lkml.org 
[lkml]   [2020]   [Jun]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 2/2] Add PWM fan controller driver for LGM SoC
From
Date

Hi Uwe,

Thanks for your valuable feedback.

On 19/6/2020 2:02 pm, Uwe Kleine-König wrote:
> Hello Rahul,
>
> On Thu, Jun 18, 2020 at 08:05:13PM +0800, Rahul Tanwar wrote:
>> Intel Lightning Mountain(LGM) SoC contains a PWM fan controller.
>> This PWM controller does not have any other consumer, it is a
>> dedicated PWM controller for fan attached to the system. Add
>> driver for this PWM fan controller.
>>
>> Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
>> ---
>> drivers/pwm/Kconfig | 9 +
>> drivers/pwm/Makefile | 1 +
>> drivers/pwm/pwm-intel-lgm.c | 400 ++++++++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 410 insertions(+)
>> create mode 100644 drivers/pwm/pwm-intel-lgm.c
>>
>> diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
>> index cb8d739067d2..a3303e22d5fa 100644
>> --- a/drivers/pwm/Kconfig
>> +++ b/drivers/pwm/Kconfig
>> @@ -232,6 +232,15 @@ config PWM_IMX_TPM
>> To compile this driver as a module, choose M here: the module
>> will be called pwm-imx-tpm.
>>
>> +config PWM_INTEL_LGM
>> + tristate "Intel LGM PWM support"
>> + depends on X86 || COMPILE_TEST
>> + help
>> + Generic PWM fan controller driver for LGM SoC.
>> +
>> + To compile this driver as a module, choose M here: the module
>> + will be called pwm-intel-lgm.
>> +
>> config PWM_IQS620A
>> tristate "Azoteq IQS620A PWM support"
>> depends on MFD_IQS62X || COMPILE_TEST
>> diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
>> index a59c710e98c7..db154a6b4f51 100644
>> --- a/drivers/pwm/Makefile
>> +++ b/drivers/pwm/Makefile
>> @@ -20,6 +20,7 @@ obj-$(CONFIG_PWM_IMG) += pwm-img.o
>> obj-$(CONFIG_PWM_IMX1) += pwm-imx1.o
>> obj-$(CONFIG_PWM_IMX27) += pwm-imx27.o
>> obj-$(CONFIG_PWM_IMX_TPM) += pwm-imx-tpm.o
>> +obj-$(CONFIG_PWM_INTEL_LGM) += pwm-intel-lgm.o
>> obj-$(CONFIG_PWM_IQS620A) += pwm-iqs620a.o
>> obj-$(CONFIG_PWM_JZ4740) += pwm-jz4740.o
>> obj-$(CONFIG_PWM_LP3943) += pwm-lp3943.o
>> diff --git a/drivers/pwm/pwm-intel-lgm.c b/drivers/pwm/pwm-intel-lgm.c
>> new file mode 100644
>> index 000000000000..3c7077acb161
>> --- /dev/null
>> +++ b/drivers/pwm/pwm-intel-lgm.c
>> @@ -0,0 +1,400 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Copyright (C) 2020 Intel Corporation.
>> + *
>> + * Notes & Limitations:
>> + * - The hardware supports fixed period which is dependent on 2/3 or 4
>> + * wire fan mode.
>> + * - Supports normal polarity. Does not support changing polarity.
>> + * - When PWM is disabled, output of PWM will become 0(inactive). It doesn't
>> + * keep track of running period.
>> + * - When duty cycle is changed, PWM output may be a mix of previous setting
>> + * and new setting for the first period. From second period, the output is
>> + * based on new setting.
>> + * - Supports 100% duty cycle.
>> + * - It is a dedicated PWM fan controller. There are no other consumers for
>> + * this PWM controller.
>> + */
>> +#include <linux/bitfield.h>
>> +#include <linux/clk.h>
>> +#include <linux/module.h>
>> +#include <linux/of_device.h>
>> +#include <linux/pwm.h>
>> +#include <linux/regmap.h>
>> +#include <linux/reset.h>
>> +
>> +#define PWM_FAN_CON0 0x0
>> +#define PWM_FAN_EN_EN BIT(0)
>> +#define PWM_FAN_EN_DIS 0x0
