lkml.org 
[lkml]   [2020]   [Jul]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] PCI: aardvark: Don't touch PCIe registers if no card connected
On Tuesday 30 June 2020 09:58:48 Bjorn Helgaas wrote:
> On Tue, Jun 30, 2020 at 04:04:20PM +0200, Pali Rohár wrote:
> > On Tuesday 30 June 2020 08:51:27 Bjorn Helgaas wrote:
> > > On Thu, May 28, 2020 at 06:38:09PM +0200, Pali Rohár wrote:
> > > > On Thursday 28 May 2020 11:26:04 Bjorn Helgaas wrote:
> > > > > On Thu, May 28, 2020 at 04:31:41PM +0200, Pali Rohár wrote:
> > > > > > When there is no PCIe card connected and advk_pcie_rd_conf() or
> > > > > > advk_pcie_wr_conf() is called for PCI bus which doesn't belong to emulated
> > > > > > root bridge, the aardvark driver throws the following error message:
> > > > > >
> > > > > > advk-pcie d0070000.pcie: config read/write timed out
> > > > > >
> > > > > > Obviously accessing PCIe registers of disconnected card is not possible.
> > > > > >
> > > > > > Extend check in advk_pcie_valid_device() function for validating
> > > > > > availability of PCIe bus. If PCIe link is down, then the device is marked
> > > > > > as Not Found and the driver does not try to access these registers.
> > > > > >
> > > > > > Signed-off-by: Pali Rohár <pali@kernel.org>
> > > > > > ---
> > > > > > drivers/pci/controller/pci-aardvark.c | 3 +++
> > > > > > 1 file changed, 3 insertions(+)
> > > > > >
> > > > > > diff --git a/drivers/pci/controller/pci-aardvark.c b/drivers/pci/controller/pci-aardvark.c
> > > > > > index 90ff291c24f0..53a4cfd7d377 100644
> > > > > > --- a/drivers/pci/controller/pci-aardvark.c
> > > > > > +++ b/drivers/pci/controller/pci-aardvark.c
> > > > > > @@ -644,6 +644,9 @@ static bool advk_pcie_valid_device(struct advk_pcie *pcie, struct pci_bus *bus,
> > > > > > if ((bus->number == pcie->root_bus_nr) && PCI_SLOT(devfn) != 0)
> > > > > > return false;
> > > > > >
> > > > > > + if (bus->number != pcie->root_bus_nr && !advk_pcie_link_up(pcie))
> > > > > > + return false;
> > > > >
> > > > > I don't think this is the right fix. This makes it racy because the
> > > > > link may go down after we call advk_pcie_valid_device() but before we
> > > > > perform the config read.
> > > >
> > > > Yes, it is racy, but I do not think it cause problems. Trying to read
> > > > PCIe registers when device is not connected cause just those timeouts,
> > > > printing error message and increased delay in advk_pcie_wait_pio() due
> > > > to polling loop. This patch reduce unnecessary access to PCIe registers
> > > > when advk_pcie_wait_pio() polling just fail.
> > >
> > > What happens when the device is removed after advk_pcie_link_up()
> > > returns true, but before we actually do the config access?
> >
> > Do you mean to remove device physically at runtime? I was told that our
> > board would crash or issue reset. Removing device from mini PCIe slot
> > without power off is not supported.
>
> Right, I don't think PCIe mini cards support hotplug.
>
> > Anyway, currently we are trying to read from device registers even when
> > no device is connected. So when advk_pcie_link_up() returns true and
> > after that device is not connected (somehow board and kernel would be
> > still alive) I guess that it would behave as without applying this
> > patch. So kernel starts reading from register and would wait until
> > timeout expires. As device is not connected there would be no answer,
> > so kernel print error message to dmesg (same as in commit message) and
> > returns error that read failed.
>
> OK, so if I understand correctly, checking advk_pcie_link_up() is
> strictly an optimization. If we guess wrong (e.g., after calling
> advk_pcie_link_up(), the link went down because the card was removed,
> DPC triggered, etc), the only bad thing is that we wait for a timeout;
> it never causes a crash.

Yes.

> If that's the case, I'm fine with this. But please add a comment to
> that effect.

Ok, I will send V2 with updated commit message.

> I think several other drivers check for the link being up because we
> actually crash if we try to read config space when the link is down.
> That's what I was trying to avoid here.
>
> Bjorn

\
 
 \ /
  Last update: 2020-07-01 10:09    [W:0.058 / U:0.328 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site