lkml.org 
[lkml]   [2020]   [May]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
Subjectx86: Question about state of general purpose registers on switch to 64-bit mode
Hi,

I have a question about the state of the upper 32 bits of the general
purpose registers following a switch from/to 64-bit mode.

Both the AMD [0] and Intel [1] manuals state that these bits are
undefined following a switch from 64 to 32-bit mode. Since they can't be
accessed in 32-bit mode, presumably this means they are undefined once
you switch back to 64-bit mode and can see them again.

However, at least the compressed kernel boot code in head_64.S makes
assumptions about these bits:

(1) We assume that registers that are set in 32-bit mode will have their
upper 32 bits clear when we switch to 64-bit mode. Eg the bootparams
pointer in %esi in startup_32 is assumed to remain valid following the
switch to the 64-bit startup_64 (or the EFI stub). The EFI stub assumes
that the 32-bit %esp setup in startup_32 will remain valid.

(2) We assume that 64-bit registers that are not touched by the 32-bit
code will retain their full 64-bit values on switching back. The 5-level
trampoline logic makes this assumption and depends on %rbx, %rbp, %rsi, %rdi
retaining their values.

Given that we don't keep seeing random boot failures, I would guess that
the above assumptions are actually valid in practice. However, they do
seem to be more than what the processors actually promise. I have a
preliminary patch to remove assumption (2) for the trampoline code at
the end of this e-mail, and I'm wondering if there is interest in doing
that + fixing up the rest of the boot code.

Thanks.

[0] https://www.amd.com/system/files/TechDocs/40332.pdf
Section 3.1.2.4 (GPR High 32 Bits Across Mode Switches):

The processor does not preserve the upper 32 bits of the 64-bit GPRs
across switches from 64-bit mode to compatibility or legacy modes. When
using 32-bit operands in compatibility or legacy mode, the high 32 bits
of GPRs are undefined. Software must not rely on these undefined bits,
because they can change from one implementation to the next or even on a
cycle-to-cycle basis within a given implementation. The undefined bits
are not a function of the data left by any previously running process.

[1] https://software.intel.com/content/dam/develop/public/us/en/documents/325462-sdm-vol-1-2abcd-3abcd.pdf
Volume 1, Section 3.4.1.1 (General-Purpose Registers in 64-Bit Mode):

Registers only available in 64-bit mode (R8-R15 and XMM8-XMM15) are
preserved across transitions from 64-bit mode into compatibility mode
then back into 64-bit mode. However, values of R8-R15 and XMM8-XMM15 are
undefined after transitions from 64-bit mode through compatibility mode
to legacy or real mode and then back through compatibility mode to
64-bit mode.
...
Because the upper 32 bits of 64-bit general-purpose registers are
undefined in 32-bit modes, the upper 32 bits of any general-purpose
register are not preserved when switching from 64-bit mode to a 32-bit
mode (to protected mode or compatibility mode). Software must not depend
on these bits to maintain a value after a 64-bit to 32-bit mode switch.

diff --git a/arch/x86/boot/compressed/head_64.S b/arch/x86/boot/compressed/head_64.S
index 4f7e6b84be07..4e3d41d0c3ca 100644
--- a/arch/x86/boot/compressed/head_64.S
+++ b/arch/x86/boot/compressed/head_64.S
@@ -404,43 +404,61 @@ SYM_CODE_START(startup_64)
* paging.
*
* RSI holds real mode data and needs to be preserved across
- * this function call.
+ * the trampoline setup/call/cleanup.
*/
pushq %rsi
+
movq %rsi, %rdi /* real mode address */
call paging_prepare
- popq %rsi

/* Save the trampoline address in RCX */
movq %rax, %rcx

+ /* Save registers across trampoline call */
+ pushq %rbx
+ pushq %rbp
+ movq %rsp, %rbp
+
+ /* Set up data and stack segments */
+ movl $__KERNEL_DS, %eax
+ movl %eax, %ds
+ movl %eax, %ss
+
+ /* Set up new stack for the trampoline */
+ leaq TRAMPOLINE_32BIT_STACK_END(%rcx), %rsp
+ /* Save the old stack pointer */
+ pushq %rbp
+
/*
- * Load the address of trampoline_return() into RDI.
+ * Push the address of trampoline_return().
* It will be used by the trampoline to return to the main code.
*/
- leaq trampoline_return(%rip), %rdi
+ leaq trampoline_return(%rip), %rax
+ pushq %rax

/* Switch to compatibility mode (CS.L = 0 CS.D = 1) via far return */
pushq $__KERNEL32_CS
- leaq TRAMPOLINE_32BIT_CODE_OFFSET(%rax), %rax
+ leaq TRAMPOLINE_32BIT_CODE_OFFSET(%rcx), %rax
pushq %rax
lretq
trampoline_return:
/* Restore the stack, the 32-bit trampoline uses its own stack */
- leaq boot_stack_end(%rbx), %rsp
+ popq %rsp
+
+ /* Restore saved registers */
+ popq %rbp
+ popq %rbx

/*
* cleanup_trampoline() would restore trampoline memory.
*
* RDI is address of the page table to use instead of page table
* in trampoline memory (if required).
- *
- * RSI holds real mode data and needs to be preserved across
- * this function call.
*/
- pushq %rsi
leaq top_pgtable(%rbx), %rdi
call cleanup_trampoline
+
+ /* Restore RSI */
popq %rsi

/* Zero EFLAGS */
@@ -569,14 +587,6 @@ SYM_FUNC_END(.Lrelocated)
* Non zero RDX means trampoline needs to enable 5-level paging.
*/
SYM_CODE_START(trampoline_32bit_src)
- /* Set up data and stack segments */
- movl $__KERNEL_DS, %eax
- movl %eax, %ds
- movl %eax, %ss
-
- /* Set up new stack */
- leal TRAMPOLINE_32BIT_STACK_END(%ecx), %esp
-
/* Disable paging */
movl %cr0, %eax
btrl $X86_CR0_PG_BIT, %eax
@@ -635,8 +645,10 @@ SYM_CODE_END(trampoline_32bit_src)

.code64
SYM_FUNC_START_LOCAL_NOALIGN(.Lpaging_enabled)
+ /* Make sure upper 32 bits of %rsp are clear */
+ movl %esp, %esp
/* Return from the trampoline */
- jmp *%rdi
+ retq
SYM_FUNC_END(.Lpaging_enabled)

/*
\
 
 \ /
  Last update: 2020-05-23 17:58    [W:0.034 / U:0.600 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site