lkml.org 
[lkml]   [2020]   [Jul]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH net-next v6 0/4] net: enetc: remove bootloader dependency
On Thu, Jul 09, 2020 at 11:35:22PM +0200, Michael Walle wrote:
> This is a resend [now a new v6] of the series because the conversion to the
> phylink interface will likely take longer:
> https://lore.kernel.org/netdev/CA+h21hpBodyY8CtNH2ktRdc2FqPi=Fjp94=VVZvzSVbnvnfKVg@mail.gmail.com/
> Also the discussion in the v3 resend doesn't look like it will be resolved
> soon :/
> https://lore.kernel.org/netdev/20200701213433.9217-1-michael@walle.cc/
>
> Unfortunately, we have boards in the wild with a bootloader which doesn't
> set the PCS up correctly. Thus I'd really see this patches picked up as an
> intermediate step until the phylink conversion is ready. Vladimir Oltean
> already offered to convert enetc to phylink when he converts the felix to
> phylink. After this series the PCS setup of the enetc looks almost the same
> as the current felix setup. Thus conversion should be easy.
>
> These patches were picked from the following series:
> https://lore.kernel.org/netdev/1567779344-30965-1-git-send-email-claudiu.manoil@nxp.com/
> They have never been resent. I've picked them up, addressed Andrews
> comments, fixed some more bugs and asked Claudiu if I can keep their SOB
> tags; he agreed. I've tested this on our board which happens to have a
> bootloader which doesn't do the enetc setup in all cases. Though, only
> SGMII mode was tested.
>
> changes since v5:
> - fixed pcs->autoneg_complete and pcs->link assignment. Thanks Vladimir.
>
> changes since v4:
> - moved (and renamed) the USXGMII constants to include/uapi/linux/mdio.h.
> Suggested by Russell King.
>
> changes since v3:
> - rebased to latest net-next where devm_mdiobus_free() was removed.
> replace it by mdiobus_free(). The internal MDIO bus is optional, if
> there is any error, we try to run with the bootloader default PCS
> settings, thus in the error case, we need to free the mdiobus.
>
> changes since v2:
> - removed SOBs from "net: enetc: Initialize SerDes for SGMII and USXGMII
> protocols" because almost everything has changed.
> - get a phy_device for the internal PCS PHY so we can use the phy_
> functions instead of raw mdiobus writes
> - reuse macros already defined in fsl_mdio.h, move missing bits from
> felix to fsl_mdio.h, because they share the same PCS PHY building
> block
> - added 2500BaseX mode (based on felix init routine)
> - changed xgmii mode to usxgmii mode, because it is actually USXGMII and
> felix does the same.
> - fixed devad, which is 0x1f (MMD_VEND2)
>
> changes since v1:
> - mdiobus id is '"imdio-%s", dev_name(dev)' because the plain dev_name()
> is used by the emdio.
> - use mdiobus_write() instead of imdio->write(imdio, ..), since this is
> already a full featured mdiobus
> - set phy_mask to ~0 to avoid scanning the bus
> - use phy_interface_mode_is_rgmii(phy_mode) to also include the RGMII
> modes with pad delays.
> - move enetc_imdio_init() to enetc_pf.c, there shouldn't be any other
> users, should it?
> - renamed serdes to SerDes
> - printing the error code of mdiobus_register() in the error path
> - call mdiobus_unregister() on _remove()
> - call devm_mdiobus_free() if mdiobus_register() fails, since an
> error is not fatal
>
> Alex Marginean (1):
> net: enetc: Use DT protocol information to set up the ports
>
> Michael Walle (3):
> net: phy: add USXGMII link partner ability constants
> net: dsa: felix: (re)use already existing constants
> net: enetc: Initialize SerDes for SGMII and USXGMII protocols
>
> drivers/net/dsa/ocelot/felix_vsc9959.c | 45 ++---
> .../net/ethernet/freescale/enetc/enetc_hw.h | 3 +
> .../net/ethernet/freescale/enetc/enetc_pf.c | 188 +++++++++++++++---
> .../net/ethernet/freescale/enetc/enetc_pf.h | 5 +
> include/uapi/linux/mdio.h | 26 +++
> 5 files changed, 210 insertions(+), 57 deletions(-)
>
> --
> 2.20.1
>

I plan to give this series a go on an LS1028A-QDS later today to make
sure there are no regressions.

Thanks,
-Vladimir

\
 
 \ /
  Last update: 2020-07-11 09:53    [W:0.133 / U:0.244 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site