[lkml]   [2020]   [May]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
SubjectRe: [PATCH 3/4] remoteproc: add support for a new 64-bit trace version
Hi Clement,

> > ----- On 22 May, 2020, at 20:03, Clément Leger wrote:>
>> Hi Suman,
>> ----- On 22 May, 2020, at 19:33, Bjorn Andersson
>> wrote:
>>> On Fri 22 May 09:54 PDT 2020, Suman Anna wrote:
>>>> On 5/21/20 2:42 PM, Suman Anna wrote:
>>>>> Hi Bjorn,
>>>>> On 5/21/20 1:04 PM, Bjorn Andersson wrote:
>>>>>> On Wed 25 Mar 13:47 PDT 2020, Suman Anna wrote:
>>> [..]
>>>>>>> diff --git a/include/linux/remoteproc.h b/include/linux/remoteproc.h
>>> [..]
>>>>>>> +struct fw_rsc_trace2 {
>>>>>> Sounds more like fw_rsc_trace64 to me - in particular since the version
>>>>>> of trace2 is 1...
>>>>> Yeah, will rename this.
>>>>>>> +    u32 padding;
>>>>>>> +    u64 da;
>>>>>>> +    u32 len;
>>>>>>> +    u32 reserved;
>>>>>> What's the purpose of this reserved field?
>>>>> Partly to make sure the entire resource is aligned on an 8-byte, and
>>>>> partly copied over from fw_rsc_trace entry. I guess 32-bits is already
>>>>> large enough of a size for trace entries irrespective of 32-bit or
>>>>> 64-bit traces, so I doubt if we want to make the len field also a u64.
>>>> Looking at this again, I can drop both padding and reserved fields, if I
>>>> move the len field before da. Any preferences/comments?
> Sorry, my message went a bit too fast... So as I was saying:
> Not only the in-structure alignment matters but also in the resource table.
> Since the resource table is often packed (see [1] for instance), if a trace
> resource is embedded in the resource table after another resource aligned
> on 32 bits only, your 64 bits trace field will potentially end up
> misaligned.

Right. Since one can mix and match the resources of different sizes and
include them in any order, the onus is going to be on the resource table
constructors to ensure the inter-resource alignments, if any are
required. The resource table format allows you to add padding fields in
between if needed, and the remoteproc core relies on the offsets.

I can only ensure the alignment within this resource structure with
ready-available access and conversion to/from a 64-bit type, as long as
the resource is starting on a 64-bit boundary.

> To overcome this, there is multiple solutions:
> - Split the 64 bits fields into 32bits low and high parts:
> Since all resources are aligned on 32bits, it will be ok

Yes, this is one solution. At the same time, this means you need
additional conversion logic for converting to and from 64-bit field. In
this particular case, da is the address of the trace buffer pointer on a
64-bit processor, so we can directly use the address of the trace
buffer. Guess it is a question of easier translation vs packing the
resource table as tight as possible.

> - Use memcpy_from/to_io when reading/writing such fields
> As I said in a previous message this should probably be used since
> the memories that are accessed by rproc are io mem (ioremap in almost
> all drivers).

Anything running out of DDR actually doesn't need the io mem semantics,
so we actually need to be fixing the drivers. Blindly changing the
current memcpy to memcpy_to_io in the core loader is also not right. Any
internal memories properties will actually depend on the processor and
SoC. Eg: The R5 TCM interfaces in general can be treated as normal memories.


> Regards,
> Clément
> [1]
>>> Sounds good to me.
>>> Thanks,
>>> Bjorn

 \ /
  Last update: 2020-05-22 20:59    [W:0.133 / U:0.160 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site