lkml.org 
[lkml]   [2020]   [May]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 06/11] net: ethernet: mtk-eth-mac: new driver
> +static struct net_device *mtk_mac_get_netdev(struct mtk_mac_priv *priv)
> +{
> + char *ptr = (char *)priv;
> +
> + return (struct net_device *)(ptr - ALIGN(sizeof(struct net_device),
> + NETDEV_ALIGN));
> +}

Bit of an odd way to do it. It is much more normal to just have

return priv->netdev;

> +static struct sk_buff *mtk_mac_alloc_skb(struct net_device *ndev)
> +{
> + uintptr_t tail, offset;
> + struct sk_buff *skb;
> +
> + skb = dev_alloc_skb(MTK_MAC_MAX_FRAME_SIZE);
> + if (!skb)
> + return NULL;
> +
> + /* Align to 16 bytes. */
> + tail = (uintptr_t)skb_tail_pointer(skb);
> + if (tail & (MTK_MAC_SKB_ALIGNMENT - 1)) {
> + offset = tail & (MTK_MAC_SKB_ALIGNMENT - 1);
> + skb_reserve(skb, MTK_MAC_SKB_ALIGNMENT - offset);
> + }
> +
> + /* Ensure 16-byte alignment of the skb pointer: eth_type_trans() will
> + * extract the Ethernet header (14 bytes) so we need two more bytes.
> + */
> + skb_reserve(skb, 2);

NET_IP_ALIGN

There might also be something in skbuf.h which will do your 16 byte
alignment for you.

> +static int mtk_mac_enable(struct net_device *ndev)
> +{
> + struct mtk_mac_priv *priv = netdev_priv(ndev);
> + unsigned int val;
> + int ret;
> +
> + mtk_mac_nic_disable_pd(priv);
> + mtk_mac_intr_mask_all(priv);
> + mtk_mac_dma_stop(priv);
> + netif_carrier_off(ndev);

Attaching the PHY will turn the carrier off. If you are using phylib
correctly, you should not have to touch the carrier status, phylib
will do it for you.

> + /* Configure flow control */
> + val = MTK_MAC_VAL_FC_CFG_SEND_PAUSE_TH_2K;
> + val <<= MTK_MAC_OFF_FC_CFG_SEND_PAUSE_TH;
> + val |= MTK_MAC_BIT_FC_CFG_BP_EN;
> + val |= MTK_MAC_BIT_FC_CFG_UC_PAUSE_DIR;
> + regmap_write(priv->regs, MTK_MAC_REG_FC_CFG, val);
> +
> + /* Set SEND_PAUSE_RLS to 1K */
> + val = MTK_MAC_VAL_EXT_CFG_SND_PAUSE_RLS_1K;
> + val <<= MTK_MAC_OFF_EXT_CFG_SND_PAUSE_RLS;
> + regmap_write(priv->regs, MTK_MAC_REG_EXT_CFG, val);

Pause is something this is auto-negotiated. You should be setting this
in your link change notifier which phylib will call when the link goes
up.

> +static int mtk_mac_mdio_rwok_wait(struct mtk_mac_priv *priv)
> +{
> + unsigned long start = jiffies;
> + unsigned int val;
> +
> + for (;;) {
> + regmap_read(priv->regs, MTK_MAC_REG_PHY_CTRL0, &val);
> + if (val & MTK_MAC_BIT_PHY_CTRL0_RWOK)
> + break;
> +
> + udelay(10);
> + if (time_after(jiffies, start + MTK_MAC_WAIT_TIMEOUT))
> + return -ETIMEDOUT;
> + }

regmap_read_poll_timeout() ?

> +static int mtk_mac_mdio_read(struct mii_bus *mii, int phy_id, int regnum)
> +{
> + struct mtk_mac_priv *priv = mii->priv;
> + unsigned int val, data;
> + int ret;

It would be good if here and in _write() you check for C45 addresses
and return -EOPNOTSUP.

> +
> + mtk_mac_mdio_rwok_clear(priv);
> +
> + val = (regnum << MTK_MAC_OFF_PHY_CTRL0_PREG);
> + val &= MTK_MAC_MSK_PHY_CTRL0_PREG;
> + val |= MTK_MAC_BIT_PHY_CTRL0_RDCMD;
> +
> + regmap_write(priv->regs, MTK_MAC_REG_PHY_CTRL0, val);
> +
> + ret = mtk_mac_mdio_rwok_wait(priv);
> + if (ret)
> + return ret;
> +
> + regmap_read(priv->regs, MTK_MAC_REG_PHY_CTRL0, &data);
> +
> + data &= MTK_MAC_MSK_PHY_CTRL0_RWDATA;
> + data >>= MTK_MAC_OFF_PHY_CTRL0_RWDATA;
> +
> + return data;
> +}

> +static int mtk_mac_mdio_init(struct net_device *ndev)
> +{
> + struct mtk_mac_priv *priv = netdev_priv(ndev);
> + struct device *dev = mtk_mac_get_dev(priv);
> + struct device_node *of_node, *mdio_node;
> + int ret;
> +
> + of_node = dev->of_node;
> +
> + mdio_node = of_get_child_by_name(of_node, "mdio");
> + if (!mdio_node)
> + return -ENODEV;
> +
> + if (!of_device_is_available(mdio_node)) {
> + ret = -ENODEV;
> + goto out_put_node;
> + }
> +
> + priv->mii = devm_mdiobus_alloc(dev);
> + if (!priv->mii) {
> + ret = -ENOMEM;
> + goto out_put_node;
> + }
> +
> + snprintf(priv->mii->id, MII_BUS_ID_SIZE, "%s", dev_name(dev));
> + priv->mii->name = "mdio";

It is normal to include something like 'MTK' in the name.

> + priv->mii->parent = dev;
> + priv->mii->read = mtk_mac_mdio_read;
> + priv->mii->write = mtk_mac_mdio_write;
> + priv->mii->priv = priv;
> +
> + ret = of_mdiobus_register(priv->mii, mdio_node);
> +
> +out_put_node:
> + of_node_put(mdio_node);
> + return ret;
> +}

Andrew

\
 
 \ /
  Last update: 2020-05-05 19:48    [W:0.196 / U:0.156 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site