lkml.org 
[lkml]   [2020]   [May]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] drm/bridge: ti-sn65dsi86: Implement lane reordering + polarity
From
Date
Quoting Douglas Anderson (2020-05-04 21:36:31)
> The ti-sn65dsi86 MIPI DSI to eDP bridge chip supports arbitrary
> remapping of eDP lanes and also polarity inversion. Both of these
> features have been described in the device tree bindings for the
> device since the beginning but were never implemented in the driver.
> Implement both of them.
>
> Part of this change also allows you to (via the same device tree
> bindings) specify to use fewer than the max number of DP lanes that
> the panel reports. This could be useful if your display supports more
> lanes but only a few are hooked up on your board.
>
> Signed-off-by: Douglas Anderson <dianders@chromium.org>
> ---

Except for one thing below:

Reviewed-by: Stephen Boyd <swboyd@chromium.org>

> diff --git a/drivers/gpu/drm/bridge/ti-sn65dsi86.c b/drivers/gpu/drm/bridge/ti-sn65dsi86.c
> index 1a125423eb07..52cca54b525f 100644
> --- a/drivers/gpu/drm/bridge/ti-sn65dsi86.c
> +++ b/drivers/gpu/drm/bridge/ti-sn65dsi86.c
> @@ -707,26 +716,20 @@ static void ti_sn_bridge_enable(struct drm_bridge *bridge)
> int dp_rate_idx;
> unsigned int val;
> int ret = -EINVAL;
> + int max_dp_lanes;
>
> - /*
> - * Run with the maximum number of lanes that the DP sink supports.
> - *
> - * Depending use cases, we might want to revisit this later because:
> - * - It's plausible that someone may have run fewer lines to the
> - * sink than the sink actually supports, assuming that the lines
> - * will just be driven at a higher rate.
> - * - The DP spec seems to indicate that it's more important to minimize
> - * the number of lanes than the link rate.
> - *
> - * If we do revisit, it would be important to measure the power impact.
> - */
> - pdata->dp_lanes = ti_sn_get_max_lanes(pdata);
> + max_dp_lanes = ti_sn_get_max_lanes(pdata);
> + pdata->dp_lanes = min(pdata->dp_lanes, max_dp_lanes);
>
> /* DSI_A lane config */
> val = CHA_DSI_LANES(4 - pdata->dsi->lanes);

Not a problem in this patch, but maybe this can be SN_MAX_DP_LANES -
pdata->dsi->lanes now.

> regmap_update_bits(pdata->regmap, SN_DSI_LANES_REG,
> CHA_DSI_LANES_MASK, val);
>
> + regmap_write(pdata->regmap, SN_LN_ASSIGN_REG, pdata->ln_assign);
> + regmap_update_bits(pdata->regmap, SN_ENH_FRAME_REG, LN_POLRS_MASK,
> + pdata->ln_polrs << LN_POLRS_OFFSET);
> +
> /* set dsi clk frequency value */
> ti_sn_bridge_set_dsi_rate(pdata);
>
> @@ -1063,6 +1066,50 @@ static int ti_sn_setup_gpio_controller(struct ti_sn_bridge *pdata)
> return ret;
> }
>
> +static void ti_sn_bridge_parse_lanes(struct ti_sn_bridge *pdata,
> + struct device_node *np)
> +{
> + u32 lane_assignments[SN_MAX_DP_LANES] = { 0, 1, 2, 3 };
> + u32 lane_polarities[SN_MAX_DP_LANES] = { };
> + struct device_node *endpoint;
> + u8 ln_assign = 0;
> + u8 ln_polrs = 0;

Do we need to assign to 0 to start? Seems like no?

> + int dp_lanes;
> + int i;
> +
> + /*
> + * Read config from the device tree about lane remapping and lane
> + * polarities. These are optional and we assume identity map and
> + * normal polarity if nothing is specified. It's OK to specify just
> + * data-lanes but not lane-polarities but not vice versa.
> + */
> + endpoint = of_graph_get_endpoint_by_regs(np, 1, -1);
> + dp_lanes = of_property_count_u32_elems(endpoint, "data-lanes");
> + if (dp_lanes > 0) {
> + of_property_read_u32_array(endpoint, "data-lanes",
> + lane_assignments, dp_lanes);
> + of_property_read_u32_array(endpoint, "lane-polarities",
> + lane_polarities, dp_lanes);
> + } else {
> + dp_lanes = SN_MAX_DP_LANES;
> + }

Needs an of_node_put(endpoint) here for the
of_graph_get_endpoint_by_regs() above.

> +
> + /*
> + * Convert into register format. Loop over all lanes even if
> + * data-lanes had fewer elements so that we nicely initialize
> + * the LN_ASSIGN register.
> + */
> + for (i = SN_MAX_DP_LANES - 1; i >= 0; i--) {
> + ln_assign = ln_assign << LN_ASSIGN_WIDTH | lane_assignments[i];
> + ln_polrs = ln_polrs << 1 | lane_polarities[i];
> + }
> +
> + /* Stash in our struct for when we power on */
> + pdata->dp_lanes = dp_lanes;
> + pdata->ln_assign = ln_assign;
> + pdata->ln_polrs = ln_polrs;
> +}

\
 
 \ /
  Last update: 2020-05-05 07:44    [W:0.063 / U:0.844 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site