lkml.org 
[lkml]   [2020]   [Jun]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH] soc: qcom: rpmh: Remove serialization of TCS commands
Hi,

On Fri, May 29, 2020 at 3:52 AM Maulik Shah <mkshah@codeaurora.org> wrote:
>
> From: Lina Iyer <ilina@codeaurora.org>
>
> Requests sent to RPMH can be sent as fire-n-forget or response required,
> with the latter ensuring the command has been completed by the hardware
> accelerator. Commands in a request with tcs_cmd::wait set, would ensure
> that those select commands are sent as response required, even though
> the actual TCS request may be fire-n-forget.
>
> Also, commands with .wait flag were also guaranteed to be complete
> before the following command in the TCS is sent. This means that the
> next command of the same request blocked until the current request is
> completed. This could mean waiting for a voltage to settle or series of
> NOCs be configured before the next command is sent. But drivers using
> this feature have never cared about the serialization aspect. By not
> enforcing the serialization we can allow the hardware to run in parallel
> improving the performance.
>
> Let's clarify the usage of this member in the tcs_cmd structure to mean
> only completion and not serialization. This should also improve the
> performance of bus requests where changes could happen in parallel.
> Also, CPU resume from deep idle may see benefits from certain wake
> requests.
>
> Signed-off-by: Lina Iyer <ilina@codeaurora.org>

You are posting the patch and so you need your SoB too.


> ---
> drivers/soc/qcom/rpmh-rsc.c | 19 ++++++++-----------
> include/soc/qcom/tcs.h | 5 +++--
> 2 files changed, 11 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/soc/qcom/rpmh-rsc.c b/drivers/soc/qcom/rpmh-rsc.c
> index 076fd27..d99e639 100644
> --- a/drivers/soc/qcom/rpmh-rsc.c
> +++ b/drivers/soc/qcom/rpmh-rsc.c
> @@ -413,8 +413,7 @@ static irqreturn_t tcs_tx_done(int irq, void *p)
> cmd = &req->cmds[j];
> sts = read_tcs_cmd(drv, RSC_DRV_CMD_STATUS, i, j);
> if (!(sts & CMD_STATUS_ISSUED) ||
> - ((req->wait_for_compl || cmd->wait) &&
> - !(sts & CMD_STATUS_COMPL))) {
> + (cmd->wait && !(sts & CMD_STATUS_COMPL))) {

I don't quite understand this part of the change. Why don't you need
to check "req->wait_for_compl" anymore? You are still setting
"CMD_MSGID_RESP_REQ" if "req->wait_for_compl" is set and none of the
code in your patch actually sets "cmd->wait" (unlike what's implied in
your change to the header file). Maybe some previous version of the
patch _was_ actually setting "cmd->wait" and when you stopped doing
that you forgot to restore this part of the change?


> pr_err("Incomplete request: %s: addr=%#x data=%#x",
> drv->name, cmd->addr, cmd->data);
> err = -EIO;
> @@ -433,7 +432,6 @@ static irqreturn_t tcs_tx_done(int irq, void *p)
> skip:
> /* Reclaim the TCS */
> write_tcs_reg(drv, RSC_DRV_CMD_ENABLE, i, 0);
> - write_tcs_reg(drv, RSC_DRV_CMD_WAIT_FOR_CMPL, i, 0);

Should you also be removing the write to RSC_DRV_CMD_WAIT_FOR_CMPL in
both tcs_write() and tcs_invalidate()? Those are the only two places
left that set this register and they both always set it to 0.