>> +#define PWM_FAN_EN_MSK BIT(0)
>> +#define PWM_FAN_MODE_2WIRE 0x0
>> +#define PWM_FAN_MODE_4WIRE 0x1
>> +#define PWM_FAN_MODE_MSK BIT(1)
>> +#define PWM_FAN_PWM_DIS_DIS 0x0
>> +#define PWM_FAN_PWM_DIS_MSK BIT(2)
>> +#define PWM_TACH_EN_EN 0x1
>> +#define PWM_TACH_EN_MSK BIT(4)
>> +#define PWM_TACH_PLUS_2 0x0
>> +#define PWM_TACH_PLUS_4 0x1
>> +#define PWM_TACH_PLUS_MSK BIT(5)
>> +#define PWM_FAN_DC_MSK GENMASK(23, 16)
>> +
>> +#define PWM_FAN_CON1 0x4
>> +#define PWM_FAN_MAX_RPM_MSK GENMASK(15, 0)
>> +
>> +#define PWM_FAN_STAT 0x10
>> +#define PWM_FAN_TACH_MASK GENMASK(15, 0)
>> +
>> +#define MAX_RPM (BIT(16) - 1)
>> +#define DFAULT_RPM 4000
>> +#define MAX_DUTY_CYCLE (BIT(8) - 1)
>> +
>> +#define FRAC_BITS 10
>> +#define DC_BITS 8
>> +#define TWO_TENTH 204
>> +
>> +#define PERIOD_2WIRE_NSECS 40000000
>> +#define PERIOD_4WIRE_NSECS 40000
>> +
>> +#define TWO_SECONDS 2000
>> +#define IGNORE_FIRST_ERR 1
>> +#define THIRTY_SECS_WINDOW 15
>> +#define ERR_CNT_THRESHOLD 6
>> +
>> +struct lgm_pwm_chip {
>> + struct pwm_chip chip;
>> + struct regmap *regmap;
>> + struct clk *clk;
>> + struct reset_control *rst;
>> + u32 tach_en;
>> + u32 max_rpm;
>> + u32 set_rpm;
>> + u32 set_dc;
>> + u32 period;
>> + struct delayed_work work;
>> +};
>> +
>> +static inline struct lgm_pwm_chip *to_lgm_pwm_chip(struct pwm_chip *chip)
>> +{
>> + return container_of(chip, struct lgm_pwm_chip, chip);
>> +}
>> +
>> +static int lgm_pwm_update_dc(struct lgm_pwm_chip *pc, u32 val)
>> +{
>> + return regmap_update_bits(pc->regmap, PWM_FAN_CON0, PWM_FAN_DC_MSK,
>> + FIELD_PREP(PWM_FAN_DC_MSK, val));
>> +}
>> +
>> +static int lgm_pwm_enable(struct pwm_chip *chip, bool enable)
>> +{
>> + struct lgm_pwm_chip *pc = to_lgm_pwm_chip(chip);
>> + struct regmap *regmap = pc->regmap;
>> +
>> + if (enable) {
>> + regmap_update_bits(regmap, PWM_FAN_CON0,
>> + PWM_FAN_EN_MSK, PWM_FAN_EN_EN);
>> + if (pc->tach_en)
>> + schedule_delayed_work(&pc->work, msecs_to_jiffies(10000));
>> + } else {
>> + if (pc->tach_en)
>> + cancel_delayed_work_sync(&pc->work);
>> + regmap_update_bits(regmap, PWM_FAN_CON0,
>> + PWM_FAN_EN_MSK, PWM_FAN_EN_DIS);
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int lgm_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
>> + const struct pwm_state *state)
>> +{
>> + struct lgm_pwm_chip *pc = to_lgm_pwm_chip(chip);
>> + struct pwm_state cur_state;
>> + u32 duty_cycle, duty, val;
>> + int ret = 0;
>> +
>> + if (state->polarity != PWM_POLARITY_NORMAL ||
>> + state->period != pc->period)
> The period-check is too strict, please accept periods bigger than the
> resulting value. This case however isn't handled correctly yet in the
> following code and needs:
>
> period = min(state->period, pc->period);
>
> if (state->polarity != PWM_POLARITY_NORMAL ||
> period < pc->period)
> return -EINVAL;
>
> (and then use period instead of state->period in the following)
>
>> + return -EINVAL;
>> +
>> + cur_state = pwm->state;
>> + duty_cycle = state->duty_cycle;
> This would then be:
>
> duty_cycle = min(state->duty_cycle, period);
>
>> + if (!state->enabled)
>> + duty_cycle = 0;
> What happens if you don't set duty_cycle to 0? Is it just to prevent a
> spike in lgm_pwm_update_dc before calling lgm_pwm_enable(.., false)? If
> so, what about skipping writing (and calculating) the duty register
> value at all?

