lkml.org 
[lkml]   [2020]   [May]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
SubjectRe: [PATCH 1/2] drivers: thermal: tsens: Add 0C (zeorC) interrupt support
Hi Manaf,

Typo: fix zeorC in subject line.

Please rebase this patch[1] on top of my patch merging tsens-common.c
and tsens.c.

[1] https://lore.kernel.org/linux-arm-msm/e30e2ba6fa5c007983afd4d7d4e0311c0b57917a.1588183879.git.amit.kucheria@linaro.org/

On Tue, May 5, 2020 at 4:42 PM Manaf Meethalavalappu Pallikunhi
<manafm@codeaurora.org> wrote:
>
> TSENS IP v2.6+ adds 0C interrupt support. It triggers set
> interrupt when aggregated minimum temperature of all TSENS falls
> below 0C preset threshold and triggers reset interrupt when aggregate
> minimum temperature of all TSENS crosses above reset threshold.
> Add support for this interrupt in the driver.
>
> It adds another sensor to the of-thermal along with all individual
> TSENS. It enables to add any mitigation for 0C interrupt.
>
> Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org>
> ---
> drivers/thermal/qcom/tsens-common.c | 72 ++++++++++++++++++++++++++++-
> drivers/thermal/qcom/tsens-v2.c | 7 +++
> drivers/thermal/qcom/tsens.c | 51 ++++++++++++++++++--
> drivers/thermal/qcom/tsens.h | 11 +++++
> 4 files changed, 135 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> index 172545366636..44e7edeb9a90 100644
> --- a/drivers/thermal/qcom/tsens-common.c
> +++ b/drivers/thermal/qcom/tsens-common.c
> @@ -198,7 +198,8 @@ static void tsens_set_interrupt_v1(struct tsens_priv *priv, u32 hw_id,
> index = LOW_INT_CLEAR_0 + hw_id;
> break;
> case CRITICAL:
> - /* No critical interrupts before v2 */
> + case ZEROC:
> + /* No critical and 0c interrupts before v2 */
> return;
> }
> regmap_field_write(priv->rf[index], enable ? 0 : 1);
> @@ -229,6 +230,9 @@ static void tsens_set_interrupt_v2(struct tsens_priv *priv, u32 hw_id,
> index_mask = CRIT_INT_MASK_0 + hw_id;
> index_clear = CRIT_INT_CLEAR_0 + hw_id;
> break;
> + case ZEROC:
> + /* Nothing to handle for 0c interrupt */
> + return;
> }
>
> if (enable) {
> @@ -360,6 +364,34 @@ static inline u32 masked_irq(u32 hw_id, u32 mask, enum tsens_ver ver)
> return 0;
> }
>
> +/**
> + * tsens_0c_irq_thread - Threaded interrupt handler for 0c interrupt

Let's use zeroc instead of 0c in the function and variable names and
comments everywhere. Easier to grep and better consistency too.

> + * @irq: irq number
> + * @data: tsens controller private data
> + *
> + * Whenever interrupt triggers notify thermal framework using
> + * thermal_zone_device_update() to update cold temperature mitigation.

How is this mitigation updated?

> + *
> + * Return: IRQ_HANDLED
> + */
> +irqreturn_t tsens_0c_irq_thread(int irq, void *data)
> +{
> + struct tsens_priv *priv = data;
> + struct tsens_sensor *s = &priv->sensor[priv->num_sensors];
> + int temp, ret;
> +
> + ret = regmap_field_read(priv->rf[TSENS_0C_STATUS], &temp);
> + if (ret)
> + return ret;
> +
> + dev_dbg(priv->dev, "[%u] %s: 0c interrupt is %s\n",
> + s->hw_id, __func__, temp ? "triggered" : "cleared");

So triggered is printed for non-zero (including negative) values?

