lkml.org 
[lkml]   [2020]   [May]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v8 02/19] spi: spi-mem: allow specifying a command's extension
On Sat, 23 May 2020 04:10:25 +0530
Pratyush Yadav <p.yadav@ti.com> wrote:

> diff --git a/drivers/spi/spi-mxic.c b/drivers/spi/spi-mxic.c
> index 69491f3a515d..4e4292f0ee1d 100644
> --- a/drivers/spi/spi-mxic.c
> +++ b/drivers/spi/spi-mxic.c
> @@ -356,6 +356,7 @@ static int mxic_spi_mem_exec_op(struct spi_mem *mem,
> int nio = 1, i, ret;
> u32 ss_ctrl;
> u8 addr[8];
> + u8 opcode = op->cmd.opcode & 0xff;

You don't need the '& 0xff' here, the cast to an u8 will truncate the
value anyway.

>
> ret = mxic_spi_set_freq(mxic, mem->spi->max_speed_hz);
> if (ret)
> @@ -393,7 +394,7 @@ static int mxic_spi_mem_exec_op(struct spi_mem *mem,
> writel(readl(mxic->regs + HC_CFG) | HC_CFG_MAN_CS_ASSERT,
> mxic->regs + HC_CFG);
>
> - ret = mxic_spi_data_xfer(mxic, &op->cmd.opcode, NULL, 1);
> + ret = mxic_spi_data_xfer(mxic, &opcode, NULL, 1);
> if (ret)
> goto out;
>
> diff --git a/drivers/spi/spi-zynq-qspi.c b/drivers/spi/spi-zynq-qspi.c
> index 17641157354d..41389856e14a 100644
> --- a/drivers/spi/spi-zynq-qspi.c
> +++ b/drivers/spi/spi-zynq-qspi.c
> @@ -527,20 +527,21 @@ static int zynq_qspi_exec_mem_op(struct spi_mem *mem,
> struct zynq_qspi *xqspi = spi_controller_get_devdata(mem->spi->master);
> int err = 0, i;
> u8 *tmpbuf;
> + u8 opcode = op->cmd.opcode & 0xff;
>

Ditto.

> dev_dbg(xqspi->dev, "cmd:%#x mode:%d.%d.%d.%d\n",
> - op->cmd.opcode, op->cmd.buswidth, op->addr.buswidth,
> + opcode, op->cmd.buswidth, op->addr.buswidth,
> op->dummy.buswidth, op->data.buswidth);
>
> zynq_qspi_chipselect(mem->spi, true);
> zynq_qspi_config_op(xqspi, mem->spi);
>
> - if (op->cmd.opcode) {
> + if (opcode) {

Unrelated to this patch, but this test is wrong. I don't see why we
couldn't have a '0' opcode. The test should be dropped or done on the
new op->cmd.nbytes field.

> reinit_completion(&xqspi->data_completion);
> - xqspi->txbuf = (u8 *)&op->cmd.opcode;
> + xqspi->txbuf = &opcode;
> xqspi->rxbuf = NULL;
> - xqspi->tx_bytes = sizeof(op->cmd.opcode);
> - xqspi->rx_bytes = sizeof(op->cmd.opcode);
> + xqspi->tx_bytes = op->cmd.nbytes;
> + xqspi->rx_bytes = op->cmd.nbytes;
> zynq_qspi_write_op(xqspi, ZYNQ_QSPI_FIFO_DEPTH, true);
> zynq_qspi_write(xqspi, ZYNQ_QSPI_IEN_OFFSET,
> ZYNQ_QSPI_IXR_RXTX_MASK);

\
 
 \ /
  Last update: 2020-05-24 22:18    [W:0.117 / U:7.948 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site