-$(CONFIG_USB_SERIAL_XIRCOM) += keyspan_pda.o
> > +obj-$(CONFIG_USB_SERIAL_XR) += xr_serial.o
> > obj-$(CONFIG_USB_SERIAL_XSENS_MT) += xsens_mt.o
> > diff --git a/drivers/usb/serial/xr_serial.c b/drivers/usb/serial/xr_serial.c
> > new file mode 100644
> > index 000000000000..bb7df79cc129
> > --- /dev/null
> > +++ b/drivers/usb/serial/xr_serial.c
> > @@ -0,0 +1,650 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * MaxLinear/Exar USB to Serial driver
> > + *
> > + * Based on initial driver written by Patong Yang <patong.mxl@gmail.com>
>
> Reproduce Patong Yang's copyright here as well.
>
> > + *
> > + * This driver claims both data and control interfaces but only registers tty
> > + * device for data interface.
>
> Not sure this is needed here; this is just the way CDC-ACM works.
>
> > + *
> > + * Copyright (c) 2020 Manivannan Sadhasivam <mani@kernel.org>
>
> Not your employer?
>
> > + */
> > +
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/slab.h>
> > +#include <linux/tty.h>
> > +#include <linux/usb.h>
> > +#include <linux/usb/serial.h>
> > +
> > +static void xr_set_termios(struct tty_struct *tty,
> > + struct usb_serial_port *port,
> > + struct ktermios *old_termios);
>
> Move set_termios() before open() so that you don't need this.
>
> > +
> > +struct xr_uart_regs {
> > + u8 enable;
> > + u8 format;
> > + u8 flow_ctrl;
> > + u8 xon_char;
> > + u8 xoff_char;
> > + u8 loopback;
> > + u8 tx_break;
> > + u8 rs485_delay;
> > + u8 gpio_mode;
> > + u8 gpio_dir;
> > + u8 gpio_int_mask;
> > + u8 gpio_set;
> > + u8 gpio_clr;
> > + u8 gpio_status;
> > +};
> > +
> > +struct xr_port_privte {
> > + const struct xr_uart_regs *regs;
> > + bool port_open;
>
> No lock? As I pointed out before, you're gonna need one to coordinate
> with gpiolib. Better not add the flag until you use it.
>
> > +};
> > +
> > +struct xr_txrx_clk_mask {
> > + u16 tx;
> > + u16 rx0;
> > + u16 rx1;
> > +};
> > +
> > +#define XR21V141X_ID 0x1410
>
> Not used.
>
> > +#define XR_INT_OSC_HZ 48000000U
> > +#define XR21V141X_MIN_SPEED 46U
> > +#define XR21V141X_MAX_SPEED XR_INT_OSC_HZ
> > +
> > +/* USB Requests */
> > +#define XR_SET_XR21V141X 0
> > +#define XR_GET_XR21V141X 1
>
> Stick to one style; either use a device-type specific prefix or suffix
> for the defines.
>
> > +
> > +#define XR21V141X_CLOCK_DIVISOR_0 0x4
> > +#define XR21V141X_CLOCK_DIVISOR_1 0x5
> > +#define XR21V141X_CLOCK_DIVISOR_2 0x6
> > +#define XR21V141X_TX_CLOCK_MASK_0 0x7
> > +#define XR21V141X_TX_CLOCK_MASK_1 0x8
> > +#define XR21V141X_RX_CLOCK_MASK_0 0x9
> > +#define XR21V141X_RX_CLOCK_MASK_1 0xa
>
> Please 0-pad these are they are registers.

You mean adding 0 after 0x?

>
> > +
> > +/* XR21V141X register blocks */
> > +#define XR21V141X_UART_REG_BLOCK 0
> > +#define XR21V141X_UART_MANAGER_REG_BLOCK 4
> > +#define XR21V141X_UART_CUSTOM_BLOCK 0x66
> > +
> > +/* XR21V141X UART Manager Registers */
> > +#define XR21V141X_UART_MANAGER_FIFO_ENABLE_REG 0x10
> > +#define XR21V141X_UART_MANAGER_ENABLE_TX_FIFO 0x1
> > +#define XR21V141X_UART_MANAGER_ENABLE_RX_FIFO 0x2
> > +
> > +#define XR21V141X_UART_MANAGER_RX_FIFO_RESET 0x18
> > +#define XR21V141X_UART_MANAGER_TX_FIFO_RESET 0x1c
>
> s/UART_MANAGER/UM/ should do fine for the register definitions (it was
> just "URM" that was non-obvious).