> +
> + thermal_zone_device_update(s->tzd, THERMAL_EVENT_UNSPECIFIED);
> +
> + return IRQ_HANDLED;
> +}
> +
> /**
> * tsens_critical_irq_thread() - Threaded handler for critical interrupts
> * @irq: irq number
> @@ -566,6 +598,20 @@ void tsens_disable_irq(struct tsens_priv *priv)
> regmap_field_write(priv->rf[INT_EN], 0);
> }
>
> +int tsens_get_0c_int_status(const struct tsens_sensor *s, int *temp)
> +{
> + struct tsens_priv *priv = s->priv;
> + int last_temp = 0, ret;
> +
> + ret = regmap_field_read(priv->rf[TSENS_0C_STATUS], &last_temp);
> + if (ret)
> + return ret;
> +
> + *temp = last_temp;
> +
> + return 0;
> +}
> +
> int get_temp_tsens_valid(const struct tsens_sensor *s, int *temp)
> {
> struct tsens_priv *priv = s->priv;
> @@ -833,6 +879,30 @@ int __init init_common(struct tsens_priv *priv)
> regmap_field_write(priv->rf[CC_MON_MASK], 1);
> }
>
> + if (tsens_version(priv) > VER_1_X && ver_minor > 5) {
> + /* 0C interrupt is present only on v2.6+ */
> + priv->rf[TSENS_0C_INT_EN] = devm_regmap_field_alloc(dev,
> + priv->srot_map,
> + priv->fields[TSENS_0C_INT_EN]);
> + if (IS_ERR(priv->rf[TSENS_0C_INT_EN])) {
> + ret = PTR_ERR(priv->rf[TSENS_0C_INT_EN]);
> + goto err_put_device;
> + }
> +
> + /* Check whether 0C interrupt is enabled or not */
> + regmap_field_read(priv->rf[TSENS_0C_INT_EN], &enabled);
> + if (enabled) {
> + priv->feat->zero_c_int = 1;

This should be done at the beginning of the block where you check our
version is > 2.6 since the flag only says whether the feature is
present.

> + priv->rf[TSENS_0C_STATUS] = devm_regmap_field_alloc(dev,
> + priv->tm_map,
> + priv->fields[TSENS_0C_STATUS]);
> + if (IS_ERR(priv->rf[TSENS_0C_STATUS])) {
> + ret = PTR_ERR(priv->rf[TSENS_0C_STATUS]);
> + goto err_put_device;
> + }
> + }
> + }
> +
> spin_lock_init(&priv->ul_lock);
> tsens_enable_irq(priv);
> tsens_debug_init(op);
> diff --git a/drivers/thermal/qcom/tsens-v2.c b/drivers/thermal/qcom/tsens-v2.c
> index b293ed32174b..ce80d82c7255 100644
> --- a/drivers/thermal/qcom/tsens-v2.c
> +++ b/drivers/thermal/qcom/tsens-v2.c
> @@ -11,6 +11,7 @@
> /* ----- SROT ------ */
> #define SROT_HW_VER_OFF 0x0000
> #define SROT_CTRL_OFF 0x0004
> +#define SROT_OC_CTRL_OFF 0x0018
>
> /* ----- TM ------ */
> #define TM_INT_EN_OFF 0x0004
> @@ -23,6 +24,7 @@
> #define TM_Sn_UPPER_LOWER_THRESHOLD_OFF 0x0020
> #define TM_Sn_CRITICAL_THRESHOLD_OFF 0x0060
> #define TM_Sn_STATUS_OFF 0x00a0
> +#define TM_0C_INT_STATUS_OFF 0x00e0
> #define TM_TRDY_OFF 0x00e4
> #define TM_WDOG_LOG_OFF 0x013c
>
> @@ -45,6 +47,7 @@ static const struct reg_field tsens_v2_regfields[MAX_REGFIELDS] = {
> /* CTRL_OFF */
> [TSENS_EN] = REG_FIELD(SROT_CTRL_OFF, 0, 0),
> [TSENS_SW_RST] = REG_FIELD(SROT_CTRL_OFF, 1, 1),
> + [TSENS_0C_INT_EN] = REG_FIELD(SROT_OC_CTRL_OFF, 0, 0),
>
> /* ----- TM ------ */
> /* INTERRUPT ENABLE */
> @@ -86,6 +89,9 @@ static const struct reg_field tsens_v2_regfields[MAX_REGFIELDS] = {
> REG_FIELD_FOR_EACH_SENSOR16(CRITICAL_STATUS, TM_Sn_STATUS_OFF, 19, 19),
> REG_FIELD_FOR_EACH_SENSOR16(MAX_STATUS, TM_Sn_STATUS_OFF, 20, 20),
>
> + /* 0C INETRRUPT STATUS */