Thanks, will update. Agree that setting duty_cycle to 0 is redundant.
Setting duty_cycle to 0 is equivalent to disabling PWM. Will remove it.

>> + duty = duty_cycle * (1U << DC_BITS);
>> + val = DIV_ROUND_CLOSEST(duty, state->period);
> This is equivalent to:
>
> val = DIV_ROUND_CLOSEST(duty_cycle << DC_BITS, state->period);
>
> which doesn't need two variables with similar name but different
> scaling. Having said that using closest rounding is wrong here, please
> round down.

Unable to find a 32 bit variant of DIV_ROUND_DOWN API unlike
DIV_ROUND_UP. Do you have any suggestion for such a API? If not,
i will add one new API for this purpose in the driver.

>> + val = min_t(u32, val, MAX_DUTY_CYCLE);
> Hmm, this looks suspicious. Does the hardware really produce 100% when
> val = MAX_DUTY_CYCLE? Either it doesn't or there is a rounding error in
> your algorithm. Does the PWM support 0%? It would help to mention the
> formula from the reference manual to verify and understand your
> algorithm. Please add a comment for that.

Yes, hardware claims to produce 100% when val = 0xff for 8 bit duty cycle
register field. But it doesn't support 0%. Minimum supported is 20%.
Sorry i am unable to figure out your point here. Can you please elaborate
more? I was just trying to ensure that reg value doesn't exceed max value
of 0xff.

>> + if (pc->tach_en) {
>> + pc->set_dc = val;
>> + pc->set_rpm = val * pc->max_rpm / MAX_DUTY_CYCLE;
>> + }
>> +
>> + ret = lgm_pwm_update_dc(pc, val);
>> +
>> + if (state->enabled != cur_state.enabled)
>> + lgm_pwm_enable(chip, state->enabled);
> I would prefer if you would make this call conditional on the (cached)
> state of the PWM_FAN_EN_MSK bit instead of pwm->state. This way the
> driver is more independent from pwm API internals.

Well noted.

>> + return ret;
>> +}
>> +
>> +static void lgm_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
>> + struct pwm_state *state)
>> +{
>> + struct lgm_pwm_chip *pc = to_lgm_pwm_chip(chip);
>> + u32 duty, val;
>> +
>> + state->enabled = regmap_test_bits(pc->regmap, PWM_FAN_CON0,
>> + PWM_FAN_EN_EN);
>> + state->polarity = PWM_POLARITY_NORMAL;
>> + state->period = pc->period; /* fixed period */
>> +
>> + regmap_read(pc->regmap, PWM_FAN_CON0, &val);
>> + duty = FIELD_GET(PWM_FAN_DC_MSK, val);
>> + state->duty_cycle = duty * pc->period >> DC_BITS;
> The rounding here must use the inverse rounding of .apply(). So please
> round up here.

Well noted.