> writel_relaxed(BIT(i), drv->tcs_base + RSC_DRV_IRQ_CLEAR);
> spin_lock(&drv->lock);
> clear_bit(i, drv->tcs_in_use);
> @@ -465,23 +463,23 @@ static irqreturn_t tcs_tx_done(int irq, void *p)
> static void __tcs_buffer_write(struct rsc_drv *drv, int tcs_id, int cmd_id,
> const struct tcs_request *msg)
> {
> - u32 msgid, cmd_msgid;
> + u32 msgid;
> + u32 cmd_msgid = CMD_MSGID_LEN | CMD_MSGID_WRITE;
> u32 cmd_enable = 0;
> - u32 cmd_complete;
> struct tcs_cmd *cmd;
> int i, j;
>
> - cmd_msgid = CMD_MSGID_LEN;
> + /* Convert all commands to RR when the request has wait_for_compl set */
> cmd_msgid |= msg->wait_for_compl ? CMD_MSGID_RESP_REQ : 0;
> - cmd_msgid |= CMD_MSGID_WRITE;
> -
> - cmd_complete = read_tcs_reg(drv, RSC_DRV_CMD_WAIT_FOR_CMPL, tcs_id);
>
> for (i = 0, j = cmd_id; i < msg->num_cmds; i++, j++) {
> cmd = &msg->cmds[i];
> cmd_enable |= BIT(j);
> - cmd_complete |= cmd->wait << j;
> msgid = cmd_msgid;
> + /*
> + * Additionally, if the cmd->wait is set, make the command
> + * response reqd even if the overall request was fire-n-forget.
> + */
> msgid |= cmd->wait ? CMD_MSGID_RESP_REQ : 0;
>
> write_tcs_cmd(drv, RSC_DRV_CMD_MSGID, tcs_id, j, msgid);
> @@ -490,7 +488,6 @@ static void __tcs_buffer_write(struct rsc_drv *drv, int tcs_id, int cmd_id,
> trace_rpmh_send_msg_rcuidle(drv, tcs_id, j, msgid, cmd);
> }
>
> - write_tcs_reg(drv, RSC_DRV_CMD_WAIT_FOR_CMPL, tcs_id, cmd_complete);
> cmd_enable |= read_tcs_reg(drv, RSC_DRV_CMD_ENABLE, tcs_id);
> write_tcs_reg(drv, RSC_DRV_CMD_ENABLE, tcs_id, cmd_enable);
> }
> diff --git a/include/soc/qcom/tcs.h b/include/soc/qcom/tcs.h
> index 7a2a055..d1c87fd 100644
> --- a/include/soc/qcom/tcs.h
> +++ b/include/soc/qcom/tcs.h
> @@ -1,6 +1,6 @@
> /* SPDX-License-Identifier: GPL-2.0 */
> /*
> - * Copyright (c) 2016-2019, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2016-2020, The Linux Foundation. All rights reserved.
> */
>
> #ifndef __SOC_QCOM_TCS_H__
> @@ -30,7 +30,7 @@ enum rpmh_state {
> *
> * @addr: the address of the resource slv_id:18:16 | offset:0:15
> * @data: the resource state request
> - * @wait: wait for this request to be complete before sending the next
> + * @wait: Ensure that this command is complete before returning

I have a hard time understanding what you're trying to convey here.
Do we even need the "wait" in this structure?

When you call rpmh_write() we use DEFINE_RPMH_MSG_ONSTACK which sets
"wait_for_compl", right?

...so I guess you're expecting this to be used for rpmh_write_async()?
...but we never wait in that case, do we?

...or are you expecting rpmh_write_batch() to take advantage of this somehow?


> */
> struct tcs_cmd {
> u32 addr;
> @@ -43,6 +43,7 @@ struct tcs_cmd {
> *
> * @state: state for the request.
> * @wait_for_compl: wait until we get a response from the h/w accelerator
> + * (sets the cmd->wait for all commmands in the request)

s/commmands/scommands

Also: I don't think this actually goes and modifies "cmd->wait" for
all the commands in the request, does it? Maybe say "same as setting
cmd->wait for all the commands in the request"?


-Doug

\
 
 \ /
  Last update: 2020-06-19 06:29    [W:0.212 / U:0.388 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site