Typo: Interrupt

> + [TSENS_0C_STATUS] = REG_FIELD(TM_0C_INT_STATUS_OFF, 0, 0),
> +
> /* TRDY: 1=ready, 0=in progress */
> [TRDY] = REG_FIELD(TM_TRDY_OFF, 0, 0),
> };
> @@ -93,6 +99,7 @@ static const struct reg_field tsens_v2_regfields[MAX_REGFIELDS] = {
> static const struct tsens_ops ops_generic_v2 = {
> .init = init_common,
> .get_temp = get_temp_tsens_valid,
> + .get_0c_status = tsens_get_0c_int_status,
> };
>
> struct tsens_plat_data data_tsens_v2 = {
> diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
> index 2f77d235cf73..e60870c53383 100644
> --- a/drivers/thermal/qcom/tsens.c
> +++ b/drivers/thermal/qcom/tsens.c
> @@ -14,6 +14,17 @@
> #include <linux/thermal.h>
> #include "tsens.h"
>
> +static int tsens_0c_get_temp(void *data, int *temp)
> +{
> + struct tsens_sensor *s = data;
> + struct tsens_priv *priv = s->priv;
> +
> + if (priv->ops->get_0c_status)
> + return priv->ops->get_0c_status(s, temp);
> +
> + return -ENOTSUPP;
> +}
> +
> static int tsens_get_temp(void *data, int *temp)
> {
> struct tsens_sensor *s = data;
> @@ -85,6 +96,10 @@ static const struct thermal_zone_of_device_ops tsens_of_ops = {
> .set_trips = tsens_set_trips,
> };
>
> +static const struct thermal_zone_of_device_ops tsens_0c_of_ops = {
> + .get_temp = tsens_0c_get_temp,
> +};
> +
> static int tsens_register_irq(struct tsens_priv *priv, char *irqname,
> irq_handler_t thread_fn)
> {
> @@ -142,6 +157,21 @@ static int tsens_register(struct tsens_priv *priv)
> ret = tsens_register_irq(priv, "critical",
> tsens_critical_irq_thread);
>
> + if (priv->feat->zero_c_int) {
> + priv->sensor[priv->num_sensors].priv = priv;
> + tzd = devm_thermal_zone_of_sensor_register(priv->dev,
> + priv->sensor[priv->num_sensors].hw_id,
> + &priv->sensor[priv->num_sensors],
> + &tsens_0c_of_ops);
> + if (IS_ERR(tzd)) {
> + ret = 0;
> + return ret;
> + }
> +
> + priv->sensor[priv->num_sensors].tzd = tzd;

Why can't this happen in the previous loop, but increase the loop to
<= num_sensors? It is duplicated code.

> + ret = tsens_register_irq(priv, "zeroc", tsens_0c_irq_thread);
> + }
> +
> return ret;
> }
>
> @@ -178,11 +208,22 @@ static int tsens_probe(struct platform_device *pdev)
> return -EINVAL;
> }
>
> - priv = devm_kzalloc(dev,
> - struct_size(priv, sensor, num_sensors),
> - GFP_KERNEL);
> - if (!priv)
> - return -ENOMEM;
> + /* Check for 0c interrupt is enabled or not */
> + if (platform_get_irq_byname(pdev, "zeroc") > 0) {
> + priv = devm_kzalloc(dev,
> + struct_size(priv, sensor, num_sensors + 1),
> + GFP_KERNEL);

Instead of doing this, simply do the following,

if (platform_get_irq_byname(pdev, "zeroc") > 0) {
num_sensors++;

The kzalloc will just work then, no?