>> +}
>> +
>> +static const struct pwm_ops lgm_pwm_ops = {
>> + .get_state = lgm_pwm_get_state,
>> + .apply = lgm_pwm_apply,
>> + .owner = THIS_MODULE,
>> +};
>> +
>> +static void lgm_pwm_tach_work(struct work_struct *work)
>> +{
>> + struct lgm_pwm_chip *pc = container_of(work, struct lgm_pwm_chip,
>> + work.work);
>> + struct regmap *regmap = pc->regmap;
>> + u32 fan_tach, fan_dc, val;
>> + s32 diff;
>> + static u32 fanspeed_err_cnt, time_window, delta_dc;
>> +
>> + /*
>> + * Fan speed is tracked by reading the active duty cycle of PWM output
>> + * from the active duty cycle register. Some variance in the duty cycle
>> + * register value is expected. So we set a time window of 30 seconds and
>> + * if we detect inaccurate fan speed 6 times within 30 seconds then we
>> + * mark it as fan speed problem and fix it by readjusting the duty cycle.
>> + */
>> +
>> + if (fanspeed_err_cnt > IGNORE_FIRST_ERR)
>> + /*
>> + * Ignore first time we detect inaccurate fan speed
>> + * because it is expected during bootup.
>> + */
>> + time_window++;
>> +
>> + if (time_window == THIRTY_SECS_WINDOW) {
>> + /*
>> + * This work is scheduled every 2 seconds i.e. each time_window
>> + * counter step roughly mean 2 seconds. When the time window
>> + * reaches 30 seconds, reset all the counters/logic.
>> + */
>> + fanspeed_err_cnt = 0;
>> + delta_dc = 0;
>> + time_window = 0;
>> + }
>> +
>> + regmap_read(regmap, PWM_FAN_STAT, &fan_tach);
>> + fan_tach &= PWM_FAN_TACH_MASK;
>> + if (!fan_tach)
>> + goto restart_work;
>> +
>> + val = DIV_ROUND_CLOSEST(pc->set_rpm << FRAC_BITS, fan_tach);
>> + diff = val - BIT(FRAC_BITS);
>> +
>> + if (abs(diff) > TWO_TENTH) {
>> + /* if duty cycle diff is more than two tenth, detect it as error */
>> + if (fanspeed_err_cnt > IGNORE_FIRST_ERR)
>> + delta_dc += val;
>> + fanspeed_err_cnt++;
>> + }
>> +
>> + if (fanspeed_err_cnt == ERR_CNT_THRESHOLD) {
>> + /*
>> + * We detected fan speed errors 6 times with 30 seconds.
>> + * Fix the error by readjusting duty cycle and reset
>> + * our counters/logic.
>> + */
>> + fan_dc = pc->set_dc * delta_dc >> (FRAC_BITS + 2);
>> + fan_dc = min_t(u32, fan_dc, MAX_DUTY_CYCLE);
>> + lgm_pwm_update_dc(pc, fan_dc);
>> + fanspeed_err_cnt = 0;
>> + delta_dc = 0;
>> + time_window = 0;
>> + }
>> +
>> +restart_work:
>> + /*
>> + * Fan speed doesn't need continous tracking. Schedule this work
>> + * every two seconds so it doesn't steal too much cpu cycles.
>> + */
>> + schedule_delayed_work(&pc->work, msecs_to_jiffies(TWO_SECONDS));
> You had concerns about my review feedback that I don't like the fan
> stuff in the PWM driver. I still think that the fan part doesn't belong
> here.

We have decided to remove this fan calibration task after concluding that
the same can be achieved by a user space application using sysfs. Will remove
it in v3.

>> +}
>> +
>> +static void lgm_pwm_init(struct lgm_pwm_chip *pc)
>> +{
>> + struct device *dev = pc->chip.dev;
>> + struct regmap *regmap = pc->regmap;
>> + u32 max_rpm, fan_wire, tach_plus, con0_val, con0_mask;
>> +
>> + if (device_property_read_u32(dev, "intel,fan-wire", &fan_wire))
>> + fan_wire = 2; /* default is 2 wire mode */
>> +
>> + con0_val = FIELD_PREP(PWM_FAN_PWM_DIS_MSK, PWM_FAN_PWM_DIS_DIS);
>> + con0_mask = PWM_FAN_PWM_DIS_MSK | PWM_FAN_MODE_MSK;
> Please don't disable the PWM in .probe()

Well noted.