[...]

> > +
> > +static int xr_set_baudrate(struct tty_struct *tty,
> > + struct usb_serial_port *port)
> > +{
> > + u32 divisor, baud, idx;
> > + u16 tx_mask, rx_mask;
> > + int ret;
> > +
> > + baud = clamp(tty->termios.c_ospeed, XR21V141X_MIN_SPEED,
> > + XR21V141X_MAX_SPEED);
>
> You still need to handle B0, which is a valid request and means that
> DTR/RTS should be deasserted.
>
> > + divisor = XR_INT_OSC_HZ / baud;
> > + idx = (32 * divisor) & 0x1f;
>
> This looks broken as you're throwing away the remainder (cf. datasheet
> 3.3.3 and original implementation).
>

Ah yes. Will fix it.

[...]

> > +
> > +static int xr_tiocmset_port(struct usb_serial_port *port,
> > + unsigned int set, unsigned int clear)
> > +{
> > + struct xr_port_private *port_priv = usb_get_serial_port_data(port);
> > + int ret = 0;
> > + u8 gpio_set = 0;
> > + u8 gpio_clr = 0;
> > +
> > + /* Modem control pins are active low, so set & clr are swapped */
> > + if (set & TIOCM_RTS)
> > + gpio_clr |= UART_MODE_RTS;
> > + if (set & TIOCM_DTR)
> > + gpio_clr |= UART_MODE_DTR;
> > + if (clear & TIOCM_RTS)
> > + gpio_set |= UART_MODE_RTS;
> > + if (clear & TIOCM_DTR)
> > + gpio_set |= UART_MODE_DTR;
> > +
> > + /* Writing '0' to gpio_{set/clr} bits has no effect, so no need to do */
> > + if (gpio_clr) {
> > + ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> > + port_priv->regs->gpio_clr, gpio_clr);
> > + }
> > +
> > + if (gpio_set) {
> > + ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> > + port_priv->regs->gpio_set, gpio_set);
> > + }
> > +
> > + return ret;
> > +}
> > +
> > +static int xr_tiocmset(struct tty_struct *tty,
> > + unsigned int set, unsigned int clear)
> > +{
> > + struct usb_serial_port *port = tty->driver_data;
> > +
> > + return xr_tiocmset_port(port, set, clear);
> > +}
> > +
> > +static int xr_attach(struct usb_serial *serial)
> > +{
> > + /* Do not register tty device for the control interface */
> > + if (serial->interface->cur_altsetting->desc.bInterfaceNumber == 0)
> > + return 1;
>
> Ok, so you went for my first suggestion here instead of explicitly
> claiming the sibling interface.
>
> I still think you should bind to the data interface and then explicitly
> claim the control interface instead, since that better reflects that
> these interfaces are used together (and allows for unbinding through
> sysfs etc).
>

How about something like below?

static int xr_probe(struct usb_serial *serial, const struct usb_device_id *id)
{
struct usb_device *usb_dev = interface_to_usbdev(serial->interface);
struct usb_driver *driver = serial->type->usb_driver;
struct usb_interface *control_interface;

/* Don't bind to control interface */
if (serial->interface->cur_altsetting->desc.bInterfaceNumber == 0)
return -ENODEV;

