lkml.org 
[lkml]   [2020]   [May]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 05/11] power: bq25890: fix ADC mode configuration
Hi,

On Sun, May 03, 2020 at 05:21:11PM +0200, Michał Mirosław wrote:
> Datasheet describes two modes for reading ADC measurements:
> 1. continuous, 1 Hz - enabled and started by CONV_RATE bit
> 2. one-shot - triggered by CONV_START bit
>
> In continuous mode, CONV_START is read-only and signifies an ongoing
> conversion.
>
> Change the code to follow the datasheet and really disable continuous
> mode for power saving.
>
> Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
> ---
> drivers/power/supply/bq25890_charger.c | 33 ++++++++++++++++++++++----
> 1 file changed, 28 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/power/supply/bq25890_charger.c b/drivers/power/supply/bq25890_charger.c
> index 9339e216651f..3b02fa80aedd 100644
> --- a/drivers/power/supply/bq25890_charger.c
> +++ b/drivers/power/supply/bq25890_charger.c
> @@ -126,6 +126,7 @@ static const struct regmap_access_table bq25890_writeable_regs = {
>
> static const struct regmap_range bq25890_volatile_reg_ranges[] = {
> regmap_reg_range(0x00, 0x00),
> + regmap_reg_range(0x02, 0x02),
> regmap_reg_range(0x09, 0x09),
> regmap_reg_range(0x0b, 0x14),
> };
> @@ -374,18 +375,40 @@ enum bq25890_chrg_fault {
> CHRG_FAULT_TIMER_EXPIRED,
> };
>
> +static bool bq25890_is_adc_property(enum power_supply_property psp)
> +{
> + switch (psp) {
> + case POWER_SUPPLY_PROP_INPUT_VOLTAGE_NOW:
> + case POWER_SUPPLY_PROP_OUTPUT_VOLTAGE_NOW:

^^^ does not compile without your other patchset, so not applied.

When you send a new version, please Cc some of the recent
contributors to bq25890_charger.c, so that they have a chance
to test the changes with their setup:

Angus Ainslie (Purism) <angus@akkea.ca>
Yauhen Kharuzhy <jekhor@gmail.com>

-- Sebastian

> + case POWER_SUPPLY_PROP_VOLTAGE_NOW:
> + case POWER_SUPPLY_PROP_CURRENT_NOW:
> + return true;
> +
> + default:
> + return false;
> + }
> +}
> +
> static int bq25890_power_supply_get_property(struct power_supply *psy,
> enum power_supply_property psp,
> union power_supply_propval *val)
> {
> - int ret;
> struct bq25890_device *bq = power_supply_get_drvdata(psy);
> struct bq25890_state state;
> + bool do_adc_conv;
> + int ret;
>
> mutex_lock(&bq->lock);
> state = bq->state;
> + do_adc_conv = !state.online && bq25890_is_adc_property(psp);
> + if (do_adc_conv)
> + bq25890_field_write(bq, F_CONV_START, 1);
> mutex_unlock(&bq->lock);
>
> + if (do_adc_conv)
> + regmap_field_read_poll_timeout(bq->rmap_fields[F_CONV_START],
> + ret, !ret, 25000, 1000000);
> +
> switch (psp) {
> case POWER_SUPPLY_PROP_STATUS:
> if (!state.online)
> @@ -623,8 +646,8 @@ static int bq25890_hw_init(struct bq25890_device *bq)
> }
> }
>
> - /* Configure ADC for continuous conversions. This does not enable it. */
> - ret = bq25890_field_write(bq, F_CONV_RATE, 1);
> + /* Configure ADC for continuous conversions when charging */
> + ret = bq25890_field_write(bq, F_CONV_RATE, !!bq->state.online);
> if (ret < 0) {
> dev_dbg(bq->dev, "Config ADC failed %d\n", ret);
> return ret;
> @@ -966,7 +989,7 @@ static int bq25890_suspend(struct device *dev)
> * If charger is removed, while in suspend, make sure ADC is diabled
> * since it consumes slightly more power.
> */
> - return bq25890_field_write(bq, F_CONV_START, 0);
> + return bq25890_field_write(bq, F_CONV_RATE, 0);
> }
>
> static int bq25890_resume(struct device *dev)
> @@ -982,7 +1005,7 @@ static int bq25890_resume(struct device *dev)
>
> /* Re-enable ADC only if charger is plugged in. */
> if (bq->state.online) {
> - ret = bq25890_field_write(bq, F_CONV_START, 1);
> + ret = bq25890_field_write(bq, F_CONV_RATE, 1);
> if (ret < 0)
> return ret;
> }
> --
> 2.20.1
>
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2020-05-03 22:03    [W:0.090 / U:0.180 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site