>> +
>> + switch (fan_wire) {
>> + case 4:
>> + con0_val |= FIELD_PREP(PWM_FAN_MODE_MSK, PWM_FAN_MODE_4WIRE) |
>> + FIELD_PREP(PWM_TACH_EN_MSK, PWM_TACH_EN_EN);
>> + con0_mask |= PWM_TACH_EN_MSK | PWM_TACH_PLUS_MSK;
>> + pc->tach_en = 1;
>> + pc->period = PERIOD_4WIRE_NSECS;
>> + break;
>> + default:
>> + /* default is 2wire mode */
>> + con0_val |= FIELD_PREP(PWM_FAN_MODE_MSK, PWM_FAN_MODE_2WIRE);
>> + pc->period = PERIOD_2WIRE_NSECS;
>> + break;
>> + }
>> +
>> + if (pc->tach_en) {
>> + if (device_property_read_u32(dev, "intel,tach-plus",
>> + &tach_plus))
>> + tach_plus = 2;
>> +
>> + switch (tach_plus) {
>> + case 4:
>> + con0_val |= FIELD_PREP(PWM_TACH_PLUS_MSK,
>> + PWM_TACH_PLUS_4);
>> + break;
>> + default:
>> + con0_val |= FIELD_PREP(PWM_TACH_PLUS_MSK,
>> + PWM_TACH_PLUS_2);
>> + break;
>> + }
>> +
>> + if (device_property_read_u32(dev, "intel,max-rpm", &max_rpm))
>> + max_rpm = DFAULT_RPM;
>> +
>> + max_rpm = min_t(u32, max_rpm, MAX_RPM);
>> + if (max_rpm == 0)
>> + max_rpm = DFAULT_RPM;
>> +
>> + pc->max_rpm = max_rpm;
>> + INIT_DEFERRABLE_WORK(&pc->work, lgm_pwm_tach_work);
>> + regmap_update_bits(regmap, PWM_FAN_CON1,
>> + PWM_FAN_MAX_RPM_MSK, max_rpm);
>> + }
>> +
>> + regmap_update_bits(regmap, PWM_FAN_CON0, con0_mask, con0_val);
>> +}
>> +
>> +static const struct regmap_config pwm_regmap_config = {
> Here you missed to add the lgm_ prefix.
>
>> + .reg_bits = 32,
>> + .reg_stride = 4,
>> + .val_bits = 32,
>> +};
>> +
>> +static int lgm_pwm_probe(struct platform_device *pdev)
>> +{
>> + struct lgm_pwm_chip *pc;
>> + struct device *dev = &pdev->dev;
>> + void __iomem *io_base;
>> + int ret;
>> +
>> + pc = devm_kzalloc(dev, sizeof(*pc), GFP_KERNEL);
>> + if (!pc)
>> + return -ENOMEM;
>> +
>> + io_base = devm_platform_ioremap_resource(pdev, 0);
>> + if (IS_ERR(io_base))
>> + return PTR_ERR(io_base);
>> +
>> + pc->regmap = devm_regmap_init_mmio(dev, io_base, &pwm_regmap_config);
>> + if (IS_ERR(pc->regmap)) {
>> + ret = PTR_ERR(pc->regmap);
>> + dev_err(dev, "failed to init register map: %pe\n", pc->regmap);
>> + return ret;
>> + }
>> +
>> + pc->clk = devm_clk_get(dev, NULL);
>> + if (IS_ERR(pc->clk)) {
>> + ret = PTR_ERR(pc->clk);
>> + dev_err(dev, "failed to get clock: %pe\n", pc->clk);
>> + return ret;
>> + }
>> +
>> + pc->rst = devm_reset_control_get(dev, NULL);
>> + if (IS_ERR(pc->rst)) {
>> + ret = PTR_ERR(pc->rst);
>> + dev_err(dev, "failed to get reset control: %pe\n", pc->rst);
>> + return ret;
>> + }
>> +
>> + ret = reset_control_deassert(pc->rst);
>> + if (ret) {
>> + dev_err(dev, "cannot deassert reset control: %pe\n",
>> + ERR_PTR(ret));
>> + return ret;
>> + }
>> +
>> + ret = clk_prepare_enable(pc->clk);
>> + if (ret) {
>> + dev_err(dev, "failed to enable clock\n");
>> + return ret;
>> + }
>> +
>> + pc->chip.dev = dev;
>> + pc->chip.ops = &lgm_pwm_ops;
>> + pc->chip.npwm = 1;
>> +
>> + lgm_pwm_init(pc);
>> +
>> + ret = pwmchip_add(&pc->chip);
>> + if (ret < 0) {
>> + dev_err(dev, "failed to add PWM chip: %d\n", ret);
> %pe please.

Well noted. Thanks.

Regards,
Rahul

\
 
 \ /
  Last update: 2020-06-25 09:29    [W:0.158 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site