/* But claim the control interface during data interface probe */
control_interface = usb_ifnum_to_if(usb_dev, 0);
if (usb_driver_claim_interface(driver, control_interface, NULL) != 0)
dev_err(serial->interface->dev, "Can't claim control interface");

return 0;
}

> > +
> > + return 0;
> > +}
> > +
> > +static void xr_dtr_rts(struct usb_serial_port *port, int on)
> > +{
> > + if (on)
> > + xr_tiocmset_port(port, TIOCM_DTR | TIOCM_RTS, 0);
> > + else
> > + xr_tiocmset_port(port, 0, TIOCM_DTR | TIOCM_RTS);
> > +}
> > +
> > +static int xr_tiocmget(struct tty_struct *tty)
> > +{
> > + struct usb_serial_port *port = tty->driver_data;
> > + struct xr_port_private *port_priv = usb_get_serial_port_data(port);
> > + int ret;
> > + u8 status;
> > +
> > + ret = xr_get_reg(port, XR21V141X_UART_REG_BLOCK,
> > + port_priv->regs->gpio_status, &status);
> > + if (ret)
> > + return ret;
> > +
> > + /*
> > + * Modem control pins are active low, so reading '0' means it is active
> > + * and '1' means not active.
> > + */
> > + ret = ((status & UART_MODE_DTR) ? 0 : TIOCM_DTR) |
> > + ((status & UART_MODE_RTS) ? 0 : TIOCM_RTS) |
> > + ((status & UART_MODE_CTS) ? 0 : TIOCM_CTS) |
> > + ((status & UART_MODE_DSR) ? 0 : TIOCM_DSR) |
> > + ((status & UART_MODE_RI) ? 0 : TIOCM_RI) |
> > + ((status & UART_MODE_CD) ? 0 : TIOCM_CD);
> > +
> > + return ret;
> > +}
> > +
> > +static void xr_break_ctl(struct tty_struct *tty, int break_state)
> > +{
> > + struct usb_serial_port *port = tty->driver_data;
> > + struct xr_port_private *port_priv = usb_get_serial_port_data(port);
> > + u8 state;
> > +
> > + if (break_state == 0)
> > + state = UART_BREAK_OFF;
> > + else
> > + state = UART_BREAK_ON;
> > +
> > + dev_dbg(&port->dev, "Turning break %s\n",
> > + state == UART_BREAK_OFF ? "off" : "on");
> > + xr_set_reg(port, XR21V141X_UART_REG_BLOCK, port_priv->regs->tx_break,
> > + state);
> > +}
> > +
> > +static int xr_port_probe(struct usb_serial_port *port)
> > +{
> > + struct xr_port_private *port_priv;
> > +
> > + port_priv = kzalloc(sizeof(*port_priv), GFP_KERNEL);
> > + if (!port_priv)
> > + return -ENOMEM;
> > +
> > + /* XR21V141X specific settings */
> > + port_priv->regs = &xr21v141x_regs;
> > +
> > + usb_set_serial_port_data(port, port_priv);
> > +
> > + return 0;
> > +}
> > +
> > +static int xr_port_remove(struct usb_serial_port *port)
> > +{
> > + struct xr_port_private *port_priv = usb_get_serial_port_data(port);
> > +
> > + kfree(port_priv);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct usb_device_id id_table[] = {
> > + { USB_DEVICE(0x04e2, 0x1410) }, /* XR21V141X */
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(usb, id_table);
> > +
> > +static struct usb_serial_driver xr_device = {
> > + .driver = {
> > + .owner = THIS_MODULE,
> > + .name = "xr_serial",
> > + },
> > + .id_table = id_table,
> > + .num_ports = 1,
> > + .open = xr_open,
> > + .close = xr_close,
> > + .break_ctl = xr_break_ctl,
> > + .set_termios = xr_set_termios,
> > + .tiocmget = xr_tiocmget,
> > + .tiocmset = xr_tiocmset,
> > + .attach = xr_attach,
> > + .port_probe = xr_port_probe,
> > + .port_remove = xr_port_remove,
> > + .dtr_rts = xr_dtr_rts
> > +};
> > +
> > +static struct usb_serial_driver * const serial_drivers[] = {
> > + &xr_device, NULL
> > +};
> > +
> > +module_usb_serial_driver(serial_drivers, id_table);
> > +
> > +MODULE_AUTHOR("Manivannan Sadhasivam <mani@kernel.org>");
> > +MODULE_DESCRIPTION("MaxLinear/Exar USB to Serial driver");
> > +MODULE_LICENSE("GPL");
>
> Johan

\
 
 \ /
  Last update: 2020-07-26 17:50    [W:0.062 / U:1.832 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site