> + if (!priv)
> + return -ENOMEM;
> + /* Use Max sensor index as 0c sensor hw_id */
> + priv->sensor[num_sensors].hw_id = data->feat->max_sensors;
> + } else {
> + priv = devm_kzalloc(dev,
> + struct_size(priv, sensor, num_sensors),
> + GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> + }
>
> priv->dev = dev;
> priv->num_sensors = num_sensors;
> diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
> index 502acf0e6828..5b53a0352b4d 100644
> --- a/drivers/thermal/qcom/tsens.h
> +++ b/drivers/thermal/qcom/tsens.h
> @@ -34,6 +34,7 @@ enum tsens_irq_type {
> LOWER,
> UPPER,
> CRITICAL,
> + ZEROC,
> };
>
> /**
> @@ -64,6 +65,7 @@ struct tsens_sensor {
> * @suspend: Function to suspend the tsens device
> * @resume: Function to resume the tsens device
> * @get_trend: Function to get the thermal/temp trend
> + * @get_0c_status: Function to get the 0c interrupt status
> */
> struct tsens_ops {
> /* mandatory callbacks */
> @@ -76,6 +78,7 @@ struct tsens_ops {
> int (*suspend)(struct tsens_priv *priv);
> int (*resume)(struct tsens_priv *priv);
> int (*get_trend)(struct tsens_sensor *s, enum thermal_trend *trend);
> + int (*get_0c_status)(const struct tsens_sensor *s, int *temp);
> };
>
> #define REG_FIELD_FOR_EACH_SENSOR11(_name, _offset, _startbit, _stopbit) \
> @@ -161,6 +164,8 @@ enum regfield_ids {
> TSENS_SW_RST,
> SENSOR_EN,
> CODE_OR_TEMP,
> + /* 0C CTRL OFFSET */
> + TSENS_0C_INT_EN,
>
> /* ----- TM ------ */
> /* TRDY */
> @@ -485,6 +490,8 @@ enum regfield_ids {
> MAX_STATUS_14,
> MAX_STATUS_15,
>
> + TSENS_0C_STATUS, /* 0C INTERRUPT status */
> +
> /* Keep last */
> MAX_REGFIELDS
> };
> @@ -497,6 +504,7 @@ enum regfield_ids {
> * @srot_split: does the IP neatly splits the register space into SROT and TM,
> * with SROT only being available to secure boot firmware?
> * @has_watchdog: does this IP support watchdog functionality?
> + * @zero_c_int: does this IP support 0C interrupt ?
> * @max_sensors: maximum sensors supported by this version of the IP
> */
> struct tsens_features {
> @@ -505,6 +513,7 @@ struct tsens_features {
> unsigned int adc:1;
> unsigned int srot_split:1;
> unsigned int has_watchdog:1;
> + unsigned int zero_c_int:1;

zeroc_interrupt

> unsigned int max_sensors;
> };
>
> @@ -580,11 +589,13 @@ void compute_intercept_slope(struct tsens_priv *priv, u32 *pt1, u32 *pt2, u32 mo
> int init_common(struct tsens_priv *priv);
> int get_temp_tsens_valid(const struct tsens_sensor *s, int *temp);
> int get_temp_common(const struct tsens_sensor *s, int *temp);
> +int tsens_get_0c_int_status(const struct tsens_sensor *s, int *temp);
> int tsens_enable_irq(struct tsens_priv *priv);
> void tsens_disable_irq(struct tsens_priv *priv);
> int tsens_set_trips(void *_sensor, int low, int high);
> irqreturn_t tsens_irq_thread(int irq, void *data);
> irqreturn_t tsens_critical_irq_thread(int irq, void *data);
> +irqreturn_t tsens_0c_irq_thread(int irq, void *data);
>
> /* TSENS target */
> extern struct tsens_plat_data data_8960;
> --
> 2.26.2

\
 
 \ /
  Last update: 2020-05-05 14:10    [W:0.296 / U:0.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site